[PATCH 4/5] ARM: dts: sun6i: Add sun6i-a31s.dtsi
Chen-Yu Tsai
wens at csie.org
Tue Nov 25 15:45:10 PST 2014
On Wed, Nov 26, 2014 at 2:18 AM, Maxime Ripard
<maxime.ripard at free-electrons.com> wrote:
> Hi,
>
> On Sun, Nov 23, 2014 at 01:54:42PM +0100, Hans de Goede wrote:
>> Add a dtsi file for A31s based boards. This is a copy of sun6i-a31.dtsi, with:
>>
>> -The main pinctrl compatible changed to allwinner,sun6i-a31s.dtsi
>> -The ohci2 controller is present according to the data-sheet, but not routed
>> to the outside, so remove it from the dtsi as having an always disabled node
>> is not useful.
>>
>> All the other nodes present in the original sun6i-a31.dtsi are present in
>> the A31s too, and are 100% compatible.
>
> Then maybe duplicating the DT isn't worth it then.
>
> Creating a sun6i.dtsi and including that from both the A31 and A31s
> seems more like an appropriate solution.
>
>>
>> Signed-off-by: Hans de Goede <hdegoede at redhat.com>
>> ---
>> arch/arm/boot/dts/sun6i-a31s.dtsi | 925 ++++++++++++++++++++++++++++++++++++++
>> 1 file changed, 925 insertions(+)
>> create mode 100644 arch/arm/boot/dts/sun6i-a31s.dtsi
>>
>> diff --git a/arch/arm/boot/dts/sun6i-a31s.dtsi b/arch/arm/boot/dts/sun6i-a31s.dtsi
>> new file mode 100644
>> index 0000000..b3b99a9
>> --- /dev/null
>> +++ b/arch/arm/boot/dts/sun6i-a31s.dtsi
>> @@ -0,0 +1,925 @@
>> +/*
>> + * Copyright 2013 Maxime Ripard
>> + *
>> + * Maxime Ripard <maxime.ripard at free-electrons.com>
>
> It should be your copyright here.
>
>> + *
>> + * This file is dual-licensed: you can use it either under the terms
>> + * of the GPL or the X11 license, at your option. Note that this dual
>> + * licensing only applies to this file, and not this project as a
>> + * whole.
>> + *
>> + * a) This library is free software; you can redistribute it and/or
>> + * modify it under the terms of the GNU General Public License as
>> + * published by the Free Software Foundation; either version 2 of the
>> + * License, or (at your option) any later version.
>> + *
>> + * This library is distributed in the hope that it will be useful,
>> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
>> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
>> + * GNU General Public License for more details.
>> + *
>> + * You should have received a copy of the GNU General Public
>> + * License along with this library; if not, write to the Free
>> + * Software Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
>> + * MA 02110-1301 USA
>
> There was an issue with the wording of the license, s/library/file/
>
>> + *
>> + * Or, alternatively,
>> + *
>> + * b) Permission is hereby granted, free of charge, to any person
>> + * obtaining a copy of this software and associated documentation
>> + * files (the "Software"), to deal in the Software without
>> + * restriction, including without limitation the rights to use,
>> + * copy, modify, merge, publish, distribute, sublicense, and/or
>> + * sell copies of the Software, and to permit persons to whom the
>> + * Software is furnished to do so, subject to the following
>> + * conditions:
>> + *
>> + * The above copyright notice and this permission notice shall be
>> + * included in all copies or substantial portions of the Software.
>> + *
>> + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
>> + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
>> + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
>> + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
>> + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
>> + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
>> + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
>> + * OTHER DEALINGS IN THE SOFTWARE.
>> + */
>> +
>> +/include/ "skeleton.dtsi"
>> +
>> +/ {
>> + interrupt-parent = <&gic>;
>> +
>> + aliases {
>> + serial0 = &uart0;
>> + serial1 = &uart1;
>> + serial2 = &uart2;
>> + serial3 = &uart3;
>> + serial4 = &uart4;
>> + serial5 = &uart5;
>> + ethernet0 = &gmac;
>> + };
>> +
>> + chosen {
>> + #address-cells = <1>;
>> + #size-cells = <1>;
>> + ranges;
>> +
>> + framebuffer at 0 {
>> + compatible = "allwinner,simple-framebuffer", "simple-framebuffer";
>> + allwinner,pipeline = "de_be0-lcd0-hdmi";
>> + clocks = <&pll6>;
>
> pll6 uses an argument now
>
>> + status = "disabled";
>> + };
>> + };
>> +
>> + cpus {
>> + enable-method = "allwinner,sun6i-a31";
>
> allwinner,sun6i-a31s I guess?
