[PATCH v4 15/19] arm/arm64: KVM: add virtual GICv3 distributor emulation
Christoffer Dall
christoffer.dall at linaro.org
Sun Nov 23 06:38:41 PST 2014
On Fri, Nov 14, 2014 at 10:07:59AM +0000, Andre Przywara wrote:
> With everything separated and prepared, we implement a model of a
> GICv3 distributor and redistributors by using the existing framework
> to provide handler functions for each register group.
>
> Currently we limit the emulation to a model enforcing a single
> security state, with SRE==1 (forcing system register access) and
> ARE==1 (allowing more than 8 VCPUs).
>
> We share some of the functions provided for GICv2 emulation, but take
> the different ways of addressing (v)CPUs into account.
> Save and restore is currently not implemented.
>
> Similar to the split-off of the GICv2 specific code, the new emulation
> code goes into a new file (vgic-v3-emul.c).
>
> Signed-off-by: Andre Przywara <andre.przywara at arm.com>
> ---
> Changelog v3...v4:
> - remove ICC_SGI1R_EL1 register handling (moved into later patch)
> - add definitions for single security state
what exactly does this mean?
> - document emulation limitations in vgic-v3-emul.c header
> - move CTLR, TYPER and IIDR handling into separate functions
> - add RAO/WI handling for IGROUPRn registers
> - remove unneeded offset masking on calling vgic_reg_access()
> - rework handle_mmio_route_reg() to only handle SPIs
> - refine IROUTERn register range
> - use non-atomic bitops functions (__clear_bit() and __set_bit())
> - rename vgic_dist_ranges[] to vgic_v3_dist_ranges[]
> - add (RAZ/WI) implementation of GICD_STATUSR
> - add (RAZ/WI) implementations of MBI registers
> - adapt to new private passing (in struct kvm_exit_mmio instead of a paramter)
> - fix vcpu_id calculation bug in handle CFG registers
which bug was that? I can't see the difference between v3 and v4 on
this one?
> - always use hexadecimal numbers for .len member
> - simplify vgic_v3_handle_mmio()
> - add vgic_v3_create() and vgic_v3_destroy()
> - swap vgic_v3_[sg]et_attr() code location
> - add and improve comments
> - (adaptions to changes from earlier patches)
>
> arch/arm64/kvm/Makefile | 1 +
> include/kvm/arm_vgic.h | 9 +-
> include/linux/irqchip/arm-gic-v3.h | 32 ++
> include/linux/kvm_host.h | 1 +
> include/uapi/linux/kvm.h | 2 +
> virt/kvm/arm/vgic-v3-emul.c | 904 ++++++++++++++++++++++++++++++++++++
> virt/kvm/arm/vgic.c | 11 +-
> virt/kvm/arm/vgic.h | 3 +
> 8 files changed, 960 insertions(+), 3 deletions(-)
> create mode 100644 virt/kvm/arm/vgic-v3-emul.c
>
> diff --git a/arch/arm64/kvm/Makefile b/arch/arm64/kvm/Makefile
> index d957353..4e6e09e 100644
> --- a/arch/arm64/kvm/Makefile
> +++ b/arch/arm64/kvm/Makefile
> @@ -24,5 +24,6 @@ kvm-$(CONFIG_KVM_ARM_VGIC) += $(KVM)/arm/vgic-v2.o
> kvm-$(CONFIG_KVM_ARM_VGIC) += $(KVM)/arm/vgic-v2-emul.o
> kvm-$(CONFIG_KVM_ARM_VGIC) += vgic-v2-switch.o
> kvm-$(CONFIG_KVM_ARM_VGIC) += $(KVM)/arm/vgic-v3.o
> +kvm-$(CONFIG_KVM_ARM_VGIC) += $(KVM)/arm/vgic-v3-emul.o
> kvm-$(CONFIG_KVM_ARM_VGIC) += vgic-v3-switch.o
> kvm-$(CONFIG_KVM_ARM_TIMER) += $(KVM)/arm/arch_timer.o
> diff --git a/include/kvm/arm_vgic.h b/include/kvm/arm_vgic.h
> index 421833f..c1ef5a9 100644
> --- a/include/kvm/arm_vgic.h
> +++ b/include/kvm/arm_vgic.h
> @@ -160,7 +160,11 @@ struct vgic_dist {
>
> /* Distributor and vcpu interface mapping in the guest */
> phys_addr_t vgic_dist_base;
> - phys_addr_t vgic_cpu_base;
> + /* GICv2 and GICv3 use different mapped register blocks */
> + union {
> + phys_addr_t vgic_cpu_base;
> + phys_addr_t vgic_redist_base;
> + };
>
> /* Distributor enabled */
> u32 enabled;
> @@ -222,6 +226,9 @@ struct vgic_dist {
> */
> struct vgic_bitmap *irq_spi_target;
>
> + /* Target MPIDR for each IRQ (needed for GICv3 IROUTERn) only */
> + u32 *irq_spi_mpidr;
> +
> /* Bitmap indicating which CPU has something pending */
> unsigned long *irq_pending_on_cpu;
>
> diff --git a/include/linux/irqchip/arm-gic-v3.h b/include/linux/irqchip/arm-gic-v3.h
> index 03a4ea3..726d898 100644
> --- a/include/linux/irqchip/arm-gic-v3.h
> +++ b/include/linux/irqchip/arm-gic-v3.h
> @@ -33,6 +33,7 @@
> #define GICD_SETSPI_SR 0x0050
> #define GICD_CLRSPI_SR 0x0058
> #define GICD_SEIR 0x0068
> +#define GICD_IGROUPR 0x0080
> #define GICD_ISENABLER 0x0100
> #define GICD_ICENABLER 0x0180
> #define GICD_ISPENDR 0x0200
> @@ -41,14 +42,37 @@
> #define GICD_ICACTIVER 0x0380
> #define GICD_IPRIORITYR 0x0400
> #define GICD_ICFGR 0x0C00
> +#define GICD_IGRPMODR 0x0D00
> +#define GICD_NSACR 0x0E00
> #define GICD_IROUTER 0x6000
> +#define GICD_IDREGS 0xFFD0
> #define GICD_PIDR2 0xFFE8
>
> +/*
> + * Those registers are actually from GICv2, but the spec demands that they
> + * are implemented as RES0 if ARE is 1 (which we do in KVM's emulated GICv3).
