[PATCH] [RFC] ARM: shmobile: Add early debugging support using SCIF(A)
Laurent Pinchart
laurent.pinchart at ideasonboard.com
Sun Oct 5 15:18:00 PDT 2014
Hi Geert,
Thank you for the patch.
It looks like you've beaten Ian Molton (CC'ed) on this, he was planning to
send exactly the same thing.
On Thursday 02 October 2014 21:02:43 Geert Uytterhoeven wrote:
> Add serial port debug macros for the SCIF(A) serial ports.
> This includes all shmobile SoCs, except for EMEV2.
>
> On SoCs using the legacy machine_desc.map_io(), an identity mapping of
> the SCIF(A) registers must be set up in .map_io(). On all but r8a7779
> this was already done.
>
> On other SoCs, debug_ll_io_init() maps the SCIF(A) registers to a fixed
> virtual address. 0xfdxxxxxx was chosen, as it should lie below
> VMALLOC_END = 0xff000000, and must not conflict with the 2 MiB reserved
> region at PCI_IO_VIRT_BASE = 0xfee00000.
>
> This was derived from the r8a7790 version by Laurent Pinchart.
>
> Signed-off-by: Geert Uytterhoeven <geert+renesas at glider.be>
> ---
> Tested on r8a7791/koelsch and r8a7740/armadillo.
> Testing on other platforms would be highly appreciated.
>
> Notes:
> - On armadillo-multiplatform there may be a period while garbage data
> is output.
> This happens because sh_mobile_i2c_init() enables and disables its
> clock during probing. As iic0 and scifa1 share the same parent
> clock, this causes the scifa1 clock to no longer receive clock
> ticks.
> On armadillo-legacy, this is mitigated by the pre-CCF clock driver,
> which never really disables clocks during boot-up for exactly this
> reason. Cfr. "One example of this is the handling of the Mackerel
> serial console output that shares clock with the I2C controller.",
> in commit 794d78fea51504ba ("drivers: sh: late disabling of clocks
> V2").
> I'm wondering whether this can be fixed in the i2c driver? Does it
> really have to enable and disable the clock?
Do you think it be possible to enable the required clock dynamically in setup
code when CONFIG_DEBUG_LL is enabled ?
> - While the serial console on r8a7790 was switched from SCIF0 to
> SCIFA0 recently, I believe r8a7990 still needs to use SCIF0 instead
> of SCIFA0, as that's what the bootloader has configured.
Good point. Wolfram, any opinion about this ?
> ---
> arch/arm/Kconfig.debug | 20 +++++++++++-
> arch/arm/include/debug/scif.S | 60 +++++++++++++++++++++++++++++++
> arch/arm/mach-shmobile/setup-r8a7779.c | 7 ++++
> 3 files changed, 86 insertions(+), 1 deletion(-)
> create mode 100644 arch/arm/include/debug/scif.S
>
> diff --git a/arch/arm/Kconfig.debug b/arch/arm/Kconfig.debug
> index b11ad54f8d17fa6b..58ace40b30938e58 100644
> --- a/arch/arm/Kconfig.debug
> +++ b/arch/arm/Kconfig.debug
> @@ -699,6 +699,14 @@ choice
> their output to UART 2. The port must have been initialised
> by the boot-loader before use.
>
> + config DEBUG_SCIF
How about calling this DEBUG_RENESAS_SCIF ? Other platforms use the platform
name instead of the serial IP core name.
> + bool "Kernel low-level debugging messages via SCIF(A) on Renesas ARM
> SoCs"
> + depends on ARCH_R7S72100 || ARCH_RCAR_GEN1 || ARCH_RCAR_GEN2 ||
> ARCH_RMOBILE
> + help
> + Say Y here if you want kernel low-level debugging support
> + on Renesas ARM based platforms using SCIF(A) serial ports
> + (SH-Mobile, R-Mobile, RZ/A1H, R-Car Gen1, R-Car Gen2).
> +
> config DEBUG_SOCFPGA_UART
> depends on ARCH_SOCFPGA
> bool "Use SOCFPGA UART for low-level debug"
> @@ -1028,6 +1036,7 @@ config DEBUG_LL_INCLUDE
> DEBUG_IMX6SX_UART
> default "debug/msm.S" if DEBUG_MSM_UART || DEBUG_QCOM_UARTDM
> default "debug/omap2plus.S" if DEBUG_OMAP2PLUS_UART
> + default "debug/scif.S" if DEBUG_SCIF
Similarly, renesas-scif.S ?
