[PATCH 6/6] ARM: nomadik: device tree for NHK15 board
Linus Walleij
linus.walleij at linaro.org
Fri Oct 31 13:45:35 PDT 2014
This adds a device tree for the Nomadik NHK15 development kit
board.
Signed-off-by: Linus Walleij <linus.walleij at linaro.org>
---
.../devicetree/bindings/arm/ste-nomadik.txt | 6 +
arch/arm/boot/dts/Makefile | 3 +-
arch/arm/boot/dts/ste-nomadik-nhk15.dts | 151 +++++++++++++++++++++
arch/arm/mach-nomadik/cpu-8815.c | 1 +
4 files changed, 160 insertions(+), 1 deletion(-)
create mode 100644 arch/arm/boot/dts/ste-nomadik-nhk15.dts
diff --git a/Documentation/devicetree/bindings/arm/ste-nomadik.txt b/Documentation/devicetree/bindings/arm/ste-nomadik.txt
index 6256ec31666d..2fdff5a806cf 100644
--- a/Documentation/devicetree/bindings/arm/ste-nomadik.txt
+++ b/Documentation/devicetree/bindings/arm/ste-nomadik.txt
@@ -10,6 +10,12 @@ Required root node property: src
Boards with the Nomadik SoC include:
+Nomadik NHK-15 board manufactured by ST Microelectronics:
+
+Required root node property:
+
+compatible="st,nomadik-nhk-15";
+
S8815 "MiniKit" manufactured by Calao Systems:
Required root node property:
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 38c89cafa1ab..50bb73ec2b7d 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -274,7 +274,8 @@ dtb-$(CONFIG_ARCH_MXS) += imx23-evk.dtb \
imx28-m28evk.dtb \
imx28-sps1.dtb \
imx28-tx28.dtb
-dtb-$(CONFIG_ARCH_NOMADIK) += ste-nomadik-s8815.dtb
+dtb-$(CONFIG_ARCH_NOMADIK) += ste-nomadik-s8815.dtb \
+ ste-nomadik-nhk15.dtb
dtb-$(CONFIG_ARCH_NSPIRE) += nspire-cx.dtb \
nspire-tp.dtb \
nspire-clp.dtb
diff --git a/arch/arm/boot/dts/ste-nomadik-nhk15.dts b/arch/arm/boot/dts/ste-nomadik-nhk15.dts
new file mode 100644
index 000000000000..a8c00ee7522a
--- /dev/null
+++ b/arch/arm/boot/dts/ste-nomadik-nhk15.dts
@@ -0,0 +1,151 @@
+/*
+ * Device Tree for the ST-Ericsson Nomadik S8815 board
+ * Produced by Calao Systems
+ */
+
+/dts-v1/;
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/gpio/gpio.h>
+#include "ste-nomadik-stn8815.dtsi"
+
+/ {
+ model = "Nomadik STN8815NHK";
+ compatible = "st,nomadik-nhk-15";
+
+ chosen {
+ bootargs = "root=/dev/ram0 console=ttyAMA1,115200n8 earlyprintk";
+ };
+
+ aliases {
+ stmpe-i2c0 = &stmpe0;
+ stmpe-i2c1 = &stmpe1;
+ };
+
+ pinctrl {
+ stmpe2401_1 {
+ stmpe2401_1_nhk_mode: stmpe2401_1_nhk {
+ nhk_cfg1 {
+ ste,pins = "GPIO76_B20"; // IRQ line
+ ste,input = <0>;
+ };
+ nhk_cfg2 {
+ ste,pins = "GPIO77_B8"; // reset line
+ ste,output = <1>;
+ };
+ };
+ };
+ stmpe2401_2 {
+ stmpe2401_2_nhk_mode: stmpe2401_2_nhk {
+ nhk_cfg1 {
+ ste,pins = "GPIO78_A8"; // IRQ line
+ ste,input = <0>;
+ };
+ nhk_cfg2 {
+ ste,pins = "GPIO79_C9"; // reset line
+ ste,output = <1>;
+ };
+ };
+ };
+ };
+
+ src at 101e0000 {
+ /* These chrystal outputs are not used on this board */
