[PATCH] mmc: dw_mmc: add quirk for data over interrupt timeout
Addy
addy.ke at rock-chips.com
Mon Nov 24 22:30:49 PST 2014
Hi, Jaehoon
On 2014/11/20 18:01, Jaehoon Chung wrote:
> Hi, Addy.
>
> On 11/20/2014 06:33 PM, addy ke wrote:
>> Hi, Jaehoon
>>
>> On 2014/11/19 13:56, addy ke wrote:
>>> Hi Jaehoon
>>>
>>> On 2014/11/19 09:22, Jaehoon Chung Wrote:
>>>> Hi, Addy.
>>>>
>>>> On 11/18/2014 09:32 AM, Addy wrote:
>>>>> On 2014年11月14日 21:18, Jaehoon Chung wrote:
>>>>>> Hi, Addy.
>>>>>>
>>>>>> Did you use the DW_MCI_QUIRK_IDMAC_DTO?
>>>>>> I'm not sure, but i wonder if you get what result when you use above quirk.
>>>>> DW_MCI_QUIRK_IDMAC_DTO is only for version2.0 or below.
>>>>> /*
>>>>> * DTO fix - version 2.10a and below, and only if internal DMA
>>>>> * is configured.
>>>>> */
>>>>> if (host->quirks & DW_MCI_QUIRK_IDMAC_DTO) {
>>>>> if (!pending &&
>>>>> ((mci_readl(host, STATUS) >> 17) & 0x1fff))
>>>>> pending |= SDMMC_INT_DATA_OVER;
>>>>> }
>>>>>
>>>>> It meams that if interrupt comes, but pending = 0 && FIFO_COUNT(bit17-29) !=0,
>>>>> then force to set SDMMC_INT_DATA_OVER.
>>>>> But in our case, FIFO_COUNT = 0 (STATUS register value is 0xad06). This is
>>>>> because that the card does not send data to host. So there is no interrupts come,
>>>>> and interrupt handle function(dw_mci_interrupt) will not be called. So we need a
>>>>> timer to handle this case.
>>>>>
>>>>> So I think SDMMC_INT_DATA_OVER is not suitable for this case, and we need a new
>>>>> quirk.
>>>>>
>>>>>> And i will check more this patch at next week.
>>>>>>
>>>>>> Thanks for your efforts.
>>>>>>
>>>>>> Best Regards,
>>>>>> Jaehoon Chung
>>>>>>
>>>>>> On 11/14/2014 10:05 PM, Addy Ke wrote:
>>>>>>> From: Addy <addy.ke at rock-chips.com>
>>>>>>>
>>>>>>> This patch add a new quirk to notify the driver to teminate
>>>>>>> current transfer and report a data timeout to the core,
>>>>>>> if data over interrupt does NOT come within the given time.
>>>>>>>
>>>>>>> dw_mmc call mmc_request_done func to finish transfer depends on
>>>>>>> data over interrupt. If data over interrupt does not come in
>>>>>>> sending data state, the current transfer will be blocked.
>>>>>>>
>>>>>>> But this case really exists, when driver reads tuning data from
>>>>>>> card on rk3288-pink2 board. I measured waveforms by oscilloscope
>>>>>>> and found that card clock was always on and data lines were always
>>>>>>> holded high level in sending data state. This is the cause that
>>>>>>> card does NOT send data to host.
>>>>>>>
>>>>>>> According to synopsys designware databook, the timeout counter is
>>>>>>> started only after the card clock is stopped.
>>>>>>>
>>>>>>> So if card clock is always on, data read timeout interrupt will NOT come,
>>>>>>> and if data lines are always holded high level, all data-related
>>>>>>> interrupt such as start-bit error, data crc error, data over interrupt,
>>>>>>> end-bit error, and so on, will NOT come too.
>>>>>>>
>>>>>>> So driver can't get the current state, it can do nothing but wait for.