> + */
> +#define GICD_ITARGETSR 0x0800
> +#define GICD_SGIR 0x0F00
> +#define GICD_CPENDSGIR 0x0F10
> +#define GICD_SPENDSGIR 0x0F20
> +
> #define GICD_CTLR_RWP (1U << 31)
> +#define GICD_CTLR_DS (1U << 6)
> #define GICD_CTLR_ARE_NS (1U << 4)
> #define GICD_CTLR_ENABLE_G1A (1U << 1)
> #define GICD_CTLR_ENABLE_G1 (1U << 0)
>
> +/*
> + * In systems with a single security state (what we emulate in KVM)
> + * the meaning of the interrupt group enable bits is slightly different
> + */
> +#define GICD_CTLR_ENABLE_SS_G1 (1U << 1)
> +#define GICD_CTLR_ENABLE_SS_G0 (1U << 0)
> +
> +#define GICD_TYPER_LPIS (1U << 17)
> +#define GICD_TYPER_MBIS (1U << 16)
> +
> #define GICD_IROUTER_SPI_MODE_ONE (0U << 31)
> #define GICD_IROUTER_SPI_MODE_ANY (1U << 31)
>
> @@ -56,6 +80,8 @@
> #define GIC_PIDR2_ARCH_GICv3 0x30
> #define GIC_PIDR2_ARCH_GICv4 0x40
>
> +#define GIC_V3_DIST_SIZE 0x10000
> +
> /*
> * Re-Distributor registers, offsets from RD_base
> */
> @@ -74,6 +100,7 @@
> #define GICR_SYNCR 0x00C0
> #define GICR_MOVLPIR 0x0100
> #define GICR_MOVALLR 0x0110
> +#define GICR_IDREGS GICD_IDREGS
> #define GICR_PIDR2 GICD_PIDR2
>
> #define GICR_WAKER_ProcessorSleep (1U << 1)
> @@ -82,6 +109,7 @@
> /*
> * Re-Distributor registers, offsets from SGI_base
> */
> +#define GICR_IGROUPR0 GICD_IGROUPR
> #define GICR_ISENABLER0 GICD_ISENABLER
> #define GICR_ICENABLER0 GICD_ICENABLER
> #define GICR_ISPENDR0 GICD_ISPENDR
> @@ -90,10 +118,14 @@
> #define GICR_ICACTIVER0 GICD_ICACTIVER
> #define GICR_IPRIORITYR0 GICD_IPRIORITYR
> #define GICR_ICFGR0 GICD_ICFGR
> +#define GICR_IGRPMODR0 GICD_IGRPMODR
> +#define GICR_NSACR GICD_NSACR
>
> #define GICR_TYPER_VLPIS (1U << 1)
> #define GICR_TYPER_LAST (1U << 4)
>
> +#define GIC_V3_REDIST_SIZE 0x20000
> +
> /*
> * CPU interface registers
> */
> diff --git a/include/linux/kvm_host.h b/include/linux/kvm_host.h
> index 326ba7a..4a7798e 100644
> --- a/include/linux/kvm_host.h
> +++ b/include/linux/kvm_host.h
> @@ -1085,6 +1085,7 @@ void kvm_unregister_device_ops(u32 type);
> extern struct kvm_device_ops kvm_mpic_ops;
> extern struct kvm_device_ops kvm_xics_ops;
> extern struct kvm_device_ops kvm_arm_vgic_v2_ops;
> +extern struct kvm_device_ops kvm_arm_vgic_v3_ops;
>
> #ifdef CONFIG_HAVE_KVM_CPU_RELAX_INTERCEPT
>
> diff --git a/include/uapi/linux/kvm.h b/include/uapi/linux/kvm.h
> index 6076882..24cb129 100644
> --- a/include/uapi/linux/kvm.h
> +++ b/include/uapi/linux/kvm.h
> @@ -960,6 +960,8 @@ enum kvm_device_type {
> #define KVM_DEV_TYPE_ARM_VGIC_V2 KVM_DEV_TYPE_ARM_VGIC_V2
> KVM_DEV_TYPE_FLIC,
> #define KVM_DEV_TYPE_FLIC KVM_DEV_TYPE_FLIC
> + KVM_DEV_TYPE_ARM_VGIC_V3,
> +#define KVM_DEV_TYPE_ARM_VGIC_V3 KVM_DEV_TYPE_ARM_VGIC_V3
> KVM_DEV_TYPE_MAX,
> };
>
> diff --git a/virt/kvm/arm/vgic-v3-emul.c b/virt/kvm/arm/vgic-v3-emul.c
> new file mode 100644
> index 0000000..97b5801
> --- /dev/null
> +++ b/virt/kvm/arm/vgic-v3-emul.c
> @@ -0,0 +1,904 @@
> +/*
> + * GICv3 distributor and redistributor emulation
> + *
> + * GICv3 emulation is currently only supported on a GICv3 host (because
> + * we rely on the hardware's CPU interface virtualization support), but
> + * supports both hardware with or without the optional GICv2 backwards
> + * compatibility features.
> + *
> + * Limitations of the emulation:
> + * (RAZ/WI: read as zero, write ignore, RAO/WI: read as one, write ignore)
> + * - We do not support LPIs (yet). TYPER.LPIS is reported as 0 and is RAZ/WI.
> + * - We do not support the message based interrupts (MBIs) triggered by
> + * writes to the GICD_{SET,CLR}SPI_* registers. TYPER.MBIS is reported as 0.
> + * - We do not support the (optional) backwards compatibility feature.
> + * GICD_CTLR.ARE resets to 1 and is RAO/WI. If the _host_ GIC supports
> + * the compatiblity feature, you can use a GICv2 in the guest, though.
> + * - We only support a single security state. GICD_CTLR.DS is 1 and is RAO/WI.
> + * - Priorities are not emulated (same as the GICv2 emulation). Linux
> + * as a guest is fine with this, because it does not use priorities.
> + * - We only support Group1 interrupts. Again Linux uses only those.
> + *
> + * Copyright (C) 2014 ARM Ltd.
> + * Author: Andre Przywara <andre.przywara at arm.com>
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License version 2 as
> + * published by the Free Software Foundation.
> + *
> + * This program is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + *
> + * You should have received a copy of the GNU General Public License
> + * along with this program. If not, see <http://www.gnu.org/licenses/>.