>
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> +
>> + cpu at 0 {
>> + compatible = "arm,cortex-a7";
>> + device_type = "cpu";
>> + reg = <0>;
>> + };
>> +
>> + cpu at 1 {
>> + compatible = "arm,cortex-a7";
>> + device_type = "cpu";
>> + reg = <1>;
>> + };
>> +
>> + cpu at 2 {
>> + compatible = "arm,cortex-a7";
>> + device_type = "cpu";
>> + reg = <2>;
>> + };
>> +
>> + cpu at 3 {
>> + compatible = "arm,cortex-a7";
>> + device_type = "cpu";
>> + reg = <3>;
>> + };
>> + };
>> +
>> + memory {
>> + reg = <0x40000000 0x80000000>;
>> + };
>> +
>> + pmu {
>> + compatible = "arm,cortex-a7-pmu", "arm,cortex-a15-pmu";
>> + interrupts = <0 120 4>,
>> + <0 121 4>,
>> + <0 122 4>,
>> + <0 123 4>;
>> + };
>> +
>> + clocks {
>> + #address-cells = <1>;
>> + #size-cells = <1>;
>> + ranges;
>> +
>> + osc24M: osc24M {
>> + #clock-cells = <0>;
>> + compatible = "fixed-clock";
>> + clock-frequency = <24000000>;
>> + };
>> +
>> + osc32k: clk at 0 {
>> + #clock-cells = <0>;
>> + compatible = "fixed-clock";
>> + clock-frequency = <32768>;
>> + clock-output-names = "osc32k";
>> + };
>> +
>> + pll1: clk at 01c20000 {
>> + #clock-cells = <0>;
>> + compatible = "allwinner,sun6i-a31-pll1-clk";
>> + reg = <0x01c20000 0x4>;
>> + clocks = <&osc24M>;
>> + clock-output-names = "pll1";
>> + };
>> +
>> + pll6: clk at 01c20028 {
>> + #clock-cells = <0>;
>> + compatible = "allwinner,sun6i-a31-pll6-clk";
>> + reg = <0x01c20028 0x4>;
>> + clocks = <&osc24M>;
>> + clock-output-names = "pll6";
>> + };
>> +
>> + cpu: cpu at 01c20050 {
>> + #clock-cells = <0>;
>> + compatible = "allwinner,sun4i-a10-cpu-clk";
>> + reg = <0x01c20050 0x4>;
>> +
>> + /*
>> + * PLL1 is listed twice here.
>> + * While it looks suspicious, it's actually documented
>> + * that way both in the datasheet and in the code from
>> + * Allwinner.
>> + */
>> + clocks = <&osc32k>, <&osc24M>, <&pll1>, <&pll1>;
>> + clock-output-names = "cpu";
>> + };
>> +
>> + axi: axi at 01c20050 {
>> + #clock-cells = <0>;
>> + compatible = "allwinner,sun4i-a10-axi-clk";
>> + reg = <0x01c20050 0x4>;
>> + clocks = <&cpu>;
>> + clock-output-names = "axi";
>> + };
>> +
>> + ahb1_mux: ahb1_mux at 01c20054 {
>> + #clock-cells = <0>;
>> + compatible = "allwinner,sun6i-a31-ahb1-mux-clk";
>> + reg = <0x01c20054 0x4>;
>> + clocks = <&osc32k>, <&osc24M>, <&axi>, <&pll6>;
>> + clock-output-names = "ahb1_mux";
>> + };
>> +
>> + ahb1: ahb1 at 01c20054 {
>> + #clock-cells = <0>;
>> + compatible = "allwinner,sun4i-a10-ahb-clk";
>> + reg = <0x01c20054 0x4>;
>> + clocks = <&ahb1_mux>;
>> + clock-output-names = "ahb1";
>> + };
>> +
>> + ahb1_gates: clk at 01c20060 {
>> + #clock-cells = <1>;
>> + compatible = "allwinner,sun6i-a31-ahb1-gates-clk";
>> + reg = <0x01c20060 0x8>;
>> + clocks = <&ahb1>;
>> + clock-output-names = "ahb1_mipidsi", "ahb1_ss",
>> + "ahb1_dma", "ahb1_mmc0", "ahb1_mmc1",
>> + "ahb1_mmc2", "ahb1_mmc3", "ahb1_nand1",
>> + "ahb1_nand0", "ahb1_sdram",
>> + "ahb1_gmac", "ahb1_ts", "ahb1_hstimer",
>> + "ahb1_spi0", "ahb1_spi1", "ahb1_spi2",
>> + "ahb1_spi3", "ahb1_otg", "ahb1_ehci0",
>> + "ahb1_ehci1", "ahb1_ohci0",
>> + "ahb1_ohci1", "ahb1_ohci2", "ahb1_ve",
>> + "ahb1_lcd0", "ahb1_lcd1", "ahb1_csi",
>> + "ahb1_hdmi", "ahb1_de0", "ahb1_de1",
>> + "ahb1_fe0", "ahb1_fe1", "ahb1_mp",
>> + "ahb1_gpu", "ahb1_deu0", "ahb1_deu1",
>> + "ahb1_drc0", "ahb1_drc1";
>> + };
>
> Are the gates really identical?