+ disable-sxtalo;
+ disable-mxtalo;
+ };
+
+ /* This is where the interrupt is routed on the NHK-15 debug board */
+ external-bus at 34000000 {
+ compatible = "simple-bus";
+ reg = <0x34000000 0x1000000>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 0x34000000 0x1000000>;
+ ethernet at 300 {
+ compatible = "smsc,lan91c111";
+ reg = <0x300 0x0fd00>;
+ reg-io-width = <2>;
+ reset-gpios = <&stmpe_gpio44 10 GPIO_ACTIVE_HIGH>;
+ interrupt-parent = <&stmpe_gpio44>;
+ interrupts = <11 IRQ_TYPE_EDGE_RISING>;
+ };
+ };
+
+ i2c0 {
+ stmpe0: stmpe2401 at 43 {
+ compatible = "st,stmpe2401";
+ reg = <0x43>;
+ reset-gpios = <&gpio2 13 GPIO_ACTIVE_LOW>; // GPIO77
+ interrupts = <12 IRQ_TYPE_EDGE_FALLING>; // GPIO76
+ interrupt-parent = <&gpio2>;
+ interrupt-controller;
+ wakeup-source;
+ pinctrl-names = "default";
+ pinctrl-0 = <&stmpe2401_1_nhk_mode>;
+ stmpe_gpio43: stmpe_gpio {
+ compatible = "st,stmpe-gpio";
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ /* Some pins in alternate functions */
+ st,norequest-mask = <0xf0f002>;
+ };
+ stmpe_keypad {
+ compatible = "st,stmpe-keypad";
+ debounce-interval = <64>;
+ st,scan-count = <8>;
+ st,no-autorepeat;
+ keypad,num-rows = <8>;
+ keypad,num-columns = <8>;
+ linux,keymap = <0x00020072 // Vol down
+ 0x00030073 // Vol up
+ 0x0100009e // Back
+ 0x010100e3 // TV out
+ 0x01020098 // Lock
+ 0x0103013b // Start
+ 0x020000a3 // Next
+ 0x020100a4 // Play
+ 0x020200a5 // Prev
+ 0x02030160 // OK
+ 0x03000069 // Left
+ 0x0301006a // Right
+ 0x03020067 // Up
+ 0x0303006c>; // Down
+ };
+ };
+ stmpe1: stmpe2401 at 44 {
+ compatible = "st,stmpe2401";
+ reg = <0x44>;
+ reset-gpios = <&gpio2 15 GPIO_ACTIVE_LOW>; // GPIO79
+ interrupts = <14 IRQ_TYPE_EDGE_FALLING>; // GPIO78
+ interrupt-parent = <&gpio2>;
+ interrupt-controller;
+ wakeup-source;
+ pinctrl-names = "default";
+ pinctrl-0 = <&stmpe2401_2_nhk_mode>;
+ stmpe_gpio44: stmpe_gpio {
+ compatible = "st,stmpe-gpio";
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+ };
+ };
+
+ amba {
+ mmcsd: sdi at 101f6000 {
+ cd-gpios = <&stmpe_gpio44 7 GPIO_ACTIVE_LOW>;
+ wp-gpios = <&stmpe_gpio44 18 GPIO_ACTIVE_HIGH>;
+ };
+ };
+
+ /* Custom board node with GPIO pins to active etc */
+ usb-s8815 {
+ /* This will turn off SATA so that MMC/SD can thrive */
+ mmcsd-gpio {
+ gpios = <&stmpe_gpio44 2 0x1>;
+ };
+ };
+};
diff --git a/arch/arm/mach-nomadik/cpu-8815.c b/arch/arm/mach-nomadik/cpu-8815.c
index 9116ca476d7c..9bda46f1fab7 100644
--- a/arch/arm/mach-nomadik/cpu-8815.c
+++ b/arch/arm/mach-nomadik/cpu-8815.c
@@ -144,6 +144,7 @@ static int __init cpu8815_mmcsd_init(void)
device_initcall(cpu8815_mmcsd_init);
static const char * cpu8815_board_compat[] = {
+ "st,nomadik-nhk-15",
"calaosystems,usb-s8815",
NULL,
};
--
1.9.3
More information about the linux-arm-kernel
mailing list