[PATCH v13 7/9] arm: sa1100: Migrate DEBUG_LL macros to shared directory

[Daniel Thompson]

As part of the migration we copy a few definitions from the mach-sa1100
headers and replace the automatic serial port detectiion with explicit
configuration based on DEBUG_UART_PHYS/DEBUG_UART_VIRT.

The removal of the automatic configuration is similar to the way migration
was handled for OMAP2 (see 808b7e07464d...).

Signed-off-by: Daniel Thompson <daniel.thompson at linaro.org>
Cc: Russell King <linux at arm.linux.org.uk>
---
 arch/arm/Kconfig.debug                             | 39 ++++++++++++++++++--
 .../mach/debug-macro.S => include/debug/sa1100.S}  | 41 +++++-----------------
 2 files changed, 45 insertions(+), 35 deletions(-)
 rename arch/arm/{mach-sa1100/include/mach/debug-macro.S => include/debug/sa1100.S} (39%)

diff --git a/arch/arm/Kconfig.debug b/arch/arm/Kconfig.debug
index 3e1a491f6f29..3070498fb637 100644
--- a/arch/arm/Kconfig.debug
+++ b/arch/arm/Kconfig.debug
@@ -785,6 +785,30 @@ choice
 		  their output to UART 2. The port must have been initialised
 		  by the boot-loader before use.
 
+	config DEBUG_SA1100_UART1
+		depends on ARCH_SA1100
+		select DEBUG_SA1100_UART
+		bool "Kernel low-level debugging messages via SA1100 Ser1"
+		help
+		  Say Y here if you want kernel low-level debugging support
+		  on SA1100 based platforms.
+
+	config DEBUG_SA1100_UART2
+		depends on ARCH_SA1100
+		select DEBUG_SA1100_UART
+		bool "Kernel low-level debugging messages via SA1100 Ser2"
+		help
+		  Say Y here if you want kernel low-level debugging support
+		  on SA1100 based platforms.
+
+	config DEBUG_SA1100_UART3
+		depends on ARCH_SA1100
+		select DEBUG_SA1100_UART
+		bool "Kernel low-level debugging messages via SA1100 Ser3"
+		help
+		  Say Y here if you want kernel low-level debugging support
+		  on SA1100 based platforms.
+
 	config DEBUG_SOCFPGA_UART
 		depends on ARCH_SOCFPGA
 		bool "Use SOCFPGA UART for low-level debug"
@@ -1088,6 +1112,10 @@ config DEBUG_TEGRA_UART
 	bool
 	depends on ARCH_TEGRA
 
+config DEBUG_SA1100_UART
+	bool
+	depends on ARCH_SA1100
+
 config DEBUG_STI_UART
 	bool
 	depends on ARCH_STI
@@ -1118,6 +1146,7 @@ config DEBUG_LL_INCLUDE
 	default "debug/omap2plus.S" if DEBUG_OMAP2PLUS_UART
 	default "debug/s3c24xx.S" if DEBUG_S3C24XX_UART
 	default "debug/s5pv210.S" if DEBUG_S5PV210_UART
+	default "debug/sa1100.S" if DEBUG_SA1100_UART
 	default "debug/sirf.S" if DEBUG_SIRFPRIMA2_UART1 || DEBUG_SIRFMARCO_UART1
 	default "debug/sti.S" if DEBUG_STI_UART
 	default "debug/tegra.S" if DEBUG_TEGRA_UART
@@ -1190,6 +1219,9 @@ config DEBUG_UART_PHYS
 				DEBUG_S3C2410_UART2)
 	default 0x78000000 if DEBUG_CNS3XXX
 	default 0x7c0003f8 if FOOTBRIDGE
+	default 0x80010000 if DEBUG_SA1100_UART1
+	default 0x80030000 if DEBUG_SA1100_UART2
+	default 0x80050000 if DEBUG_SA1100_UART3
 	default 0x80070000 if DEBUG_IMX23_UART
 	default 0x80074000 if DEBUG_IMX28_UART
 	default 0x80230000 if DEBUG_PICOXCELL_UART
@@ -1230,7 +1262,7 @@ config DEBUG_UART_PHYS
 		DEBUG_UART_8250 || DEBUG_UART_PL01X || DEBUG_MESON_UARTAO || \
 		DEBUG_MSM_UART || DEBUG_NETX_UART || \
 		DEBUG_QCOM_UARTDM || DEBUG_S3C24XX_UART || \
-		DEBUG_UART_BCM63XX
+		DEBUG_SA1100_UART || DEBUG_UART_BCM63XX
 