>
> As in not even stripped down?
According to the user manuals, the AHB1 gates on the A31s don't have
GMAC (or EMAC in the manual) and MIPI DSI listed. Though it seems
a lot of A31s hardware out there actually use GMAC.
The APB1 and APB2 gates are the same.
>> + apb1: apb1 at 01c20054 {
>> + #clock-cells = <0>;
>> + compatible = "allwinner,sun4i-a10-apb0-clk";
>> + reg = <0x01c20054 0x4>;
>> + clocks = <&ahb1>;
>> + clock-output-names = "apb1";
>> + };
>> +
>> + apb1_gates: clk at 01c20068 {
>> + #clock-cells = <1>;
>> + compatible = "allwinner,sun6i-a31-apb1-gates-clk";
>> + reg = <0x01c20068 0x4>;
>> + clocks = <&apb1>;
>> + clock-output-names = "apb1_codec", "apb1_digital_mic",
>> + "apb1_pio", "apb1_daudio0",
>> + "apb1_daudio1";
>> + };
>> +
>> + apb2_mux: apb2_mux at 01c20058 {
>> + #clock-cells = <0>;
>> + compatible = "allwinner,sun4i-a10-apb1-mux-clk";
>> + reg = <0x01c20058 0x4>;
>> + clocks = <&osc32k>, <&osc24M>, <&pll6>, <&pll6>;
>> + clock-output-names = "apb2_mux";
>> + };
>> +
>> + apb2: apb2 at 01c20058 {
>> + #clock-cells = <0>;
>> + compatible = "allwinner,sun6i-a31-apb2-div-clk";
>> + reg = <0x01c20058 0x4>;
>> + clocks = <&apb2_mux>;
>> + clock-output-names = "apb2";
>> + };
>> +
>> + apb2_gates: clk at 01c2006c {
>> + #clock-cells = <1>;
>> + compatible = "allwinner,sun6i-a31-apb2-gates-clk";
>> + reg = <0x01c2006c 0x4>;
>> + clocks = <&apb2>;
>> + clock-output-names = "apb2_i2c0", "apb2_i2c1",
>> + "apb2_i2c2", "apb2_i2c3", "apb2_uart0",
>> + "apb2_uart1", "apb2_uart2", "apb2_uart3",
>> + "apb2_uart4", "apb2_uart5";
>> + };
>> +
>> + mmc0_clk: clk at 01c20088 {
>> + #clock-cells = <0>;
>> + compatible = "allwinner,sun4i-a10-mod0-clk";
>> + reg = <0x01c20088 0x4>;
>> + clocks = <&osc24M>, <&pll6>;
>> + clock-output-names = "mmc0";
>> + };
>> +
>> + mmc1_clk: clk at 01c2008c {
>> + #clock-cells = <0>;
>> + compatible = "allwinner,sun4i-a10-mod0-clk";
>> + reg = <0x01c2008c 0x4>;
>> + clocks = <&osc24M>, <&pll6>;
>> + clock-output-names = "mmc1";
>> + };
>> +
>> + mmc2_clk: clk at 01c20090 {
>> + #clock-cells = <0>;
>> + compatible = "allwinner,sun4i-a10-mod0-clk";
>> + reg = <0x01c20090 0x4>;
>> + clocks = <&osc24M>, <&pll6>;
>> + clock-output-names = "mmc2";
>> + };
>> +
>> + mmc3_clk: clk at 01c20094 {
>> + #clock-cells = <0>;
>> + compatible = "allwinner,sun4i-a10-mod0-clk";
>> + reg = <0x01c20094 0x4>;
>> + clocks = <&osc24M>, <&pll6>;
>> + clock-output-names = "mmc3";
>> + };
>> +
>> + spi0_clk: clk at 01c200a0 {
>> + #clock-cells = <0>;
>> + compatible = "allwinner,sun4i-a10-mod0-clk";
>> + reg = <0x01c200a0 0x4>;
>> + clocks = <&osc24M>, <&pll6>;
>> + clock-output-names = "spi0";
>> + };
>> +
>> + spi1_clk: clk at 01c200a4 {
>> + #clock-cells = <0>;
>> + compatible = "allwinner,sun4i-a10-mod0-clk";
>> + reg = <0x01c200a4 0x4>;
>> + clocks = <&osc24M>, <&pll6>;
>> + clock-output-names = "spi1";
>> + };
>> +
>> + spi2_clk: clk at 01c200a8 {
>> + #clock-cells = <0>;
>> + compatible = "allwinner,sun4i-a10-mod0-clk";
>> + reg = <0x01c200a8 0x4>;
>> + clocks = <&osc24M>, <&pll6>;
>> + clock-output-names = "spi2";
>> + };
>> +
>> + spi3_clk: clk at 01c200ac {
>> + #clock-cells = <0>;
>> + compatible = "allwinner,sun4i-a10-mod0-clk";
>> + reg = <0x01c200ac 0x4>;
>> + clocks = <&osc24M>, <&pll6>;
>> + clock-output-names = "spi3";
>> + };
>> +
>> + usb_clk: clk at 01c200cc {
>> + #clock-cells = <1>;
>> + #reset-cells = <1>;
>> + compatible = "allwinner,sun6i-a31-usb-clk";
>> + reg = <0x01c200cc 0x4>;
>> + clocks = <&osc24M>;
>> + clock-output-names = "usb_phy0", "usb_phy1", "usb_phy2",
>> + "usb_ohci0", "usb_ohci1",
>> + "usb_ohci2";
>> + };
>> +
>> + /*
>> + * The following two are dummy clocks, placeholders used in the gmac_tx
>> + * clock. The gmac driver will choose one parent depending on the PHY
>> + * interface mode, using clk_set_rate auto-reparenting.
