[PATCH 01/10] ARM: dts: Fix bootloader version dependencies by muxing n900 smc91x pins

[Tony Lindgren]

Apparently some versions of nolo don't mux the necessary GPMC
pins for the smc91x probe to work properly. Let's fix this issue
by adding mux support for GPMC to the kernel.

Note that it's unclear why the GPMC clk pin has input enabled, but
let's not touch that as in general the mux settings in nolo are
correct.

Cc: Kevin Hilman <khilman at kernel.org>
Cc: Roger Quadros <rogerq at ti.com>
Signed-off-by: Tony Lindgren <tony at atomide.com>
---
 arch/arm/boot/dts/omap3-n900.dts | 29 +++++++++++++++++++++++++++++
 1 file changed, 29 insertions(+)

diff --git a/arch/arm/boot/dts/omap3-n900.dts b/arch/arm/boot/dts/omap3-n900.dts
index 739fcf2..e7210d1 100644
--- a/arch/arm/boot/dts/omap3-n900.dts
+++ b/arch/arm/boot/dts/omap3-n900.dts
@@ -142,6 +142,33 @@
 		>;
 	};
 
+	gpmc_pins: pinmux_gpmc_pins {
+		pinctrl-single,pins = <
+
+			/* address lines */
+                        OMAP3_CORE1_IOPAD(0x207a, PIN_OUTPUT | MUX_MODE0)       /* gpmc_a1.gpmc_a1 */
+                        OMAP3_CORE1_IOPAD(0x207c, PIN_OUTPUT | MUX_MODE0)       /* gpmc_a2.gpmc_a2 */
+                        OMAP3_CORE1_IOPAD(0x207e, PIN_OUTPUT | MUX_MODE0)       /* gpmc_a3.gpmc_a3 */
+
+			/* data lines, gpmc_d0..d7 not muxable according to TRM */
+                        OMAP3_CORE1_IOPAD(0x209e, PIN_INPUT | MUX_MODE0)        /* gpmc_d8.gpmc_d8 */
+                        OMAP3_CORE1_IOPAD(0x20a0, PIN_INPUT | MUX_MODE0)        /* gpmc_d9.gpmc_d9 */
+                        OMAP3_CORE1_IOPAD(0x20a2, PIN_INPUT | MUX_MODE0)        /* gpmc_d10.gpmc_d10 */
+                        OMAP3_CORE1_IOPAD(0x20a4, PIN_INPUT | MUX_MODE0)        /* gpmc_d11.gpmc_d11 */
+                        OMAP3_CORE1_IOPAD(0x20a6, PIN_INPUT | MUX_MODE0)        /* gpmc_d12.gpmc_d12 */
+                        OMAP3_CORE1_IOPAD(0x20a8, PIN_INPUT | MUX_MODE0)        /* gpmc_d13.gpmc_d13 */
+                        OMAP3_CORE1_IOPAD(0x20aa, PIN_INPUT | MUX_MODE0)        /* gpmc_d14.gpmc_d14 */
+                        OMAP3_CORE1_IOPAD(0x20ac, PIN_INPUT | MUX_MODE0)        /* gpmc_d15.gpmc_d15 */
+
+			/*
+			 * gpmc_ncs0, gpmc_nadv_ale, gpmc_noe, gpmc_nwe, gpmc_wait0 not muxable
+			 * according to TRM. REVISIT: why does nolo set input for gpmc_clk?
+			 */
+                        OMAP3_CORE1_IOPAD(0x20b0, PIN_OUTPUT | MUX_MODE0)       /* gpmc_ncs1.gpmc_ncs1 */
+                        OMAP3_CORE1_IOPAD(0x20be, PIN_INPUT | MUX_MODE0)        /* gpmc_clk.gpmc_clk */
+		>;
+	};
+
 	i2c1_pins: pinmux_i2c1_pins {
 		pinctrl-single,pins = <
 			0x18a (PIN_INPUT | MUX_MODE0)		/* i2c1_scl */
@@ -588,6 +615,8 @@
 	ranges = <0 0 0x04000000 0x10000000>; /* 256MB */
 	ranges = <0 0 0x01000000 0x01000000>,	/* 16 MB for OneNAND */
 		 <1 0 0x02000000 0x01000000>;	/* 16 MB for smc91c96 */
+	pinctrl-names = "default";
+	pinctrl-0 = <&gpmc_pins>;
 
 	/* gpio-irq for dma: 65 */
 
-- 
2.1.1