> + */
> +
> +#include <linux/cpu.h>
> +#include <linux/kvm.h>
> +#include <linux/kvm_host.h>
> +#include <linux/interrupt.h>
> +
> +#include <linux/irqchip/arm-gic-v3.h>
> +#include <kvm/arm_vgic.h>
> +
> +#include <asm/kvm_emulate.h>
> +#include <asm/kvm_arm.h>
> +#include <asm/kvm_mmu.h>
> +
> +#include "vgic.h"
> +
> +static bool handle_mmio_rao_wi(struct kvm_vcpu *vcpu,
> + struct kvm_exit_mmio *mmio, phys_addr_t offset)
> +{
> + u32 reg = 0xffffffff;
> +
> + vgic_reg_access(mmio, ®, offset,
> + ACCESS_READ_VALUE | ACCESS_WRITE_IGNORED);
> +
> + return false;
> +}
> +
> +static bool handle_mmio_ctlr(struct kvm_vcpu *vcpu,
> + struct kvm_exit_mmio *mmio, phys_addr_t offset)
> +{
> + u32 reg = 0;
> +
> + /*
> + * Force ARE and DS to 1, the guest cannot change this.
> + * For the time being we only support Group1 interrupts.
> + */
> + if (vcpu->kvm->arch.vgic.enabled)
> + reg = GICD_CTLR_ENABLE_SS_G1;
> + reg |= GICD_CTLR_ARE_NS | GICD_CTLR_DS;
> +
> + vgic_reg_access(mmio, ®, offset,
> + ACCESS_READ_VALUE | ACCESS_WRITE_VALUE);
> + if (mmio->is_write) {
> + if (reg & GICD_CTLR_ENABLE_SS_G0)
> + kvm_info("guest tried to enable unsupported Group0 interrupts\n");
> + vcpu->kvm->arch.vgic.enabled = !!(reg & GICD_CTLR_ENABLE_SS_G1);
> + vgic_update_state(vcpu->kvm);
> + return true;
> + }
> + return false;
> +}
> +
> +/*
> + * As this implementation does not provide compatibility
> + * with GICv2 (ARE==1), we report zero CPUs in bits [5..7].
> + * Also LPIs and MBIs are not supported, so we set the respective bits to 0.
> + * Also we report at most 2**10=1024 interrupt IDs (to match 1024 SPIs).
> + */
> +#define INTERRUPT_ID_BITS 10
> +static bool handle_mmio_typer(struct kvm_vcpu *vcpu,
> + struct kvm_exit_mmio *mmio, phys_addr_t offset)
> +{
> + u32 reg;
> +
> + /* we report at most 1024 IRQs via this interface */
hmmm, do we need to repeat ourselves here?
I get a bit confused by both the comment above and here, as to *why* we
are reporting this value? And what is the bit about 'this interface'?
Is there another interface.
Perhaps what you're trying to get at here are the semantic differences
between ITLinesNumber and IDbits and how that helps a reader understand
the code.
> + reg = (min(vcpu->kvm->arch.vgic.nr_irqs, 1024) >> 5) - 1;
> +
> + reg |= (INTERRUPT_ID_BITS - 1) << 19;
> +
> + vgic_reg_access(mmio, ®, offset,
> + ACCESS_READ_VALUE | ACCESS_WRITE_IGNORED);
> +
> + return false;
> +}
> +
> +static bool handle_mmio_iidr(struct kvm_vcpu *vcpu,
> + struct kvm_exit_mmio *mmio, phys_addr_t offset)
> +{
> + u32 reg;
> +
> + reg = (PRODUCT_ID_KVM << 24) | (IMPLEMENTER_ARM << 0);
> + vgic_reg_access(mmio, ®, offset,
> + ACCESS_READ_VALUE | ACCESS_WRITE_IGNORED);
> +
> + return false;
> +}
> +
> +static bool handle_mmio_set_enable_reg_dist(struct kvm_vcpu *vcpu,
> + struct kvm_exit_mmio *mmio,
> + phys_addr_t offset)
> +{
> + if (likely(offset >= VGIC_NR_PRIVATE_IRQS / 8))
> + return vgic_handle_enable_reg(vcpu->kvm, mmio, offset,
> + vcpu->vcpu_id,
> + ACCESS_WRITE_SETBIT);
> +
> + vgic_reg_access(mmio, NULL, offset,
> + ACCESS_READ_RAZ | ACCESS_WRITE_IGNORED);
> + return false;
> +}
> +
> +static bool handle_mmio_clear_enable_reg_dist(struct kvm_vcpu *vcpu,
> + struct kvm_exit_mmio *mmio,
> + phys_addr_t offset)
> +{
> + if (likely(offset >= VGIC_NR_PRIVATE_IRQS / 8))
> + return vgic_handle_enable_reg(vcpu->kvm, mmio, offset,
> + vcpu->vcpu_id,
> + ACCESS_WRITE_CLEARBIT);
> +
> + vgic_reg_access(mmio, NULL, offset,
> + ACCESS_READ_RAZ | ACCESS_WRITE_IGNORED);
> + return false;
> +}
> +
> +static bool handle_mmio_set_pending_reg_dist(struct kvm_vcpu *vcpu,
> + struct kvm_exit_mmio *mmio,
> + phys_addr_t offset)
> +{
> + if (likely(offset >= VGIC_NR_PRIVATE_IRQS / 8))
> + return vgic_handle_set_pending_reg(vcpu->kvm, mmio, offset,
> + vcpu->vcpu_id);
> +
> + vgic_reg_access(mmio, NULL, offset,
> + ACCESS_READ_RAZ | ACCESS_WRITE_IGNORED);
> + return false;
> +}
> +
> +static bool handle_mmio_clear_pending_reg_dist(struct kvm_vcpu *vcpu,
> + struct kvm_exit_mmio *mmio,
> + phys_addr_t offset)
> +{
> + if (likely(offset >= VGIC_NR_PRIVATE_IRQS / 8))
> + return vgic_handle_clear_pending_reg(vcpu->kvm, mmio, offset,
> + vcpu->vcpu_id);
> +
> + vgic_reg_access(mmio, NULL, offset,
> + ACCESS_READ_RAZ | ACCESS_WRITE_IGNORED);
> + return false;
> +}
> +
> +static bool handle_mmio_priority_reg_dist(struct kvm_vcpu *vcpu,
> + struct kvm_exit_mmio *mmio,
> + phys_addr_t offset)
> +{
> + u32 *reg;
> +
> + if (unlikely(offset < VGIC_NR_PRIVATE_IRQS)) {
> + vgic_reg_access(mmio, NULL, offset,
> + ACCESS_READ_RAZ | ACCESS_WRITE_IGNORED);
> + return false;
> + }
> +
> + reg = vgic_bytemap_get_reg(&vcpu->kvm->arch.vgic.irq_priority,
> + vcpu->vcpu_id, offset);
> + vgic_reg_access(mmio, reg, offset,
> + ACCESS_READ_VALUE | ACCESS_WRITE_VALUE);
> + return false;
> +}
> +
> +static bool handle_mmio_cfg_reg_dist(struct kvm_vcpu *vcpu,
> + struct kvm_exit_mmio *mmio,
> + phys_addr_t offset)
> +{
> + u32 *reg;
> +
> + if (unlikely(offset < VGIC_NR_PRIVATE_IRQS / 4)) {
> + vgic_reg_access(mmio, NULL, offset,
> + ACCESS_READ_RAZ | ACCESS_WRITE_IGNORED);
> + return false;
> + }
> +
> + reg = vgic_bitmap_get_reg(&vcpu->kvm->arch.vgic.irq_cfg,
> + vcpu->vcpu_id, offset >> 1);
> +
> + return vgic_handle_cfg_reg(reg, mmio, offset);
> +}
> +
> +/*
> + * We use a compressed version of the MPIDR (all 32 bits in one 32-bit word)
> + * when we store the target MPIDR written by the guest.