>> + * The actual TX clock rate is not controlled by the gmac_tx clock.
>> + */
>> + mii_phy_tx_clk: clk at 1 {
>> + #clock-cells = <0>;
>> + compatible = "fixed-clock";
>> + clock-frequency = <25000000>;
>> + clock-output-names = "mii_phy_tx";
>> + };
>> +
>> + gmac_int_tx_clk: clk at 2 {
>> + #clock-cells = <0>;
>> + compatible = "fixed-clock";
>> + clock-frequency = <125000000>;
>> + clock-output-names = "gmac_int_tx";
>> + };
>> +
>> + gmac_tx_clk: clk at 01c200d0 {
>> + #clock-cells = <0>;
>> + compatible = "allwinner,sun7i-a20-gmac-clk";
>> + reg = <0x01c200d0 0x4>;
>> + clocks = <&mii_phy_tx_clk>, <&gmac_int_tx_clk>;
>> + clock-output-names = "gmac_tx";
>> + };
>> + };
>> +
>> + soc at 01c00000 {
>> + compatible = "simple-bus";
>> + #address-cells = <1>;
>> + #size-cells = <1>;
>> + ranges;
>> +
>> + dma: dma-controller at 01c02000 {
>> + compatible = "allwinner,sun6i-a31-dma";
>> + reg = <0x01c02000 0x1000>;
>> + interrupts = <0 50 4>;
>> + clocks = <&ahb1_gates 6>;
>> + resets = <&ahb1_rst 6>;
>> + #dma-cells = <1>;
>> + };
>> +
>> + mmc0: mmc at 01c0f000 {
>> + compatible = "allwinner,sun5i-a13-mmc";
>> + reg = <0x01c0f000 0x1000>;
>> + clocks = <&ahb1_gates 8>, <&mmc0_clk>;
>> + clock-names = "ahb", "mmc";
>> + resets = <&ahb1_rst 8>;
>> + reset-names = "ahb";
>> + interrupts = <0 60 4>;
>> + status = "disabled";
>> + };
>> +
>> + mmc1: mmc at 01c10000 {
>> + compatible = "allwinner,sun5i-a13-mmc";
>> + reg = <0x01c10000 0x1000>;
>> + clocks = <&ahb1_gates 9>, <&mmc1_clk>;
>> + clock-names = "ahb", "mmc";
>> + resets = <&ahb1_rst 9>;
>> + reset-names = "ahb";
>> + interrupts = <0 61 4>;
>> + status = "disabled";
>> + };
>> +
>> + mmc2: mmc at 01c11000 {
>> + compatible = "allwinner,sun5i-a13-mmc";
>> + reg = <0x01c11000 0x1000>;
>> + clocks = <&ahb1_gates 10>, <&mmc2_clk>;
>> + clock-names = "ahb", "mmc";
>> + resets = <&ahb1_rst 10>;
>> + reset-names = "ahb";
>> + interrupts = <0 62 4>;
>> + status = "disabled";
>> + };
>> +
>> + mmc3: mmc at 01c12000 {
>> + compatible = "allwinner,sun5i-a13-mmc";
>> + reg = <0x01c12000 0x1000>;
>> + clocks = <&ahb1_gates 11>, <&mmc3_clk>;
>> + clock-names = "ahb", "mmc";
>> + resets = <&ahb1_rst 11>;
>> + reset-names = "ahb";
>> + interrupts = <0 63 4>;
>> + status = "disabled";
>> + };
>> +
>> + usbphy: phy at 01c19400 {
>> + compatible = "allwinner,sun6i-a31-usb-phy";
>> + reg = <0x01c19400 0x10>,
>> + <0x01c1a800 0x4>,
>> + <0x01c1b800 0x4>;
>> + reg-names = "phy_ctrl",
>> + "pmu1",
>> + "pmu2";
>> + clocks = <&usb_clk 8>,
>> + <&usb_clk 9>,
>> + <&usb_clk 10>;
>> + clock-names = "usb0_phy",
>> + "usb1_phy",
>> + "usb2_phy";
>> + resets = <&usb_clk 0>,
>> + <&usb_clk 1>,