 config DEBUG_UART_VIRT
 	hex "Virtual base address of debug UART"
@@ -1259,6 +1291,9 @@ config DEBUG_UART_VIRT
 	default 0xf7fc9000 if DEBUG_BERLIN_UART
 	default 0xf8007000 if DEBUG_HIP04_UART
 	default 0xf8009000 if DEBUG_VEXPRESS_UART0_CA9
+	default 0xf8010000 if DEBUG_SA1100_UART1
+	default 0xf8030000 if DEBUG_SA1100_UART2
+	default 0xf8050000 if DEBUG_SA1100_UART3
 	default 0xf8090000 if DEBUG_VEXPRESS_UART0_RS1
 	default 0xfa71e000 if DEBUG_QCOM_UARTDM
 	default 0xfb002000 if DEBUG_CNS3XXX
@@ -1308,7 +1343,7 @@ config DEBUG_UART_VIRT
 		DEBUG_UART_8250 || DEBUG_UART_PL01X || DEBUG_MESON_UARTAO || \
 		DEBUG_MSM_UART || DEBUG_NETX_UART || \
 		DEBUG_QCOM_UARTDM || DEBUG_S3C24XX_UART || \
-		DEBUG_UART_BCM63XX
+		DEBUG_SA1100_UART || DEBUG_UART_BCM63XX
 
 config DEBUG_UART_8250_SHIFT
 	int "Register offset shift for the 8250 debug UART"
diff --git a/arch/arm/mach-sa1100/include/mach/debug-macro.S b/arch/arm/include/debug/sa1100.S
similarity index 39%
rename from arch/arm/mach-sa1100/include/mach/debug-macro.S
rename to arch/arm/include/debug/sa1100.S
index 530772d937ad..6b5e1ce099d3 100644
--- a/arch/arm/mach-sa1100/include/mach/debug-macro.S
+++ b/arch/arm/include/debug/sa1100.S
@@ -1,5 +1,4 @@
-/* arch/arm/mach-sa1100/include/mach/debug-macro.S
- *
+/*
  * Debugging macro include header
  *
  *  Copyright (C) 1994-1999 Russell King
@@ -10,39 +9,15 @@
  * published by the Free Software Foundation.
  *
 */
-#include <mach/hardware.h>
-
-		.macro	addruart, rp, rv, tmp
-		mrc	p15, 0, \rp, c1, c0
-		tst	\rp, #1			@ MMU enabled?
-		moveq	\rp, #0x80000000	@ physical base address
-		movne	\rp, #0xf8000000	@ virtual address
-
-		@ We probe for the active serial port here, coherently with
-		@ the comment in arch/arm/mach-sa1100/include/mach/uncompress.h.
-		@ We assume r1 can be clobbered.
 
-		@ see if Ser3 is active
-		add	\rp, \rp, #0x00050000
-		ldr	\rv, [\rp, #UTCR3]
-		tst	\rv, #UTCR3_TXE
-
-		@ if Ser3 is inactive, then try Ser1
-		addeq	\rp, \rp, #(0x00010000 - 0x00050000)
-		ldreq	\rv, [\rp, #UTCR3]
-		tsteq	\rv, #UTCR3_TXE
-
-		@ if Ser1 is inactive, then try Ser2
-		addeq	\rp, \rp, #(0x00030000 - 0x00010000)
-		ldreq	\rv, [\rp, #UTCR3]
-		tsteq	\rv, #UTCR3_TXE
-
-		@ clear top bits, and generate both phys and virt addresses
-		lsl	\rp, \rp, #8
-		lsr	\rp, \rp, #8
-		orr	\rv, \rp, #0xf8000000	@ virtual
-		orr	\rp, \rp, #0x80000000	@ physical
+#define UTDR            0x14
+#define UTSR1           0x20
+#define UTSR1_TBY       0x00000001      /* Transmitter BusY (read)         */
+#define UTSR1_TNF       0x00000004      /* Transmit FIFO Not Full (read)   */
 
+		.macro	addruart, rp, rv, tmp
+		ldr	\rp, =CONFIG_DEBUG_UART_PHYS
+		ldr	\rv, =CONFIG_DEBUG_UART_VIRT
 		.endm
 
 		.macro	senduart,rd,rx
-- 
1.9.3