> + */
> +static u32 compress_mpidr(unsigned long mpidr)
> +{
> + u32 ret;
> +
> + ret = MPIDR_AFFINITY_LEVEL(mpidr, 0);
> + ret |= MPIDR_AFFINITY_LEVEL(mpidr, 1) << 8;
> + ret |= MPIDR_AFFINITY_LEVEL(mpidr, 2) << 16;
> + ret |= MPIDR_AFFINITY_LEVEL(mpidr, 3) << 24;
> +
> + return ret;
> +}
> +
> +static unsigned long uncompress_mpidr(u32 value)
> +{
> + unsigned long mpidr;
> +
> + mpidr = ((value >> 0) & 0xFF) << MPIDR_LEVEL_SHIFT(0);
> + mpidr |= ((value >> 8) & 0xFF) << MPIDR_LEVEL_SHIFT(1);
> + mpidr |= ((value >> 16) & 0xFF) << MPIDR_LEVEL_SHIFT(2);
> + mpidr |= (u64)((value >> 24) & 0xFF) << MPIDR_LEVEL_SHIFT(3);
> +
> + return mpidr;
> +}
> +
> +/*
> + * Lookup the given MPIDR value to get the vcpu_id (if there is one)
> + * and store that in the irq_spi_cpu[] array.
> + * This limits the number of VCPUs to 255 for now, extending the data
> + * type (or storing kvm_vcpu poiners) should lift the limit.
s/poiners/pointers
> + * Store the original MPIDR value in an extra array to support read-as-written.
> + * Unallocated MPIDRs are translated to a special value and caught
> + * before any array accesses.
We may have covered this already, but why can't we restore the original
MPIDR based on the the irq_spi_cpu array?
Is that because we loose information about 'which' unallocated MPIDR was
written? If that's the case, it seems weird that we go through the
trouble but we anyway throw away the aff3 field...?
> + */
> +static bool handle_mmio_route_reg(struct kvm_vcpu *vcpu,
> + struct kvm_exit_mmio *mmio,
> + phys_addr_t offset)
> +{
> + struct kvm *kvm = vcpu->kvm;
> + struct vgic_dist *dist = &kvm->arch.vgic;
> + int spi;
> + u32 reg;
> + int vcpu_id;
> + unsigned long *bmap, mpidr;
> +
> + /*
> + * The upper 32 bits of each 64 bit register are zero,
> + * as we don't support Aff3.
> + */
> + if ((offset & 4)) {
> + vgic_reg_access(mmio, NULL, offset,
> + ACCESS_READ_RAZ | ACCESS_WRITE_IGNORED);
> + return false;
> + }
> +
> + /* This region only covers SPIs, so no handling of private IRQs here. */
> + spi = offset / 8;
that's not how I read the spec, it says that GICD_IROUTER0 to
GICD_IROUTER1 are not implemented (because they are SGIs and PPIs), and
I read the 'SPI ID m' as the lowest numbered SPI ID being 32, thus you
should do:
spi = offset / 8 - VGIC_NR_PRIVATE_IRQS;
> +
> + /* get the stored MPIDR for this IRQ */
> + mpidr = uncompress_mpidr(dist->irq_spi_mpidr[spi]);
> + mpidr &= MPIDR_HWID_BITMASK;
is this mask needed after calling uncompress above?
> + reg = mpidr;
> +
> + vgic_reg_access(mmio, ®, offset,
> + ACCESS_READ_VALUE | ACCESS_WRITE_VALUE);
> +
> + if (!mmio->is_write)
> + return false;
> +
> + /*
> + * Now clear the currently assigned vCPU from the map, making room
> + * for the new one to be written below
> + */
> + vcpu = kvm_mpidr_to_vcpu(kvm, mpidr);
> + if (likely(vcpu)) {
> + vcpu_id = vcpu->vcpu_id;
> + bmap = vgic_bitmap_get_shared_map(&dist->irq_spi_target[vcpu_id]);
> + __clear_bit(spi, bmap);
> + }
> +
> + dist->irq_spi_mpidr[spi] = compress_mpidr(reg);
> + vcpu = kvm_mpidr_to_vcpu(kvm, reg & MPIDR_HWID_BITMASK);
> +
> + /*
> + * The spec says that non-existent MPIDR values should not be
> + * forwarded to any existent (v)CPU, but should be able to become
> + * pending anyway. We simply keep the irq_spi_target[] array empty, so
> + * the interrupt will never be injected.
> + * irq_spi_cpu[irq] gets a magic value in this case.
> + */
> + if (likely(vcpu)) {
> + vcpu_id = vcpu->vcpu_id;
> + dist->irq_spi_cpu[spi] = vcpu_id;
> + bmap = vgic_bitmap_get_shared_map(&dist->irq_spi_target[vcpu_id]);
> + __set_bit(spi, bmap);
> + } else {
> + dist->irq_spi_cpu[spi] = VCPU_NOT_ALLOCATED;
> + }
> +
> + vgic_update_state(kvm);
> +
> + return true;
> +}
> +
> +/*
> + * We should be careful about promising too much when a guest reads
> + * this register. Don't claim to be like any hardware implementation,
> + * but just report the GIC as version 3 - which is what a Linux guest
> + * would check.