>> + <&usb_clk 2>;
>> + reset-names = "usb0_reset",
>> + "usb1_reset",
>> + "usb2_reset";
>> + status = "disabled";
>> + #phy-cells = <1>;
>> + };
>> +
>> + ehci0: usb at 01c1a000 {
>> + compatible = "allwinner,sun6i-a31-ehci", "generic-ehci";
>> + reg = <0x01c1a000 0x100>;
>> + interrupts = <0 72 4>;
>> + clocks = <&ahb1_gates 26>;
>> + resets = <&ahb1_rst 26>;
>> + phys = <&usbphy 1>;
>> + phy-names = "usb";
>> + status = "disabled";
>> + };
>> +
>> + ohci0: usb at 01c1a400 {
>> + compatible = "allwinner,sun6i-a31-ohci", "generic-ohci";
>> + reg = <0x01c1a400 0x100>;
>> + interrupts = <0 73 4>;
>> + clocks = <&ahb1_gates 29>, <&usb_clk 16>;
>> + resets = <&ahb1_rst 29>;
>> + phys = <&usbphy 1>;
>> + phy-names = "usb";
>> + status = "disabled";
>> + };
>> +
>> + ehci1: usb at 01c1b000 {
>> + compatible = "allwinner,sun6i-a31-ehci", "generic-ehci";
>> + reg = <0x01c1b000 0x100>;
>> + interrupts = <0 74 4>;
>> + clocks = <&ahb1_gates 27>;
>> + resets = <&ahb1_rst 27>;
>> + phys = <&usbphy 2>;
>> + phy-names = "usb";
>> + status = "disabled";
>> + };
>> +
>> + ohci1: usb at 01c1b400 {
>> + compatible = "allwinner,sun6i-a31-ohci", "generic-ohci";
>> + reg = <0x01c1b400 0x100>;
>> + interrupts = <0 75 4>;
>> + clocks = <&ahb1_gates 30>, <&usb_clk 17>;
>> + resets = <&ahb1_rst 30>;
>> + phys = <&usbphy 2>;
>> + phy-names = "usb";
>> + status = "disabled";
>> + };
>> +
>> + pio: pinctrl at 01c20800 {
>> + compatible = "allwinner,sun6i-a31s-pinctrl";
>> + reg = <0x01c20800 0x400>;
>> + interrupts = <0 11 4>,
>> + <0 15 4>,
>> + <0 16 4>,
>> + <0 17 4>;
>> + clocks = <&apb1_gates 5>;
>> + gpio-controller;
>> + interrupt-controller;
>> + #interrupt-cells = <2>;
>> + #size-cells = <0>;
>> + #gpio-cells = <3>;
>> +
>> + uart0_pins_a: uart0 at 0 {
>> + allwinner,pins = "PH20", "PH21";
>> + allwinner,function = "uart0";
>> + allwinner,drive = <0>;
>> + allwinner,pull = <0>;
>> + };
>> +
>> + i2c0_pins_a: i2c0 at 0 {
>> + allwinner,pins = "PH14", "PH15";
>> + allwinner,function = "i2c0";
>> + allwinner,drive = <0>;
>> + allwinner,pull = <0>;
>> + };
>> +
>> + i2c1_pins_a: i2c1 at 0 {
>> + allwinner,pins = "PH16", "PH17";
>> + allwinner,function = "i2c1";
>> + allwinner,drive = <0>;
>> + allwinner,pull = <0>;
>> + };
>> +
>> + i2c2_pins_a: i2c2 at 0 {
>> + allwinner,pins = "PH18", "PH19";
>> + allwinner,function = "i2c2";
>> + allwinner,drive = <0>;
>> + allwinner,pull = <0>;
>> + };
>> +
>> + mmc0_pins_a: mmc0 at 0 {
>> + allwinner,pins = "PF0","PF1","PF2","PF3","PF4","PF5";
>
> Spaces after the comma, and I guess that would be better on two lines.
This is in the other dtsi. We should probably fix the styling there as well.