>>>>>>>
>>>>>>> This patch is based on https://patchwork.kernel.org/patch/5227941/
>>>>>>>
>>>>>>> Signed-off-by: Addy <addy.ke at rock-chips.com>
>>>>>>> ---
>>>>>>> drivers/mmc/host/dw_mmc.c | 47 +++++++++++++++++++++++++++++++++++++++++++++-
>>>>>>> include/linux/mmc/dw_mmc.h | 5 +++++
>>>>>>> 2 files changed, 51 insertions(+), 1 deletion(-)
>>>>>>>
>>>>>>> diff --git a/drivers/mmc/host/dw_mmc.c b/drivers/mmc/host/dw_mmc.c
>>>>>>> index b4c3044..3960fc3 100644
>>>>>>> --- a/drivers/mmc/host/dw_mmc.c
>>>>>>> +++ b/drivers/mmc/host/dw_mmc.c
>>>>>>> @@ -1448,6 +1448,17 @@ static int dw_mci_data_complete(struct dw_mci *host, struct mmc_data *data)
>>>>>>> return data->error;
>>>>>>> }
>>>>>>> +static inline void dw_mci_dto_start_monitor(struct dw_mci *host)
>>>>>>> +{
>>>>>>> + unsigned int data_tmout_clks;
>>>>>>> + unsigned int data_tmout_ms;
>>>>>>> +
>>>>>>> + data_tmout_clks = (mci_readl(host, TMOUT) >> 8);
>>>>>>> + data_tmout_ms = (data_tmout_clks * 1000 / host->bus_hz) + 250;
>>>> What's 250? And how about using the DIV_ROUND_UP?
>>>>
>>> 250ms is only for more timeout.
>>> maybe data timeout read from TMOUT register is enough.
>>> So, I will remove 250.
>>> new code:
>>> data_tmout_clks = (mci_readl(host, TMOUT) >> 8);
>>> data_tmout_ms = DIV_ROUND_UP(data_tmout_clks * 100, host->bus_hz);
>>> Is right?
>>>
>>>>>>> +
>>>>>>> + mod_timer(&host->dto_timer, jiffies + msecs_to_jiffies(data_tmout_ms));
>>>>>>> +}
>>>>>>> +
>>>>>>> static void dw_mci_tasklet_func(unsigned long priv)
>>>>>>> {
>>>>>>> struct dw_mci *host = (struct dw_mci *)priv;
>>>>>>> @@ -1522,8 +1533,11 @@ static void dw_mci_tasklet_func(unsigned long priv)
>>>>>>> }
>>>>>>> if (!test_and_clear_bit(EVENT_XFER_COMPLETE,
>>>>>>> - &host->pending_events))
>>>>>>> + &host->pending_events)) {
>>>>>>> + if (host->quirks & DW_MCI_QUIRK_DTO_TIMER)
>>>>>>> + dw_mci_dto_start_monitor(host);
>>>> if timer is starting at only here, dw_mci_dto_start_monitor() doesn't need.
>>>>
>>> Ok, I will change it in the next patch.
>>>>>>> break;
>>>>>>> + }
>>>>>>> set_bit(EVENT_XFER_COMPLETE, &host->completed_events);
>>>>>>> @@ -2115,6 +2129,9 @@ static irqreturn_t dw_mci_interrupt(int irq, void *dev_id)
>>>>>>> }
>>>>>>> if (pending & SDMMC_INT_DATA_OVER) {
>>>>>>> + if (host->quirks & DW_MCI_QUIRK_DTO_TIMER)
>>>>>>> + del_timer(&host->dto_timer);
>>>>>>> +
>>>>>>> mci_writel(host, RINTSTS, SDMMC_INT_DATA_OVER);
>>>>>>> if (!host->data_status)
>>>>>>> host->data_status = pending;
>>>>>>> @@ -2502,6 +2519,28 @@ ciu_out:
>>>>>>> return ret;
>>>>>>> }
>>>>>>> +static void dw_mci_dto_timer(unsigned long arg)
>>>>>>> +{
>>>>>>> + struct dw_mci *host = (struct dw_mci *)arg;
>>>> I prefer to use the "data" instead of "arg"
>>>>
>>> Ok, I will change it in the next patch.
