[PATCH v2 RESEND 1/2] ARM: vexpress: Remove non-DT code

[Pawel Moll]

On Fri, 2014-11-28 at 15:30 +0000, Russell King - ARM Linux wrote:
> mmci-pl18x 10005000.mmci: no support for card's volts
> mmc0: error -22 whilst initialising SD card

Just tried it again:

--8<----------------------------
ARM Versatile Express Boot Monitor
Version:    V5.2.1
Build Date: Apr  4 2013
Daughterboard Site 1: V2P-CA9 Cortex A9
Daughterboard Site 2: Not Used
Running boot script from flash - BOOTSCRIPT
Loaded FDT - ca9
Loaded initrd - busybox
Copied 0x400000 bytes from 0x48000000 to 0x60008000
Booting kernel @ 0x60008000
Command line 'console=ttyAMA0,38400 earlyprintk debug '
initrd @ 0x70000000 (4127012 bytes)
FDT @ 0x69000000 (14048 bytes)
Uncompressing Linux... done, booting the kernel.
Booting Linux on physical CPU 0x0
Initializing cgroup subsys cpuset
Linux version 3.18.0-rc6+ (pawmol01 at hornet) (gcc version 4.9.2 20140904 (prerelease) (crosstool-NG linaro-1.13.1-4.9-2014.09 - Linaro GCC 4.9-2014.09) ) #1442 SMP Mon Nov 24 16:43:30 GMT 2014
CPU: ARMv7 Processor [410fc091] revision 1 (ARMv7), cr=10c5387d
CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
Machine model: V2P-CA9
bootconsole [earlycon0] enabled
[...]
mmci-pl18x 10005000.mmci: Got CD GPIO
mmci-pl18x 10005000.mmci: Got WP GPIO
mmci-pl18x 10005000.mmci: Looking up vmmc-supply from device tree
mmci-pl18x 10005000.mmci: Looking up vqmmc-supply from device tree
mmci-pl18x 10005000.mmci: Looking up vqmmc-supply property in node /smb/motherboard/iofpga at 7,00000000/mmci at 05000 failed
mmci-pl18x 10005000.mmci: No vqmmc regulator found
mmci-pl18x 10005000.mmci: mmc0: PL180 manf 41 rev0 at 0x10005000 irq 41,42 (pio)
[...]
mmc0: new SD card at address 88f7
mmcblk0: mmc0:88f7 SD02G 1.84 GiB 
 mmcblk0: p1 p2
[...]
/ # mount /dev/mmcblk0p2 /mnt
EXT2-fs (mmcblk0p2): warning: mounting unchecked fs, running e2fsck is recommended
--8<------------------------------------

vmmc-supply is a defined as:

				vmmc-supply = <&v2m_fixed_3v3>;

which is:

                v2m_fixed_3v3: fixedregulator at 0 {
                        compatible = "regulator-fixed";

and arch/arm/mach-vexpress/Kconfig says:

menuconfig ARCH_VEXPRESS
[...]
        select REGULATOR_FIXED_VOLTAGE if REGULATOR

but it doesn't select REGULATOR in result of this discussion:

http://thread.gmane.org/gmane.linux.ports.arm.kernel/223426/focus=223427

To summarize, I believe that setting CONFIG_REGULATOR=y (as in
vexpress_defconfig) should solve your issue.

Pawel