>> + allwinner,function = "mmc0";
>> + allwinner,drive = <2>;
>> + allwinner,pull = <0>;
>> + };
>> +
>> + gmac_pins_mii_a: gmac_mii at 0 {
>> + allwinner,pins = "PA0", "PA1", "PA2", "PA3",
>> + "PA8", "PA9", "PA11",
>> + "PA12", "PA13", "PA14", "PA19",
>> + "PA20", "PA21", "PA22", "PA23",
>> + "PA24", "PA26", "PA27";
>> + allwinner,function = "gmac";
>> + allwinner,drive = <0>;
>> + allwinner,pull = <0>;
>> + };
>> +
>> + gmac_pins_gmii_a: gmac_gmii at 0 {
>> + allwinner,pins = "PA0", "PA1", "PA2", "PA3",
>> + "PA4", "PA5", "PA6", "PA7",
>> + "PA8", "PA9", "PA10", "PA11",
>> + "PA12", "PA13", "PA14", "PA15",
>> + "PA16", "PA17", "PA18", "PA19",
>> + "PA20", "PA21", "PA22", "PA23",
>> + "PA24", "PA25", "PA26", "PA27";
>> + allwinner,function = "gmac";
>> + /*
>> + * data lines in GMII mode run at 125MHz and
>> + * might need a higher signal drive strength
>> + */
>> + allwinner,drive = <2>;
>> + allwinner,pull = <0>;
>> + };
>> +
>> + gmac_pins_rgmii_a: gmac_rgmii at 0 {
>> + allwinner,pins = "PA0", "PA1", "PA2", "PA3",
>> + "PA9", "PA10", "PA11",
>> + "PA12", "PA13", "PA14", "PA19",
>> + "PA20", "PA25", "PA26", "PA27";
>> + allwinner,function = "gmac";
>> + /*
>> + * data lines in RGMII mode use DDR mode
>> + * and need a higher signal drive strength
>> + */
>> + allwinner,drive = <3>;
>> + allwinner,pull = <0>;
>> + };
>> + };
>> +
>> + ahb1_rst: reset at 01c202c0 {
>> + #reset-cells = <1>;
>> + compatible = "allwinner,sun6i-a31-ahb1-reset";
>> + reg = <0x01c202c0 0xc>;
>> + };
>> +
>> + apb1_rst: reset at 01c202d0 {
>> + #reset-cells = <1>;
>> + compatible = "allwinner,sun6i-a31-clock-reset";
>> + reg = <0x01c202d0 0x4>;
>> + };
>> +
>> + apb2_rst: reset at 01c202d8 {
>> + #reset-cells = <1>;
>> + compatible = "allwinner,sun6i-a31-clock-reset";
>> + reg = <0x01c202d8 0x4>;
>> + };
>> +
>> + timer at 01c20c00 {
>> + compatible = "allwinner,sun4i-a10-timer";
>> + reg = <0x01c20c00 0xa0>;
>> + interrupts = <0 18 4>,
>> + <0 19 4>,
>> + <0 20 4>,
>> + <0 21 4>,
>> + <0 22 4>;
>> + clocks = <&osc24M>;
>> + };
>> +
>> + wdt1: watchdog at 01c20ca0 {
>> + compatible = "allwinner,sun6i-a31-wdt";
>> + reg = <0x01c20ca0 0x20>;
>> + };
>> +
>> + uart0: serial at 01c28000 {
>> + compatible = "snps,dw-apb-uart";
>> + reg = <0x01c28000 0x400>;
>> + interrupts = <0 0 4>;
>> + reg-shift = <2>;
>> + reg-io-width = <4>;
>> + clocks = <&apb2_gates 16>;
>> + resets = <&apb2_rst 16>;
>> + dmas = <&dma 6>, <&dma 6>;
>> + dma-names = "rx", "tx";
>> + status = "disabled";
>> + };
>> +
>> + uart1: serial at 01c28400 {
>> + compatible = "snps,dw-apb-uart";
>> + reg = <0x01c28400 0x400>;
>> + interrupts = <0 1 4>;
>> + reg-shift = <2>;
>> + reg-io-width = <4>;
>> + clocks = <&apb2_gates 17>;
>> + resets = <&apb2_rst 17>;
>> + dmas = <&dma 7>, <&dma 7>;
>> + dma-names = "rx", "tx";
>> + status = "disabled";
>> + };
>> +
>> + uart2: serial at 01c28800 {
>> + compatible = "snps,dw-apb-uart";
>> + reg = <0x01c28800 0x400>;
>> + interrupts = <0 2 4>;
>> + reg-shift = <2>;
>> + reg-io-width = <4>;
>> + clocks = <&apb2_gates 18>;
>> + resets = <&apb2_rst 18>;
>> + dmas = <&dma 8>, <&dma 8>;
>> + dma-names = "rx", "tx";
>> + status = "disabled";
>> + };
>> +
>> + uart3: serial at 01c28c00 {
>> + compatible = "snps,dw-apb-uart";
>> + reg = <0x01c28c00 0x400>;
>> + interrupts = <0 3 4>;
>> + reg-shift = <2>;
>> + reg-io-width = <4>;
>> + clocks = <&apb2_gates 19>;
>> + resets = <&apb2_rst 19>;
>> + dmas = <&dma 9>, <&dma 9>;
>> + dma-names = "rx", "tx";
