[PATCH v3 12/14] ARM: dts: exynos4412-trats: Switch max77686 regulators to GPIO control

[Krzysztof Kozlowski]

Remove fixed regulators (duplicating what max77686 provides) and
add GPIO control to max77686 regulators. Add of_compatible to
voltage-regulators node.

This gives the system full control over those regulators. Previously
the state of such regulators was a mixture of what max77686 driver set
over I2C and what regulator-fixed set through GPIO.

Removal of 'regulator-always-on' from CAM_ISP_CORE_1.2V (buck9) allows
disabling it when it is not used. Previously this regulator was always
enabled because its enable state is a OR of:
 - ENB9 GPIO (turned by regulator-fixed),
 - BUCK9EN field in BUCK9CTRL register (max77686 through I2C).

Signed-off-by: Krzysztof Kozlowski <k.kozlowski at samsung.com>
---
 arch/arm/boot/dts/exynos4412-trats2.dts | 28 ++++++++--------------------
 1 file changed, 8 insertions(+), 20 deletions(-)

diff --git a/arch/arm/boot/dts/exynos4412-trats2.dts b/arch/arm/boot/dts/exynos4412-trats2.dts
index 7a68e0832cd6..ebbd12d1fe9a 100644
--- a/arch/arm/boot/dts/exynos4412-trats2.dts
+++ b/arch/arm/boot/dts/exynos4412-trats2.dts
@@ -58,15 +58,6 @@
 		#address-cells = <1>;
 		#size-cells = <0>;
 
-		vemmc_reg: regulator-0 {
-			compatible = "regulator-fixed";
-			regulator-name = "VMEM_VDD_2.8V";
-			regulator-min-microvolt = <2800000>;
-			regulator-max-microvolt = <2800000>;
-			gpio = <&gpk0 2 0>;
-			enable-active-high;
-		};
-
 		cam_io_reg: voltage-regulator-1 {
 			compatible = "regulator-fixed";
 			regulator-name = "CAM_SENSOR_A";
@@ -94,16 +85,6 @@
 			enable-active-high;
 		};
 
-		cam_isp_core_reg: voltage-regulator-4 {
-			compatible = "regulator-fixed";
-			regulator-name = "CAM_ISP_CORE_1.2V_EN";
-			regulator-min-microvolt = <1200000>;
-			regulator-max-microvolt = <1200000>;
-			gpio = <&gpm0 3 0>;
-			enable-active-high;
-			regulator-always-on;
-		};
-
 		ps_als_reg: voltage-regulator-5 {
 			compatible = "regulator-fixed";
 			regulator-name = "LED_A_3.0V";
@@ -221,6 +202,13 @@
 			#clock-cells = <1>;
 
 			voltage-regulators {
+				compatible = "maxim,max77686-pmic";
+
+				ldo21-gpio = <&gpy2 0 GPIO_ACTIVE_HIGH>;
+				ldo22-gpio = <&gpk0 2 GPIO_ACTIVE_HIGH>;
+				buck8-gpio = <&gpk0 2 GPIO_ACTIVE_HIGH>;
+				buck9-gpio = <&gpm0 3 GPIO_ACTIVE_HIGH>;
+
 				ldo1_reg: ldo1 {
 					regulator-compatible = "LDO1";
 					regulator-name = "VALIVE_1.0V_AP";
@@ -591,7 +579,7 @@
 		broken-cd;
 		non-removable;
 		card-detect-delay = <200>;
-		vmmc-supply = <&vemmc_reg>;
+		vmmc-supply = <&ldo22_reg>;
 		clock-frequency = <400000000>;
 		samsung,dw-mshc-ciu-div = <0>;
 		samsung,dw-mshc-sdr-timing = <2 3>;
-- 
1.9.1