> + */
> +static bool handle_mmio_idregs(struct kvm_vcpu *vcpu,
> + struct kvm_exit_mmio *mmio,
> + phys_addr_t offset)
> +{
> + u32 reg = 0;
> +
> + switch (offset + GICD_IDREGS) {
> + case GICD_PIDR2:
> + reg = 0x3b;
> + break;
> + }
> +
> + vgic_reg_access(mmio, ®, offset,
> + ACCESS_READ_VALUE | ACCESS_WRITE_IGNORED);
> +
> + return false;
> +}
> +
> +static const struct kvm_mmio_range vgic_v3_dist_ranges[] = {
> + {
> + .base = GICD_CTLR,
> + .len = 0x04,
> + .bits_per_irq = 0,
> + .handle_mmio = handle_mmio_ctlr,
> + },
> + {
> + .base = GICD_TYPER,
> + .len = 0x04,
> + .bits_per_irq = 0,
> + .handle_mmio = handle_mmio_typer,
> + },
> + {
> + .base = GICD_IIDR,
> + .len = 0x04,
> + .bits_per_irq = 0,
> + .handle_mmio = handle_mmio_iidr,
> + },
> + {
> + /* this register is optional, it is RAZ/WI if not implemented */
> + .base = GICD_STATUSR,
> + .len = 0x04,
> + .bits_per_irq = 0,
> + .handle_mmio = handle_mmio_raz_wi,
> + },
> + {
> + /* this write only register is WI when TYPER.MBIS=0 */
> + .base = GICD_SETSPI_NSR,
> + .len = 0x04,
> + .bits_per_irq = 0,
> + .handle_mmio = handle_mmio_raz_wi,
> + },
> + {
> + /* this write only register is WI when TYPER.MBIS=0 */
> + .base = GICD_CLRSPI_NSR,
> + .len = 0x04,
> + .bits_per_irq = 0,
> + .handle_mmio = handle_mmio_raz_wi,
> + },
> + {
> + /* this is RAZ/WI when DS=1 */
> + .base = GICD_SETSPI_SR,
> + .len = 0x04,
> + .bits_per_irq = 0,
> + .handle_mmio = handle_mmio_raz_wi,
> + },
> + {
> + /* this is RAZ/WI when DS=1 */
> + .base = GICD_CLRSPI_SR,
> + .len = 0x04,
> + .bits_per_irq = 0,
> + .handle_mmio = handle_mmio_raz_wi,
> + },
> + {
> + .base = GICD_IGROUPR,
> + .len = 0x80,
> + .bits_per_irq = 1,
> + .handle_mmio = handle_mmio_rao_wi,
> + },
> + {
> + .base = GICD_ISENABLER,
> + .len = 0x80,
> + .bits_per_irq = 1,
> + .handle_mmio = handle_mmio_set_enable_reg_dist,
> + },
> + {
> + .base = GICD_ICENABLER,
> + .len = 0x80,
> + .bits_per_irq = 1,
> + .handle_mmio = handle_mmio_clear_enable_reg_dist,
> + },
> + {
> + .base = GICD_ISPENDR,
> + .len = 0x80,
> + .bits_per_irq = 1,
> + .handle_mmio = handle_mmio_set_pending_reg_dist,
> + },
> + {
> + .base = GICD_ICPENDR,
> + .len = 0x80,
> + .bits_per_irq = 1,
> + .handle_mmio = handle_mmio_clear_pending_reg_dist,
> + },
> + {
> + .base = GICD_ISACTIVER,
> + .len = 0x80,
> + .bits_per_irq = 1,
> + .handle_mmio = handle_mmio_raz_wi,
> + },
> + {
> + .base = GICD_ICACTIVER,
> + .len = 0x80,
> + .bits_per_irq = 1,
> + .handle_mmio = handle_mmio_raz_wi,
> + },
> + {
> + .base = GICD_IPRIORITYR,
> + .len = 0x400,
> + .bits_per_irq = 8,
> + .handle_mmio = handle_mmio_priority_reg_dist,
> + },
> + {
> + /* TARGETSRn is RES0 when ARE=1 */
> + .base = GICD_ITARGETSR,
> + .len = 0x400,
> + .bits_per_irq = 8,
> + .handle_mmio = handle_mmio_raz_wi,
> + },
> + {
> + .base = GICD_ICFGR,
> + .len = 0x100,
> + .bits_per_irq = 2,
> + .handle_mmio = handle_mmio_cfg_reg_dist,
> + },
> + {
> + /* this is RAZ/WI when DS=1 */
> + .base = GICD_IGRPMODR,
> + .len = 0x80,
> + .bits_per_irq = 1,
> + .handle_mmio = handle_mmio_raz_wi,
> + },
> + {
> + /* this is RAZ/WI when DS=1 */
> + .base = GICD_NSACR,
> + .len = 0x100,
> + .bits_per_irq = 2,
> + .handle_mmio = handle_mmio_raz_wi,
> + },
> + {
> + /* this is RAZ/WI when ARE=1 */
> + .base = GICD_SGIR,
> + .len = 0x04,
> + .handle_mmio = handle_mmio_raz_wi,
> + },
> + {
> + /* this is RAZ/WI when ARE=1 */
> + .base = GICD_CPENDSGIR,
> + .len = 0x10,
> + .handle_mmio = handle_mmio_raz_wi,
> + },
> + {
> + /* this is RAZ/WI when ARE=1 */
> + .base = GICD_SPENDSGIR,
> + .len = 0x10,
> + .handle_mmio = handle_mmio_raz_wi,
> + },
> + {
> + .base = GICD_IROUTER + 0x100,
> + .len = 0x1edc,
> + .bits_per_irq = 64,
> + .handle_mmio = handle_mmio_route_reg,
> + },
> + {
> + .base = GICD_IDREGS,
> + .len = 0x30,
> + .bits_per_irq = 0,
> + .handle_mmio = handle_mmio_idregs,
> + },
> + {},
> +};
> +
> +static bool handle_mmio_set_enable_reg_redist(struct kvm_vcpu *vcpu,
> + struct kvm_exit_mmio *mmio,
> + phys_addr_t offset)
> +{
> + struct kvm_vcpu *redist_vcpu = mmio->private;
> +
> + return vgic_handle_enable_reg(vcpu->kvm, mmio, offset,
> + redist_vcpu->vcpu_id,
> + ACCESS_WRITE_SETBIT);
> +}
> +
> +static bool handle_mmio_clear_enable_reg_redist(struct kvm_vcpu *vcpu,
> + struct kvm_exit_mmio *mmio,
> + phys_addr_t offset)
> +{
> + struct kvm_vcpu *redist_vcpu = mmio->private;
> +
> + return vgic_handle_enable_reg(vcpu->kvm, mmio, offset,
> + redist_vcpu->vcpu_id,
> + ACCESS_WRITE_CLEARBIT);
> +}
> +
> +static bool handle_mmio_set_pending_reg_redist(struct kvm_vcpu *vcpu,
> + struct kvm_exit_mmio *mmio,
> + phys_addr_t offset)
> +{
> + struct kvm_vcpu *redist_vcpu = mmio->private;
> +
> + return vgic_handle_set_pending_reg(vcpu->kvm, mmio, offset,