>>>>>>> +
>>>>>>> + switch (host->state) {
>>>>>>> + case STATE_SENDING_DATA:
>>>>>>> + case STATE_DATA_BUSY:
>>>>>>> + /*
>>>>>>> + * If data over interrupt does NOT come in sending data state,
>>>>>>> + * we should notify the driver to teminate current transfer
>>>> teminate/terminate?
>>>>
>>> Am, I will change it in the next patch.
>>>>>>> + * and report a data timeout to the core.
>>>>>>> + */
>>>>>>> + host->data_status = SDMMC_INT_DRTO;
>>>>>>> + set_bit(EVENT_DATA_ERROR, &host->pending_events);
>>>>>>> + set_bit(EVENT_DATA_COMPLETE, &host->pending_events);
>>>> Dose it need to set EVENT_DATA_COMPLETE?
>>>>
>>> Yes, it is nessarry!
>>> If not, dw_mci_data_complete function will not be called in my test.
>>> Analysis as follows:
>>> After host recevied command response, driver call tasklet_schedule to
>>> set EVENT_CMD_COMPLETE, change state to STATE_SENDING_DATA, and call
>>> mod_timer. Because there is no any interrupts come in this case,
>>> tasklet_schedule function will not be called until dw_mci_timer is called.
>>>
>>> dw_mci_timer-->
>>> tasklet_schedule-->
>>> dw_mci_tasklet_func-->
>>> state == STATE_SENDING_DATA and EVENT_DATA_ERROR-->
>>> dw_mci_stop_dma, set EVENT_XFER_COMPLETE, send_stop_abort, state = STATE_DATA_ERROR, and then break;-->
>>> check state again -->
>>> state == STATE_DATA_ERROR, if it NOT set EVENT_DATA_COMPLETE in dw_mci_timer goto 1), else goto 2) -->
>>>
>>>
>>> 1) in case STATE_DATA_BUSY, there does nothing but break, and dw_mci_data_complete and dw_mci_request_end
>>> will not be called. then mmc blocks.
>>>
>>> 2) in case STATE_DATA_BUSY, becase EVENT_DATA_COMPLETE is set, dw_mci_data_complete and dw_mci_request_end
>>> will be called to report error to the core.
>>>
>>>
>>>
>>>>>>> + tasklet_schedule(&host->tasklet);
>>>>>>> + break;
>>>>>>> + default:
>>>>>>> + break;
>>>>>>> + }
>>>>>>> +}
>>>>>>> +
>>>>>>> #ifdef CONFIG_OF
>>>>>>> static struct dw_mci_of_quirks {
>>>>>>> char *quirk;
>>>>>>> @@ -2513,6 +2552,9 @@ static struct dw_mci_of_quirks {
>>>>>>> }, {
>>>>>>> .quirk = "disable-wp",
>>>>>>> .id = DW_MCI_QUIRK_NO_WRITE_PROTECT,
>>>>>>> + }, {
>>>>>>> + .quirk = "dto-timer",
>>>>>>> + .id = DW_MCI_QUIRK_DTO_TIMER,
>>>>>>> },
>>>> Well, this is s/w timer, so i'm not sure this can be merged into dt-file.
>>>> If this is generic solution, we can add s/w timer by default. how about?
>>> ok, I will change it in the next patch.
>>>
>> We got the reply from synopsys today:
>> There are two counters but both use the same value of [31:8] bits.
>> Data timeout counter doesn’t wait for stop clock and you should get DRTO even when the clock is not stopped.
>> Host Starvation timeout counter is triggered with stop clock condition.