>> + status = "disabled";
>> + };
>> +
>> + uart4: serial at 01c29000 {
>> + compatible = "snps,dw-apb-uart";
>> + reg = <0x01c29000 0x400>;
>> + interrupts = <0 4 4>;
>> + reg-shift = <2>;
>> + reg-io-width = <4>;
>> + clocks = <&apb2_gates 20>;
>> + resets = <&apb2_rst 20>;
>> + dmas = <&dma 10>, <&dma 10>;
>> + dma-names = "rx", "tx";
>> + status = "disabled";
>> + };
>> +
>> + uart5: serial at 01c29400 {
>> + compatible = "snps,dw-apb-uart";
>> + reg = <0x01c29400 0x400>;
>> + interrupts = <0 5 4>;
>> + reg-shift = <2>;
>> + reg-io-width = <4>;
>> + clocks = <&apb2_gates 21>;
>> + resets = <&apb2_rst 21>;
>> + dmas = <&dma 22>, <&dma 22>;
>> + dma-names = "rx", "tx";
>> + status = "disabled";
>> + };
>> +
>> + i2c0: i2c at 01c2ac00 {
>> + compatible = "allwinner,sun6i-a31-i2c";
>> + reg = <0x01c2ac00 0x400>;
>> + interrupts = <0 6 4>;
>> + clocks = <&apb2_gates 0>;
>> + resets = <&apb2_rst 0>;
>> + status = "disabled";
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> + };
>> +
>> + i2c1: i2c at 01c2b000 {
>> + compatible = "allwinner,sun6i-a31-i2c";
>> + reg = <0x01c2b000 0x400>;
>> + interrupts = <0 7 4>;
>> + clocks = <&apb2_gates 1>;
>> + resets = <&apb2_rst 1>;
>> + status = "disabled";
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> + };
>> +
>> + i2c2: i2c at 01c2b400 {
>> + compatible = "allwinner,sun6i-a31-i2c";
>> + reg = <0x01c2b400 0x400>;
>> + interrupts = <0 8 4>;
>> + clocks = <&apb2_gates 2>;
>> + resets = <&apb2_rst 2>;
>> + status = "disabled";
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> + };
>> +
>> + i2c3: i2c at 01c2b800 {
>> + compatible = "allwinner,sun6i-a31-i2c";
>> + reg = <0x01c2b800 0x400>;
>> + interrupts = <0 9 4>;
>> + clocks = <&apb2_gates 3>;
>> + resets = <&apb2_rst 3>;
>> + status = "disabled";
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> + };
>> +
>> + gmac: ethernet at 01c30000 {
>> + compatible = "allwinner,sun7i-a20-gmac";
>> + reg = <0x01c30000 0x1054>;
>> + interrupts = <0 82 4>;
>> + interrupt-names = "macirq";
>> + clocks = <&ahb1_gates 17>, <&gmac_tx_clk>;
>> + clock-names = "stmmaceth", "allwinner_gmac_tx";
>> + resets = <&ahb1_rst 17>;
>> + reset-names = "stmmaceth";
>> + snps,pbl = <2>;
>> + snps,fixed-burst;
>> + snps,force_sf_dma_mode;
>> + status = "disabled";
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> + };
>> +
>> + timer at 01c60000 {
>> + compatible = "allwinner,sun6i-a31-hstimer", "allwinner,sun7i-a20-hstimer";
>> + reg = <0x01c60000 0x1000>;
>> + interrupts = <0 51 4>,
>> + <0 52 4>,
>> + <0 53 4>,
>> + <0 54 4>;
>> + clocks = <&ahb1_gates 19>;
>> + resets = <&ahb1_rst 19>;
>> + };
>> +
>> + spi0: spi at 01c68000 {
>> + compatible = "allwinner,sun6i-a31-spi";
>> + reg = <0x01c68000 0x1000>;
>> + interrupts = <0 65 4>;
>> + clocks = <&ahb1_gates 20>, <&spi0_clk>;
>> + clock-names = "ahb", "mod";
>> + dmas = <&dma 23>, <&dma 23>;
>> + dma-names = "rx", "tx";
>> + resets = <&ahb1_rst 20>;
>> + status = "disabled";
>> + };
>> +
>> + spi1: spi at 01c69000 {
>> + compatible = "allwinner,sun6i-a31-spi";
>> + reg = <0x01c69000 0x1000>;
>> + interrupts = <0 66 4>;
>> + clocks = <&ahb1_gates 21>, <&spi1_clk>;
>> + clock-names = "ahb", "mod";
>> + dmas = <&dma 24>, <&dma 24>;
>> + dma-names = "rx", "tx";
>> + resets = <&ahb1_rst 21>;
>> + status = "disabled";
>> + };
>> +
>> + spi2: spi at 01c6a000 {
>> + compatible = "allwinner,sun6i-a31-spi";
>> + reg = <0x01c6a000 0x1000>;
>> + interrupts = <0 67 4>;
>> + clocks = <&ahb1_gates 22>, <&spi2_clk>;