> + redist_vcpu->vcpu_id);
> +}
> +
> +static bool handle_mmio_clear_pending_reg_redist(struct kvm_vcpu *vcpu,
> + struct kvm_exit_mmio *mmio,
> + phys_addr_t offset)
> +{
> + struct kvm_vcpu *redist_vcpu = mmio->private;
> +
> + return vgic_handle_clear_pending_reg(vcpu->kvm, mmio, offset,
> + redist_vcpu->vcpu_id);
> +}
> +
> +static bool handle_mmio_priority_reg_redist(struct kvm_vcpu *vcpu,
> + struct kvm_exit_mmio *mmio,
> + phys_addr_t offset)
> +{
> + struct kvm_vcpu *redist_vcpu = mmio->private;
> + u32 *reg;
> +
> + reg = vgic_bytemap_get_reg(&vcpu->kvm->arch.vgic.irq_priority,
> + redist_vcpu->vcpu_id, offset);
> + vgic_reg_access(mmio, reg, offset,
> + ACCESS_READ_VALUE | ACCESS_WRITE_VALUE);
> + return false;
> +}
> +
> +static bool handle_mmio_cfg_reg_redist(struct kvm_vcpu *vcpu,
> + struct kvm_exit_mmio *mmio,
> + phys_addr_t offset)
> +{
> + struct kvm_vcpu *redist_vcpu = mmio->private;
> +
> + u32 *reg = vgic_bitmap_get_reg(&vcpu->kvm->arch.vgic.irq_cfg,
> + redist_vcpu->vcpu_id, offset >> 1);
> +
> + return vgic_handle_cfg_reg(reg, mmio, offset);
> +}
> +
> +static const struct kvm_mmio_range vgic_redist_sgi_ranges[] = {
> + {
> + .base = GICR_IGROUPR0,
> + .len = 0x04,
> + .bits_per_irq = 1,
> + .handle_mmio = handle_mmio_raz_wi,
I think you were going to change this ro handle_mmio_rao_wi() instead?
> + },
> + {
> + .base = GICR_ISENABLER0,
> + .len = 0x04,
> + .bits_per_irq = 1,
> + .handle_mmio = handle_mmio_set_enable_reg_redist,
> + },
> + {
> + .base = GICR_ICENABLER0,
> + .len = 0x04,
> + .bits_per_irq = 1,
> + .handle_mmio = handle_mmio_clear_enable_reg_redist,
> + },
> + {
> + .base = GICR_ISPENDR0,
> + .len = 0x04,
> + .bits_per_irq = 1,
> + .handle_mmio = handle_mmio_set_pending_reg_redist,
> + },
> + {
> + .base = GICR_ICPENDR0,
> + .len = 0x04,
> + .bits_per_irq = 1,
> + .handle_mmio = handle_mmio_clear_pending_reg_redist,
> + },
> + {
> + .base = GICR_ISACTIVER0,
> + .len = 0x04,
> + .bits_per_irq = 1,
> + .handle_mmio = handle_mmio_raz_wi,
> + },
> + {
> + .base = GICR_ICACTIVER0,
> + .len = 0x04,
> + .bits_per_irq = 1,
> + .handle_mmio = handle_mmio_raz_wi,
> + },
> + {
> + .base = GICR_IPRIORITYR0,
> + .len = 0x20,
> + .bits_per_irq = 8,
> + .handle_mmio = handle_mmio_priority_reg_redist,
> + },
> + {
> + .base = GICR_ICFGR0,
> + .len = 0x08,
> + .bits_per_irq = 2,
> + .handle_mmio = handle_mmio_cfg_reg_redist,
> + },
> + {
> + .base = GICR_IGRPMODR0,
> + .len = 0x04,
> + .bits_per_irq = 1,
> + .handle_mmio = handle_mmio_raz_wi,
> + },
> + {
> + .base = GICR_NSACR,
> + .len = 0x04,
> + .handle_mmio = handle_mmio_raz_wi,
> + },
> + {},
> +};
> +
> +static bool handle_mmio_ctlr_redist(struct kvm_vcpu *vcpu,
> + struct kvm_exit_mmio *mmio,
> + phys_addr_t offset)
> +{
> + /* since we don't support LPIs, this register is zero for now */
> + vgic_reg_access(mmio, NULL, offset,
> + ACCESS_READ_RAZ | ACCESS_WRITE_IGNORED);
> + return false;
> +}
> +
> +static bool handle_mmio_typer_redist(struct kvm_vcpu *vcpu,
> + struct kvm_exit_mmio *mmio,
> + phys_addr_t offset)
> +{
> + u32 reg;
> + u64 mpidr;
> + struct kvm_vcpu *redist_vcpu = mmio->private;
> + int target_vcpu_id = redist_vcpu->vcpu_id;
> +
> + /* the upper 32 bits contain the affinity value */
> + if ((offset & ~3) == 4) {
> + mpidr = kvm_vcpu_get_mpidr_aff(redist_vcpu);
> + reg = compress_mpidr(mpidr);
> +
> + vgic_reg_access(mmio, ®, offset,
> + ACCESS_READ_VALUE | ACCESS_WRITE_IGNORED);
> + return false;
> + }
> +
> + reg = redist_vcpu->vcpu_id << 8;
> + if (target_vcpu_id == atomic_read(&vcpu->kvm->online_vcpus) - 1)
> + reg |= GICR_TYPER_LAST;
> + vgic_reg_access(mmio, ®, offset,
> + ACCESS_READ_VALUE | ACCESS_WRITE_IGNORED);
> + return false;
> +}
> +
> +static const struct kvm_mmio_range vgic_redist_ranges[] = {
> + {
> + .base = GICR_CTLR,
> + .len = 0x04,
> + .bits_per_irq = 0,
> + .handle_mmio = handle_mmio_ctlr_redist,
> + },
> + {
> + .base = GICR_TYPER,
> + .len = 0x08,
> + .bits_per_irq = 0,
> + .handle_mmio = handle_mmio_typer_redist,
> + },
> + {
> + .base = GICR_IIDR,
> + .len = 0x04,
> + .bits_per_irq = 0,
> + .handle_mmio = handle_mmio_iidr,
> + },
> + {
> + .base = GICR_WAKER,
> + .len = 0x04,
> + .bits_per_irq = 0,
> + .handle_mmio = handle_mmio_raz_wi,
> + },
> + {
> + .base = GICR_IDREGS,
> + .len = 0x30,
> + .bits_per_irq = 0,
> + .handle_mmio = handle_mmio_idregs,
> + },
> + {},
> +};
> +
> +/*
> + * This function splits accesses between the distributor and the two
> + * redistributor parts (private/SPI). As each redistributor is accessible
> + * from any CPU, we have to determine the affected VCPU by taking the faulting
> + * address into account. We then pass this VCPU to the handler function via
> + * the private parameter.
