[PATCH v2 2/5] i2c: davinci: query STP always when NACK is received

[Grygorii Strashko]

According to I2C specification the NACK should be handled as folows:
"When SDA remains HIGH during this ninth clock pulse, this is defined as the Not
Acknowledge signal. The master can then generate either a STOP condition to
abort the transfer, or a repeated START condition to start a new transfer."
[I2C spec Rev. 6, 3.1.6: http://www.nxp.com/documents/user_manual/UM10204.pdf]

Currently the Davinci i2c driver interrupts the transfer on receipt of a
NACK but fails to send a STOP in some situations and so makes the bus
stuck until next I2C IP reset (idle/enable).

For example, the issue will happen during SMBus read transfer which
consists from two i2c messages write command/address and read data:

S Slave Address Wr A Command Code A Sr Slave Address Rd A D1..Dn A P
<--- write -----------------------> <--- read --------------------->

The I2C client device will send NACK if it can't recognize "Command Code"
and it's expected from I2C master to query STP in this case.
But now, Davinci i2C driver will just exit with -EREMOTEIO and STP will
not be queried.

Hence, fix it by querying Stop condition (STP) always when NACK is received.

This patch fixes Davinci I2C in the same way it was done for OMAP I2C
commit cda2109a26eb ("i2c: omap: query STP always when NACK is received").

CC: Sekhar Nori <nsekhar at ti.com>
CC: Kevin Hilman <khilman at deeprootsystems.com>
CC: Santosh Shilimkar <ssantosh at kernel.org>
CC: Murali Karicheri <m-karicheri2 at ti.com>
Reported-by: Hein Tibosch <hein_tibosch at yahoo.es>
Signed-off-by: Grygorii Strashko <grygorii.strashko at ti.com>
---
 drivers/i2c/busses/i2c-davinci.c | 8 +++-----
 1 file changed, 3 insertions(+), 5 deletions(-)

diff --git a/drivers/i2c/busses/i2c-davinci.c b/drivers/i2c/busses/i2c-davinci.c
index 7f54903..1990ae8 100644
--- a/drivers/i2c/busses/i2c-davinci.c
+++ b/drivers/i2c/busses/i2c-davinci.c
@@ -411,11 +411,9 @@ i2c_davinci_xfer_msg(struct i2c_adapter *adap, struct i2c_msg *msg, int stop)
 	if (dev->cmd_err & DAVINCI_I2C_STR_NACK) {
 		if (msg->flags & I2C_M_IGNORE_NAK)
 			return msg->len;
-		if (stop) {
-			w = davinci_i2c_read_reg(dev, DAVINCI_I2C_MDR_REG);
-			w |= DAVINCI_I2C_MDR_STP;
-			davinci_i2c_write_reg(dev, DAVINCI_I2C_MDR_REG, w);
-		}
+		w = davinci_i2c_read_reg(dev, DAVINCI_I2C_MDR_REG);
+		w |= DAVINCI_I2C_MDR_STP;
+		davinci_i2c_write_reg(dev, DAVINCI_I2C_MDR_REG, w);
 		return -EREMOTEIO;
 	}
 	return -EIO;
-- 
1.9.1