> default "debug/s3c24xx.S" if DEBUG_S3C24XX_UART
> default "debug/s5pv210.S" if DEBUG_S5PV210_UART
> default "debug/sirf.S" if DEBUG_SIRFPRIMA2_UART1 || DEBUG_SIRFMARCO_UART1
> @@ -1109,6 +1118,12 @@ config DEBUG_UART_PHYS
> default 0xd4017000 if DEBUG_MMP_UART2
> default 0xd4018000 if DEBUG_MMP_UART3
> default 0xe0000000 if ARCH_SPEAR13XX
> + default 0xe6c40000 if DEBUG_SCIF && (ARCH_R8A73A4 || ARCH_SH7372)
> + default 0xe6c50000 if DEBUG_SCIF && ARCH_R8A7740
> + default 0xe6c80000 if DEBUG_SCIF && ARCH_SH73A0
> + default 0xe6e58000 if DEBUG_SCIF && ARCH_R8A7794
> + default 0xe6e60000 if DEBUG_SCIF && (ARCH_R8A7790 || ARCH_R8A7791 ||
> ARCH_R8A7793) + default 0xe8008000 if DEBUG_SCIF && ARCH_R7S72100
> default 0xf0000be0 if ARCH_EBSA110
> default 0xf1012000 if DEBUG_MVEBU_UART_ALTERNATE
> default 0xf1012000 if ARCH_DOVE || ARCH_MV78XX0 || \
> @@ -1121,12 +1136,15 @@ config DEBUG_UART_PHYS
> default 0xff690000 if DEBUG_RK32_UART2
> default 0xffc02000 if DEBUG_SOCFPGA_UART
> default 0xffd82340 if ARCH_IOP13XX
> + default 0xffe40000 if DEBUG_SCIF && ARCH_R8A7778
> + default 0xffe42000 if DEBUG_SCIF && ARCH_R8A7779
> default 0xfff36000 if DEBUG_HIGHBANK_UART
> default 0xfffff700 if ARCH_IOP33X
> depends on DEBUG_LL_UART_8250 || DEBUG_LL_UART_PL01X || \
> DEBUG_LL_UART_EFM32 || \
> DEBUG_UART_8250 || DEBUG_UART_PL01X || \
> - DEBUG_MSM_UART || DEBUG_QCOM_UARTDM || DEBUG_S3C24XX_UART
> + DEBUG_MSM_UART || DEBUG_QCOM_UARTDM || DEBUG_S3C24XX_UART || \
> + DEBUG_SCIF
>
> config DEBUG_UART_VIRT
> hex "Virtual base address of debug UART"
> diff --git a/arch/arm/include/debug/scif.S b/arch/arm/include/debug/scif.S
> new file mode 100644
> index 0000000000000000..9c9b9b2c17f97b4a
> --- /dev/null
> +++ b/arch/arm/include/debug/scif.S
> @@ -0,0 +1,60 @@
> +/*
> + * Renesas SCIF(A) debugging macro include header
> + *
> + * Based on r8a7790.S
> + *
> + * Copyright (C) 2012-2013 Renesas Electronics Corporation
2014 ?
> + * Copyright (C) 1994-1999 Russell King
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License version 2 as
> + * published by the Free Software Foundation.
> + */
> +
> +#if CONFIG_DEBUG_UART_PHYS < 0xe6e00000
> +/* SCIFA */
> +#define FTDR 0x20
> +#define FSR 0x14
> +#else
> +/* SCIF */
> +#define FTDR 0x0c
> +#define FSR 0x10
> +#endif
> +
> +#define SCIF_PHYS CONFIG_DEBUG_UART_PHYS
> +
> +#if defined(CONFIG_ARCH_R8A7740) || defined(CONFIG_ARCH_R8A7779) || \
> + defined(CONFIG_ARCH_SH7372) || defined(CONFIG_ARCH_SH73A0)
> +/* Legacy machine_desc.map_io() sets up an identity mapping for us */
> +#define SCIF_VIRT SCIF_PHYS
> +#else
> +/* Relying on debug_ll_io_init(), so we have to select a free gap ourselves
> */
> +#define SCIF_VIRT ((SCIF_PHYS & 0x00ffffff) | 0xfd000000)
> +#endif
> +
> +#define TDFE (1 << 5)
> +#define TEND (1 << 6)
> +
> + .macro addruart, rp, rv, tmp
> + ldr \rp, =SCIF_PHYS
> + ldr \rv, =SCIF_VIRT
> + .endm
> +
> + .macro waituart, rd, rx
> +1001: ldrh \rd, [\rx, #FSR]
> + tst \rd, #TDFE
> + beq 1001b
> + .endm
> +
> + .macro senduart, rd, rx
> + strb \rd, [\rx, #FTDR]
> + ldrh \rd, [\rx, #FSR]
> + bic \rd, \rd, #TEND
> + strh \rd, [\rx, #FSR]
> + .endm
> +
> + .macro busyuart, rd, rx
> +1001: ldrh \rd, [\rx, #FSR]
> + tst \rd, #TEND
> + beq 1001b
> + .endm
> diff --git a/arch/arm/mach-shmobile/setup-r8a7779.c
> b/arch/arm/mach-shmobile/setup-r8a7779.c index
> 136078ab9407cc2d..24c49f7121d69d28 100644
> --- a/arch/arm/mach-shmobile/setup-r8a7779.c
> +++ b/arch/arm/mach-shmobile/setup-r8a7779.c
> @@ -66,6 +66,13 @@ static struct map_desc r8a7779_io_desc[] __initdata = {
> .length = SZ_16M,
> .type = MT_DEVICE_NONSHARED
> },
> + /* 64K entity map for 0xffe40000 (SCIF0/1) */
> + {
> + .virtual = 0xffe40000,
> + .pfn = __phys_to_pfn(0xffe40000),
> + .length = SZ_64K,
> + .type = MT_DEVICE_NONSHARED
> + },
Should we guard that with #ifdef CONFIG_DEBUG_LL ?
> };
>
> void __init r8a7779_map_io(void)
--
Regards,
Laurent Pinchart
More information about the linux-arm-kernel
mailing list