[PATCH 0/9] Marvell PXA168 libphy handling and Berlin Ethernet

[Florian Fainelli]

Hi Sebastian,

On 10/21/2014 01:53 AM, Sebastian Hesselbarth wrote:
> This patch series deals with a removing a IP feature that can be found
> on all currently supported Marvell Ethernet IP (pxa168_eth, mv643xx_eth,
> mvneta). The MAC IP allows to automatically perform PHY auto-negotiation
> without software interaction.
> 
> However, this feature (a) fundamentally clashes with the way libphy works
> and (b) is unable to deal with quirky PHYs that require special treatment.
> In this series, pxa168_eth driver is rewritten to completely disable that
> feature and properly deal with libphy provided PHYs.
> 
> This is the real patch set after an RFT sent earlier. Unfortunately, there
> was no testing from MMP/gplug but there was for BG2Q. However, it still
> would be great to get a Tested-by on gplug. Also, this patch set is now
> rebased on v3.18-rc1. As usual, a branch on top of v3.18-rc1 can be found at
> 
> git://git.infradead.org/users/hesselba/linux-berlin.git devel/bg2-bg2cd-eth-v1
> 
> Patches 1-5 should go through David's net tree, I'll pick up the DT patches
> 6-9.
> 
> Compared to the RFT, there have been some changes:
> - added phy-connection-type property to BG2Q PHY DT node
> - bail out from pxa168_eth_adjust_link when there is no change in
>   PHY parameters. Also, add a call to phy_print_status.
> 
> Patch 1 adds support for Marvell 88E3016 FastEthernet PHY that is also
> integrated in Marvell Berlin BG2/BG2CD SoCs.
> 
> Patch 2 allows to pass phy_interface_t on pxa168_eth platform_data that
> is only used by mach-mmp/gplug. From the board setup, I guessed gplug's
> PHY is connected via RMII. The patch still isn't even compile tested.
> 
> Patches 3-5 prepare proper libphy handling and finally remove all in-driver
> PHY mangling related to the feature explained above.
> 
> Patches 6-9 add corresponding ethernet DT nodes to BG2, BG2CD, add a
> phy-connection-type property to BG2Q and enable ethernet on BG2-based Sony
> NSZ-GS7. I have tested all this on GS7 successfully with ip=dhcp on 100M FD.

Besides the misplacement of the 'phy-connection-type' as reported by
Sergei, this looks good to me:

Reviewed-by: Florian Fainelli <f.fainelli at gmail.com>

Thanks!

> 
> Antoine Ténart (1):
>   ARM: berlin: Add phy-connection-type to BG2Q PHY
> 
> Sebastian Hesselbarth (8):
>   phy: marvell: Add support for 88E3016 FastEthernet PHY
>   net: pxa168_eth: Provide phy_interface mode on platform_data
>   net: pxa168_eth: Prepare proper libphy handling
>   net: pxa168_eth: Remove HW auto-negotiaion
>   net: pxa168_eth: Remove in-driver PHY mangling
>   ARM: berlin: Add BG2 ethernet DT nodes
>   ARM: berlin: Add BG2CD ethernet DT nodes
>   ARM: berlin: Enable ethernet on Sony NSZ-GS7
> 
>  arch/arm/boot/dts/berlin2-sony-nsz-gs7.dts |   2 +
>  arch/arm/boot/dts/berlin2.dtsi             |  36 +++++
>  arch/arm/boot/dts/berlin2cd.dtsi           |  36 +++++
>  arch/arm/boot/dts/berlin2q.dtsi            |   1 +
>  arch/arm/mach-mmp/gplugd.c                 |   2 +
>  drivers/net/ethernet/marvell/pxa168_eth.c  | 248 ++++++++++++-----------------
>  drivers/net/phy/marvell.c                  |  46 ++++++
>  include/linux/marvell_phy.h                |   1 +
>  include/linux/pxa168_eth.h                 |   1 +
>  9 files changed, 225 insertions(+), 148 deletions(-)
> 
> ---
> Cc: "David S. Miller" <davem at davemloft.net>
> Cc: "Antoine Ténart" <antoine.tenart at free-electrons.com>
> Cc: Florian Fainelli <f.fainelli at gmail.com>
> Cc: Eric Miao <eric.y.miao at gmail.com>
> Cc: Haojian Zhuang <haojian.zhuang at gmail.com>
> Cc: linux-arm-kernel at lists.infradead.org
> Cc: netdev at vger.kernel.org
> Cc: devicetree at vger.kernel.org
> Cc: linux-kernel at vger.kernel.org
>