[PATCH v4 2/2] ARM: dts: add initial support for TBS2910 Matrix ARM mini PC
Soeren Moch
smoch at web.de
Mon Oct 27 12:10:51 PDT 2014
TBS2910 is a i.MX6Q based board. For additional details refer to
http://www.tbsdtv.com/products/tbs2910-matrix-arm-mini-pc.html
Signed-off-by: Soeren Moch <smoch at web.de>
Reviewed-by: Sebastian Hesselbarth <sebastian.hesselbarth at gmail.com>
---
Cc: Sebastian Hesselbarth <sebastian.hesselbarth at gmail.com>
Cc: Shawn Guo <shawn.guo at linaro.org>
Cc: Sascha Hauer <kernel at pengutronix.de>
Cc: Fabio Estevam <festevam at gmail.com>
Changes in v2:
- add tbs vendor prefix to vendor-prefixes.txt
- use GPIO_ACTIVE_{HIGH,LOW}
- add led label and default-state="keep"
- whitespace cleanup
Changes in v3:
- split vendor prefix addition into separate patch
- dual-licensed: GPL or X11
- move iomuxc node to the bottom to improve readability
- remove snvs_poweroff node, not in mainline yet
- whitespace cleanup, hope I got it right now
Changes in v4:
- remove 'regulator-always-on' properties
- remove pinctrl hog_grp and add pins to associated peripheral nodes
- configure pad control settings for all used pins
---
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/imx6q-tbs2910.dts | 429 ++++++++++++++++++++++++++++++++++++
2 files changed, 430 insertions(+)
create mode 100644 arch/arm/boot/dts/imx6q-tbs2910.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index b8c5cd3..f6ad478 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -230,6 +230,7 @@ dtb-$(CONFIG_ARCH_MXC) += \
imx6q-sabrelite.dtb \
imx6q-sabresd.dtb \
imx6q-sbc6x.dtb \
+ imx6q-tbs2910.dtb \
imx6q-udoo.dtb \
imx6q-wandboard.dtb \
imx6q-wandboard-revb1.dtb \
diff --git a/arch/arm/boot/dts/imx6q-tbs2910.dts b/arch/arm/boot/dts/imx6q-tbs2910.dts
new file mode 100644
index 0000000..d2a5743
--- /dev/null
+++ b/arch/arm/boot/dts/imx6q-tbs2910.dts
@@ -0,0 +1,429 @@
+/*
+ * Copyright 2014 Soeren Moch <smoch at web.de>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public
+ * License along with this file; if not, write to the Free
+ * Software Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+
+#include "imx6q.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+ model = "TBS2910 Matrix ARM mini PC";
+ compatible = "tbs,imx6q-tbs2910", "fsl,imx6q";
+
+ chosen {
+ stdout-path = &uart1;
+ };
+
+ memory {
+ reg = <0x10000000 0x80000000>;
+ };
+
+ fan {
+ compatible = "gpio-fan";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gpio_fan>;
+ gpios = <&gpio3 28 GPIO_ACTIVE_HIGH>;
+ gpio-fan,speed-map = <0 0
+ 3000 1>;
+ };
+
+ ir_recv {
+ compatible = "gpio-ir-receiver";
+ gpios = <&gpio3 18 GPIO_ACTIVE_LOW>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ir>;
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gpio_leds>;
+
+ blue {
+ label = "blue_status_led";
+ gpios = <&gpio1 2 GPIO_ACTIVE_HIGH>;
+ default-state = "keep";
+ };
+ };
+
+ regulators {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ reg_2p5v: regulator at 0 {
+ compatible = "regulator-fixed";
+ reg = <0>;
+ regulator-name = "2P5V";
+ regulator-min-microvolt = <2500000>;
+ regulator-max-microvolt = <2500000>;
+ };
+
+ reg_3p3v: regulator at 1 {
+ compatible = "regulator-fixed";
+ reg = <1>;
+ regulator-name = "3P3V";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ reg_5p0v: regulator at 2 {
+ compatible = "regulator-fixed";
+ reg = <2>;