>> + clock-names = "ahb", "mod";
>> + dmas = <&dma 25>, <&dma 25>;
>> + dma-names = "rx", "tx";
>> + resets = <&ahb1_rst 22>;
>> + status = "disabled";
>> + };
>> +
>> + spi3: spi at 01c6b000 {
>> + compatible = "allwinner,sun6i-a31-spi";
>> + reg = <0x01c6b000 0x1000>;
>> + interrupts = <0 68 4>;
>> + clocks = <&ahb1_gates 23>, <&spi3_clk>;
>> + clock-names = "ahb", "mod";
>> + dmas = <&dma 26>, <&dma 26>;
>> + dma-names = "rx", "tx";
>> + resets = <&ahb1_rst 23>;
>> + status = "disabled";
>> + };
>> +
>> + gic: interrupt-controller at 01c81000 {
>> + compatible = "arm,cortex-a7-gic", "arm,cortex-a15-gic";
>> + reg = <0x01c81000 0x1000>,
>> + <0x01c82000 0x1000>,
>> + <0x01c84000 0x2000>,
>> + <0x01c86000 0x2000>;
>> + interrupt-controller;
>> + #interrupt-cells = <3>;
>> + interrupts = <1 9 0xf04>;
>> + };
>> +
>> + rtc: rtc at 01f00000 {
>> + compatible = "allwinner,sun6i-a31-rtc";
>> + reg = <0x01f00000 0x54>;
>> + interrupts = <0 40 4>, <0 41 4>;
>> + };
>> +
>> + nmi_intc: interrupt-controller at 01f00c0c {
>> + compatible = "allwinner,sun6i-a31-sc-nmi";
>> + interrupt-controller;
>> + #interrupt-cells = <2>;
>> + reg = <0x01f00c0c 0x38>;
>> + interrupts = <0 32 4>;
>> + };
>> +
>> + prcm at 01f01400 {
>> + compatible = "allwinner,sun6i-a31-prcm";
>> + reg = <0x01f01400 0x200>;
>> +
>> + ar100: ar100_clk {
>> + compatible = "allwinner,sun6i-a31-ar100-clk";
>> + #clock-cells = <0>;
>> + clocks = <&osc32k>, <&osc24M>, <&pll6>, <&pll6>;
>> + clock-output-names = "ar100";
>> + };
>> +
>> + ahb0: ahb0_clk {
>> + compatible = "fixed-factor-clock";
>> + #clock-cells = <0>;
>> + clock-div = <1>;
>> + clock-mult = <1>;
>> + clocks = <&ar100>;
>> + clock-output-names = "ahb0";
>> + };
>> +
>> + apb0: apb0_clk {
>> + compatible = "allwinner,sun6i-a31-apb0-clk";
>> + #clock-cells = <0>;
>> + clocks = <&ahb0>;
>> + clock-output-names = "apb0";
>> + };
>> +
>> + apb0_gates: apb0_gates_clk {
>> + compatible = "allwinner,sun6i-a31-apb0-gates-clk";
>> + #clock-cells = <1>;
>> + clocks = <&apb0>;
>> + clock-output-names = "apb0_pio", "apb0_ir",
>> + "apb0_timer", "apb0_p2wi",
>> + "apb0_uart", "apb0_1wire",
>> + "apb0_i2c";
>> + };
>> +
>> + ir_clk: ir_clk {
>> + #clock-cells = <0>;
>> + compatible = "allwinner,sun6i-a31-ir-clk";
>> + clocks = <&osc32k>, <&osc24M>;
>> + clock-output-names = "ir";
>> + };
>
> This is yet to be agreed on....
>
>> +
>> + apb0_rst: apb0_rst {
>> + compatible = "allwinner,sun6i-a31-clock-reset";
>> + #reset-cells = <1>;
>> + };
>> + };
>> +
>> + cpucfg at 01f01c00 {
>> + compatible = "allwinner,sun6i-a31-cpuconfig";
>> + reg = <0x01f01c00 0x300>;
>> + };
>> +
>> + ir at 01f02000 {
>> + compatible = "allwinner,sun5i-a13-ir";
>> + clocks = <&apb0_gates 1>, <&ir_clk>;
>> + clock-names = "apb", "ir";
>> + resets = <&apb0_rst 1>;
>> + interrupts = <0 37 4>;
>> + reg = <0x01f02000 0x40>;
>> + status = "disabled";
>> + };
>> +
>> + r_pio: pinctrl at 01f02c00 {
>> + compatible = "allwinner,sun6i-a31-r-pinctrl";
>> + reg = <0x01f02c00 0x400>;
>> + interrupts = <0 45 4>,
>> + <0 46 4>;
>> + clocks = <&apb0_gates 0>;
>> + resets = <&apb0_rst 0>;
>> + gpio-controller;
>> + interrupt-controller;
>> + #interrupt-cells = <2>;
>> + #size-cells = <0>;
>> + #gpio-cells = <3>;
>> +
>> + ir_pins_a: ir at 0 {
>> + allwinner,pins = "PL4";
>> + allwinner,function = "s_ir";
>> + allwinner,drive = <0>;
>> + allwinner,pull = <0>;
>> + };
>> + };
>> + };
>> +};
>> --
>> 2.1.0
>>
More information about the linux-arm-kernel
mailing list