Nokia n900 problems in 3.18-rc1 (was Re: USB Ethernet gadget on Nokia n900)

[Tony Lindgren]

* Pavel Machek <pavel at ucw.cz> [141029 01:48]:
> 
> Speaking of testing:
> 
> I'm not sure what is omap_l3_smx neccessary for, but it does not work.
> 
> [    0.223297] omap_l3_smx omap_l3_smx.0: couldn't request debug irq
> [    0.223419] omap_l3_smx: probe of omap_l3_smx.0 failed with error
> -22

Hmm this should be fixed to get interrupts about invalid bus
access.
 
> There is some fun in pinmuxing:
> 
> [    0.247131] irq: no irq domain found for /ocp/pinmux at 48002030 !
> [    0.248291] irq: no irq domain found for /ocp/pinmux at 48002030 !
> ...
> [    0.384826] omap_i2c 48070000.i2c: could not find pctldev for node
> /ocp/pinmux at 48002030/pinmux_i\
> 2c1_pins, deferring probe
> [    0.384918] platform 48070000.i2c: Driver omap_i2c requests probe
> deferral
> [    0.385070] omap_i2c 48072000.i2c: could not find pctldev for node
> /ocp/pinmux at 48002030/pinmux_i\
> 2c2_pins, deferring probe
> [    0.385162] platform 48072000.i2c: Driver omap_i2c requests probe
> deferral
> [    0.385284] omap_i2c 48060000.i2c: could not find pctldev for node
> /ocp/pinmux at 48002030/pinmux_i\
> 2c3_pins, deferring probe
> [    0.385375] platform 48060000.i2c: Driver omap_i2c requests probe
> deferral

These are related to deferred probe and should go away when we
make drivers/i2c/busses/i2c-omap.c to use regular module_init and
stop using subsys_initcall. But I think legacy booting still needs
it early, could be omap1 only nowadays though.
 
> And serial has some problems:
> 
> [    0.482208] of_get_named_gpiod_flags: can't parse 'rts-gpio'
> property of node '/ocp/serial at 4806c\
> 000[0]'
> [    0.482513] omap_uart 4806c000.serial: ttyO1 at MMIO 0x4806c000
> (irq = 223, base_baud = 3000000)\
>  is a OMAP UART1
> [    0.484588] of_get_named_gpiod_flags: can't parse 'rts-gpio'
> property of node '/ocp/serial at 49020\
> 000[0]'
> [    0.484771] omap_uart 49020000.serial: ttyO2 at MMIO 0x49020000
> (irq = 224, base_baud = 3000000)\
>  is a OMAP UART2

I these come from the GPIO framework when booting with debug enabled.
 
> There's a lot of noise from probe defferal :-(. And it looks like mmc
> properties have some problems:
> 
> [    0.739349] of_get_named_gpiod_flags: can't parse 'wp-gpios'
> property of node '/ocp/mmc at 4809c000\
> [0]'
> [    0.740142] omap_hsmmc 4809c000.mmc: unable to get vmmc regulator
> -517
> [    0.740386] platform 4809c000.mmc: Driver omap_hsmmc requests probe
> deferral
> [    0.740661] of_get_named_gpiod_flags: can't parse 'cd-gpios'
> property of node '/ocp/mmc at 480b4000\
> [0]'
> [    0.740692] of_get_named_gpiod_flags: can't parse 'wp-gpios'
> property of node '/ocp/mmc at 480b4000\
> [0]'

These too. But yeah, I agree, let's try to patch away some of
the deferred probe noise.
 
> omapfb reports problems, but seems to work ok:
> 
> [    0.990386] omapfb omapfb: cannot parse default modes
> [    1.004791] Console: switching to colour frame buffer device 100x30
> [    1.073150] omapfb omapfb: using display 'lcd' mode 800x480

Tomi, is the default mode warning correct here?

Regards,

Tony