> + */
> +#define SGI_BASE_OFFSET SZ_64K
> +static bool vgic_v3_handle_mmio(struct kvm_vcpu *vcpu, struct kvm_run *run,
> + struct kvm_exit_mmio *mmio)
> +{
> + struct vgic_dist *dist = &vcpu->kvm->arch.vgic;
> + unsigned long dbase = dist->vgic_dist_base;
> + unsigned long rdbase = dist->vgic_redist_base;
> + int nrcpus = atomic_read(&vcpu->kvm->online_vcpus);
> + int vcpu_id;
> + const struct kvm_mmio_range *mmio_range;
> +
> + if (is_in_range(mmio->phys_addr, mmio->len, dbase, GIC_V3_DIST_SIZE)) {
> + return vgic_handle_mmio_range(vcpu, run, mmio,
> + vgic_v3_dist_ranges, dbase);
> + }
> +
> + if (!is_in_range(mmio->phys_addr, mmio->len, rdbase,
> + GIC_V3_REDIST_SIZE * nrcpus))
> + return false;
Did you think more about the contiguous allocation issue here or can you
give me a pointer to the requirement in the spec?
> +
> + vcpu_id = (mmio->phys_addr - rdbase) / GIC_V3_REDIST_SIZE;
> + rdbase += (vcpu_id * GIC_V3_REDIST_SIZE);
> + mmio->private = kvm_get_vcpu(vcpu->kvm, vcpu_id);
> +
> + if (mmio->phys_addr >= rdbase + SGI_BASE_OFFSET) {
> + rdbase += SGI_BASE_OFFSET;
> + mmio_range = vgic_redist_sgi_ranges;
> + } else {
> + mmio_range = vgic_redist_ranges;
> + }
> + return vgic_handle_mmio_range(vcpu, run, mmio, mmio_range, rdbase);
> +}
> +
> +static bool vgic_v3_queue_sgi(struct kvm_vcpu *vcpu, int irq)
> +{
> + if (vgic_queue_irq(vcpu, 0, irq)) {
> + vgic_dist_irq_clear_pending(vcpu, irq);
> + vgic_cpu_irq_clear(vcpu, irq);
> + return true;
> + }
> +
> + return false;
> +}
> +
> +static int vgic_v3_init_maps(struct vgic_dist *dist)
> +{
> + int nr_spis = dist->nr_irqs - VGIC_NR_PRIVATE_IRQS;
> +
> + dist->irq_spi_mpidr = kcalloc(nr_spis, sizeof(dist->irq_spi_mpidr[0]),
> + GFP_KERNEL);
> +
> + if (!dist->irq_spi_mpidr)
> + return -ENOMEM;
> +
> + return 0;
> +}
> +
> +static int vgic_v3_init(struct kvm *kvm, const struct vgic_params *params)
> +{
> + struct vgic_dist *dist = &kvm->arch.vgic;
> + int ret, i;
> + u32 mpidr;
> +
> + if (IS_VGIC_ADDR_UNDEF(dist->vgic_dist_base) ||
> + IS_VGIC_ADDR_UNDEF(dist->vgic_redist_base)) {
> + kvm_err("Need to set vgic distributor addresses first\n");
> + return -ENXIO;
> + }
> +
> + /*
> + * FIXME: this should be moved to init_maps time, and may bite
> + * us when adding save/restore. Add a per-emulation hook?
> + */
progress on this fixme?