+ regulator-name = "5P0V";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ };
+ };
+
+ sound-sgtl5000 {
+ audio-codec = <&sgtl5000>;
+ audio-routing =
+ "MIC_IN", "Mic Jack",
+ "Mic Jack", "Mic Bias",
+ "Headphone Jack", "HP_OUT";
+ compatible = "fsl,imx-audio-sgtl5000";
+ model = "On-board Codec";
+ mux-ext-port = <3>;
+ mux-int-port = <1>;
+ ssi-controller = <&ssi1>;
+ };
+
+ sound-spdif {
+ compatible = "fsl,imx-audio-spdif";
+ model = "On-board SPDIF";
+ spdif-controller = <&spdif>;
+ spdif-out;
+ };
+};
+
+&audmux {
+ status = "okay";
+};
+
+&fec {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_enet>;
+ phy-mode = "rgmii";
+ phy-reset-gpios = <&gpio1 25 GPIO_ACTIVE_HIGH>;
+ status = "okay";
+};
+
+&hdmi {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_hdmi>;
+ ddc-i2c-bus = <&i2c2>;
+ status = "okay";
+};
+
+&i2c1 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c1>;
+ status = "okay";
+
+ sgtl5000: sgtl5000 at 0a {
+ clocks = <&clks 201>;
+ compatible = "fsl,sgtl5000";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_sgtl5000>;
+ reg = <0x0a>;
+ VDDA-supply = <®_2p5v>;
+ VDDIO-supply = <®_3p3v>;
+ };
+};
+
+&i2c2 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c2>;
+ status = "okay";
+};
+
+&i2c3 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c3>;
+ status = "okay";
+
+ rtc: ds1307 at 68 {
+ compatible = "dallas,ds1307";
+ reg = <0x68>;
+ };
+};
+
+&pcie {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pcie>;
+ reset-gpio = <&gpio7 12 GPIO_ACTIVE_HIGH>;
+ status = "okay";
+};
+
+&sata {
+ status = "okay";
+};
+
+&spdif {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_spdif>;
+ status = "okay";
+};
+
+&ssi1 {
+ fsl,mode = "i2s-slave";
+ status = "okay";
+};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart1>;
+ status = "okay";
+};
+
+&uart2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart2>;
+ status = "okay";
+};
+
+&usbh1 {
+ vbus-supply = <®_5p0v>;
+ status = "okay";
+};
+
+&usbotg {
+ vbus-supply = <®_5p0v>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usbotg>;
+ disable-over-current;
+ status = "okay";
+};
+
+&usdhc2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usdhc2>;
+ bus-width = <4>;
+ cd-gpios = <&gpio2 2 GPIO_ACTIVE_HIGH>;
+ vmmc-supply = <®_3p3v>;
+ status = "okay";
+};
+
+&usdhc3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usdhc3>;
+ bus-width = <4>;
+ cd-gpios = <&gpio2 0 GPIO_ACTIVE_HIGH>;
+ wp-gpios = <&gpio2 1 GPIO_ACTIVE_HIGH>;
+ vmmc-supply = <®_3p3v>;
+ status = "okay";
+};
+
+&usdhc4 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usdhc4>;
+ bus-width = <8>;
+ non-removable;
+ no-1-8-v;
+ status = "okay";
+};
+
+&iomuxc {
+ imx6q-tbs2910 {
+ pinctrl_enet: enetgrp {
+ fsl,pins = <
+ MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x1b0b0
+ MX6QDL_PAD_ENET_MDC__ENET_MDC 0x1b0b0
+ MX6QDL_PAD_RGMII_TXC__RGMII_TXC 0x1b0b0
+ MX6QDL_PAD_RGMII_TD0__RGMII_TD0 0x1b0b0
+ MX6QDL_PAD_RGMII_TD1__RGMII_TD1 0x1b0b0
+ MX6QDL_PAD_RGMII_TD2__RGMII_TD2 0x1b0b0
+ MX6QDL_PAD_RGMII_TD3__RGMII_TD3 0x1b0b0
+ MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL 0x1b0b0
+ MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK 0x1b0b0
+ MX6QDL_PAD_RGMII_RXC__RGMII_RXC 0x1b0b0
+ MX6QDL_PAD_RGMII_RD0__RGMII_RD0 0x1b0b0
+ MX6QDL_PAD_RGMII_RD1__RGMII_RD1 0x1b0b0
+ MX6QDL_PAD_RGMII_RD2__RGMII_RD2 0x1b0b0
+ MX6QDL_PAD_RGMII_RD3__RGMII_RD3 0x1b0b0
+ MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL 0x1b0b0
+ MX6QDL_PAD_GPIO_16__ENET_REF_CLK 0x4001b0a8
+ MX6QDL_PAD_ENET_CRS_DV__GPIO1_IO25 0x1b059
+ >;
+ };
+
+ pinctrl_hdmi: hdmigrp {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_ROW2__HDMI_TX_CEC_LINE 0x1f8b0
+ >;
+ };
+
+ pinctrl_i2c1: i2c1grp {
+ fsl,pins = <
+ MX6QDL_PAD_CSI0_DAT9__I2C1_SCL 0x4001b8b1
+ MX6QDL_PAD_CSI0_DAT8__I2C1_SDA 0x4001b8b1
+ >;
+ };
+
+ pinctrl_i2c2: i2c2grp {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_COL3__I2C2_SCL 0x4001b8b1
+ MX6QDL_PAD_KEY_ROW3__I2C2_SDA 0x4001b8b1
+ >;
+ };
+
+ pinctrl_i2c3: i2c3grp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_3__I2C3_SCL 0x4001b8b1
+ MX6QDL_PAD_GPIO_6__I2C3_SDA 0x4001b8b1
+ >;
+ };
+
+ pinctrl_ir: irgrp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D18__GPIO3_IO18 0x17059
+ >;
+ };
+
+ pinctrl_pcie: pciegrp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_17__GPIO7_IO12 0x17059
+ >;
+ };
+
+ pinctrl_sgtl5000: sgtl5000grp {
+ fsl,pins = <
+ MX6QDL_PAD_CSI0_DAT7__AUD3_RXD 0x130b0
+ MX6QDL_PAD_CSI0_DAT4__AUD3_TXC 0x130b0
+ MX6QDL_PAD_CSI0_DAT5__AUD3_TXD 0x110b0
+ MX6QDL_PAD_CSI0_DAT6__AUD3_TXFS 0x130b0
+ MX6QDL_PAD_GPIO_0__CCM_CLKO1 0x130b0
+ >;
+ };
+
+ pinctrl_spdif: spdifgrp {
+ fsl,pins = <MX6QDL_PAD_GPIO_19__SPDIF_OUT 0x13091
+ >;
+ };
+
+ pinctrl_uart1: uart1grp {
+ fsl,pins = <
+ MX6QDL_PAD_CSI0_DAT10__UART1_TX_DATA 0x1b0b1
+ MX6QDL_PAD_CSI0_DAT11__UART1_RX_DATA 0x1b0b1
+ >;
+ };
+
+ pinctrl_uart2: uart2grp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D26__UART2_TX_DATA 0x1b0b1
+ MX6QDL_PAD_EIM_D27__UART2_RX_DATA 0x1b0b1
+ >;
+ };
+
+ pinctrl_usbotg: usbotggrp {
+ fsl,pins = <
+ MX6QDL_PAD_ENET_RX_ER__USB_OTG_ID 0x17059
+ >;
+ };
+
+ pinctrl_usdhc2: usdhc2grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD2_CMD__SD2_CMD 0x17059
+ MX6QDL_PAD_SD2_CLK__SD2_CLK 0x10059
+ MX6QDL_PAD_SD2_DAT0__SD2_DATA0 0x17059
+ MX6QDL_PAD_SD2_DAT1__SD2_DATA1 0x17059
+ MX6QDL_PAD_SD2_DAT2__SD2_DATA2 0x17059
+ MX6QDL_PAD_SD2_DAT3__SD2_DATA3 0x17059
+ MX6QDL_PAD_NANDF_D2__GPIO2_IO02 0x17059
+ >;
+ };
+
+ pinctrl_usdhc3: usdhc3grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD3_CMD__SD3_CMD 0x17059
+ MX6QDL_PAD_SD3_CLK__SD3_CLK 0x10059
+ MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x17059
+ MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x17059
+ MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x17059
+ MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x17059
+ MX6QDL_PAD_NANDF_D0__GPIO2_IO00 0x17059
+ MX6QDL_PAD_NANDF_D1__GPIO2_IO01 0x17059
+ >;
+ };
+
+ pinctrl_usdhc4: usdhc4grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD4_CMD__SD4_CMD 0x17059
+ MX6QDL_PAD_SD4_CLK__SD4_CLK 0x10059
+ MX6QDL_PAD_SD4_DAT0__SD4_DATA0 0x17059
+ MX6QDL_PAD_SD4_DAT1__SD4_DATA1 0x17059
+ MX6QDL_PAD_SD4_DAT2__SD4_DATA2 0x17059
+ MX6QDL_PAD_SD4_DAT3__SD4_DATA3 0x17059
+ MX6QDL_PAD_SD4_DAT4__SD4_DATA4 0x17059
+ MX6QDL_PAD_SD4_DAT5__SD4_DATA5 0x17059
+ MX6QDL_PAD_SD4_DAT6__SD4_DATA6 0x17059
+ MX6QDL_PAD_SD4_DAT7__SD4_DATA7 0x17059
+ >;
+ };
+ };
+
+ gpio_fan {
+ pinctrl_gpio_fan: gpiofangrp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D28__GPIO3_IO28 0x130b1
+ >;
+ };
+ };
+
+ gpio_leds {
+ pinctrl_gpio_leds: gpioledsgrp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_2__GPIO1_IO02 0x130b1
+ >;
+ };
+ };
+};
--
1.9.1
More information about the linux-arm-kernel
mailing list