> Then it doesn't need to add s/w timer. if it's working well, it should get DRTO, right?
> And Did you try to disable "low-power control"?
Sure, I think
It should get DRTO and DTO according to spec.
I have tried to disable "low-power control" , but dto still didn't come.
>> It seems that if card does not send data to host, DRTO interrupt will come.
>> But I really have NOT gotten DRTO interrupt and DTO interrupt in RK3X soc.
>> Is there other SOC which have the same problem?
> Did you get this problem at Only RK3X soc?
> Actually, i didn't have see similar problem before.
> If you have the error log, could you share it?
Yes, I only got this problem on rk3x.
And there is not any error log, after host receives command response and
enter "sending data state".
>> If not, I think we need a quirk for it.
> if you need to add this quirks, how about using "broken-dto"?
> It means that RK3X soc has "broken Data transfer over scheme"
Am, OK
I will use "broken-dto" for quirk, and DW_MCI_QUIRK_BROKEN_DTO for id in
the next patch.
> I will check with my board.
>
> Best Regards,
> Jaehoon Chung
>
>>
>>> And is there somewhere need to call del_timer?
>>>> Best Regards,
>>>> Jaehoon Chung
>>>>
>>>>>>> };
>>>>>>> @@ -2654,6 +2696,9 @@ int dw_mci_probe(struct dw_mci *host)
>>>>>>> spin_lock_init(&host->lock);
>>>>>>> INIT_LIST_HEAD(&host->queue);
>>>>>>> + if (host->quirks & DW_MCI_QUIRK_DTO_TIMER)
>>>>>>> + setup_timer(&host->dto_timer,
>>>>>>> + dw_mci_dto_timer, (unsigned long)host);
>>>>>>> /*
>>>>>>> * Get the host data width - this assumes that HCON has been set with
>>>>>>> diff --git a/include/linux/mmc/dw_mmc.h b/include/linux/mmc/dw_mmc.h
>>>>>>> index 42b724e..2477813 100644
>>>>>>> --- a/include/linux/mmc/dw_mmc.h
>>>>>>> +++ b/include/linux/mmc/dw_mmc.h
>>>>>>> @@ -98,6 +98,7 @@ struct mmc_data;
>>>>>>> * @irq_flags: The flags to be passed to request_irq.
>>>>>>> * @irq: The irq value to be passed to request_irq.
>>>>>>> * @sdio_id0: Number of slot0 in the SDIO interrupt registers.
>>>>>>> + * @dto_timer: Timer for data over interrupt timeout.
>>>>>>> *
>>>>>>> * Locking
>>>>>>> * =======
>>>>>>> @@ -196,6 +197,8 @@ struct dw_mci {
>>>>>>> int irq;
>>>>>>> int sdio_id0;
>>>>>>> +
>>>>>>> + struct timer_list dto_timer;
>>>>>>> };
>>>>>>> /* DMA ops for Internal/External DMAC interface */
>>>>>>> @@ -220,6 +223,8 @@ struct dw_mci_dma_ops {
>>>>>>> #define DW_MCI_QUIRK_BROKEN_CARD_DETECTION BIT(3)
>>>>>>> /* No write protect */
>>>>>>> #define DW_MCI_QUIRK_NO_WRITE_PROTECT BIT(4)
>>>>>>> +/* Timer for data over interrupt timeout */
>>>>>>> +#define DW_MCI_QUIRK_DTO_TIMER BIT(5)
>>>>>>> /* Slot level quirks */
>>>>>>> /* This slot has no write protect */
>>>>>>>
>>>>>>
>>>>>>
>>>>>
>>>>> _______________________________________________
>>>>> linux-arm-kernel mailing list
>>>>> linux-arm-kernel at lists.infradead.org
>>>>> http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
>>>>
>>>>
>>>>
>>
>
>
>
More information about the linux-arm-kernel
mailing list