> + ret = vgic_v3_init_maps(dist);
> + if (ret) {
> + kvm_err("Unable to allocate maps\n");
> + return ret;
> + }
> +
> + /* Initialize the target VCPUs for each IRQ to VCPU 0 */
> + mpidr = compress_mpidr(kvm_vcpu_get_mpidr_aff(kvm_get_vcpu(kvm, 0)));
> + for (i = VGIC_NR_PRIVATE_IRQS; i < dist->nr_irqs; i++) {
> + dist->irq_spi_cpu[i - VGIC_NR_PRIVATE_IRQS] = 0;
> + dist->irq_spi_mpidr[i - VGIC_NR_PRIVATE_IRQS] = mpidr;
> + vgic_bitmap_set_irq_val(dist->irq_spi_target, 0, i, 1);
> + }
> +
> + return 0;
> +}
> +
> +/* GICv3 does not keep track of SGI sources anymore. */
> +static void vgic_v3_add_sgi_source(struct kvm_vcpu *vcpu, int irq, int source)
> +{
> +}
> +
> +int vgic_v3_init_emulation(struct kvm *kvm)
> +{
> + struct vgic_dist *dist = &kvm->arch.vgic;
> +
> + dist->vm_ops.handle_mmio = vgic_v3_handle_mmio;
> + dist->vm_ops.queue_sgi = vgic_v3_queue_sgi;
> + dist->vm_ops.add_sgi_source = vgic_v3_add_sgi_source;
> + dist->vm_ops.vgic_init = vgic_v3_init;
> +
> + kvm->arch.max_vcpus = KVM_MAX_VCPUS;
> +
> + return 0;
> +}
> +
> +static int vgic_v3_create(struct kvm_device *dev, u32 type)
> +{
> + return kvm_vgic_create(dev->kvm, type);
> +}
> +
> +static void vgic_v3_destroy(struct kvm_device *dev)
> +{
> + kfree(dev);
> +}
> +
> +static int vgic_v3_set_attr(struct kvm_device *dev,
> + struct kvm_device_attr *attr)
> +{
> + int ret;
> +
> + ret = vgic_set_common_attr(dev, attr);
> + if (ret != -ENXIO)
> + return ret;
> +
> + switch (attr->group) {
> + case KVM_DEV_ARM_VGIC_GRP_DIST_REGS:
> + case KVM_DEV_ARM_VGIC_GRP_CPU_REGS:
> + return -ENXIO;
> + }
> +
> + return -ENXIO;
> +}
> +
> +static int vgic_v3_get_attr(struct kvm_device *dev,
> + struct kvm_device_attr *attr)
> +{
> + int ret;
> +
> + ret = vgic_get_common_attr(dev, attr);
> + if (ret != -ENXIO)
> + return ret;
> +
> + switch (attr->group) {
> + case KVM_DEV_ARM_VGIC_GRP_DIST_REGS:
> + case KVM_DEV_ARM_VGIC_GRP_CPU_REGS:
> + return -ENXIO;
> + }
> +
> + return -ENXIO;
> +}
> +
> +static int vgic_v3_has_attr(struct kvm_device *dev,
> + struct kvm_device_attr *attr)
> +{
> + switch (attr->group) {
> + case KVM_DEV_ARM_VGIC_GRP_ADDR:
> + switch (attr->attr) {
> + case KVM_VGIC_V2_ADDR_TYPE_DIST:
> + case KVM_VGIC_V2_ADDR_TYPE_CPU:
> + return -ENXIO;
> + }
> + break;
> + case KVM_DEV_ARM_VGIC_GRP_DIST_REGS:
> + case KVM_DEV_ARM_VGIC_GRP_CPU_REGS:
> + return -ENXIO;
> + case KVM_DEV_ARM_VGIC_GRP_NR_IRQS:
> + return 0;
> + }
> + return -ENXIO;
> +}
> +
> +struct kvm_device_ops kvm_arm_vgic_v3_ops = {
> + .name = "kvm-arm-vgic-v3",
> + .create = vgic_v3_create,
> + .destroy = vgic_v3_destroy,
> + .set_attr = vgic_v3_set_attr,
> + .get_attr = vgic_v3_get_attr,
> + .has_attr = vgic_v3_has_attr,
> +};
> diff --git a/virt/kvm/arm/vgic.c b/virt/kvm/arm/vgic.c
> index 335ffe0..b7de0f8 100644
> --- a/virt/kvm/arm/vgic.c
> +++ b/virt/kvm/arm/vgic.c
> @@ -1249,7 +1249,7 @@ static bool vgic_update_irq_pending(struct kvm *kvm, int cpuid,
> struct kvm_vcpu *vcpu;
> int edge_triggered, level_triggered;
> int enabled;
> - bool ret = true;
> + bool ret = true, can_inject = true;
>
> spin_lock(&dist->lock);
>
> @@ -1264,6 +1264,11 @@ static bool vgic_update_irq_pending(struct kvm *kvm, int cpuid,
>
> if (irq_num >= VGIC_NR_PRIVATE_IRQS) {
> cpuid = dist->irq_spi_cpu[irq_num - VGIC_NR_PRIVATE_IRQS];
> + if (cpuid == VCPU_NOT_ALLOCATED) {
> + /* Pretend we use CPU0, and prevent injection */
> + cpuid = 0;
> + can_inject = false;
> + }
> vcpu = kvm_get_vcpu(kvm, cpuid);
> }
>
> @@ -1285,7 +1290,7 @@ static bool vgic_update_irq_pending(struct kvm *kvm, int cpuid,
>
> enabled = vgic_irq_is_enabled(vcpu, irq_num);
>
> - if (!enabled) {
> + if (!enabled || !can_inject) {
> ret = false;
> goto out;
> }
> @@ -1438,6 +1443,7 @@ void kvm_vgic_destroy(struct kvm *kvm)
> }
> kfree(dist->irq_sgi_sources);
> kfree(dist->irq_spi_cpu);
> + kfree(dist->irq_spi_mpidr);
> kfree(dist->irq_spi_target);
> kfree(dist->irq_pending_on_cpu);
> dist->irq_sgi_sources = NULL;
> @@ -1628,6 +1634,7 @@ int kvm_vgic_create(struct kvm *kvm, u32 type)
> kvm->arch.vgic.vctrl_base = vgic->vctrl_base;
> kvm->arch.vgic.vgic_dist_base = VGIC_ADDR_UNDEF;
> kvm->arch.vgic.vgic_cpu_base = VGIC_ADDR_UNDEF;
> + kvm->arch.vgic.vgic_redist_base = VGIC_ADDR_UNDEF;
>
> out_unlock:
> for (; vcpu_lock_idx >= 0; vcpu_lock_idx--) {
> diff --git a/virt/kvm/arm/vgic.h b/virt/kvm/arm/vgic.h
> index ff3171a..b0c6b2f 100644
> --- a/virt/kvm/arm/vgic.h
> +++ b/virt/kvm/arm/vgic.h
> @@ -35,6 +35,8 @@
> #define ACCESS_WRITE_VALUE (3 << 1)
> #define ACCESS_WRITE_MASK(x) ((x) & (3 << 1))
>
> +#define VCPU_NOT_ALLOCATED ((u8)-1)
> +
> unsigned long *vgic_bitmap_get_shared_map(struct vgic_bitmap *x);
>
> void vgic_update_state(struct kvm *kvm);
> @@ -115,5 +117,6 @@ int vgic_set_common_attr(struct kvm_device *dev, struct kvm_device_attr *attr);
> int vgic_get_common_attr(struct kvm_device *dev, struct kvm_device_attr *attr);
>
> int vgic_v2_init_emulation(struct kvm *kvm);
> +int vgic_v3_init_emulation(struct kvm *kvm);
>
> #endif
> --
> 1.7.9.5
>
Thanks,
-Christoffer
More information about the linux-arm-kernel
mailing list