[PATCH 4/4] arm: dts: omap3-gta04: Add static configuration for devconf1 register

[Grazvydas Ignotas]

On Fri, Nov 14, 2014 at 1:58 AM, Tony Lindgren <tony at atomide.com> wrote:
> * Paul Walmsley <paul at pwsan.com> [141113 15:01]:
>> Hi
>>
>> On Thu, 13 Nov 2014, Tony Lindgren wrote:
>>
>> > * Tomi Valkeinen <tomi.valkeinen at ti.com> [141113 03:33]:
>> > > On 12/11/14 17:02, Tony Lindgren wrote:
>> > >
>> > > >> And, with a quick grep, I see CONTROL_DEVCONF1 touched in multiple
>> > > >> places in the kernel. I wonder if adding a pinmux entry for it could
>> > > >> cause some rather odd problems.
>> > > >
>> > > > They can all use pinctrl-single no problem.
>> > >
>> > > Can, but don't. That's my worry. If we touch the DEVCONF1 via pinmux,
>> > > and we have code in mach-omap2 that also touch DEVCONF1, without any
>> > > knowledge (and locking) between those...
>> >
>> > Hmm yeah the McBSP clock mux could be racy as the mux register for
>> > McBSP is treated as a clock. This register muxes the clock between
>> > external pin and internal clock. Considering that this should be
>> > selectable at board level as the external clock probably needs to be
>> > used if level shifters are being used, it should be really handled by
>> > pinctrl-single.
>> >
>> > The other use for hsmmc.c and pdata-quirks.c for the one time mux for
>> > MMC clock from the MMC clock pin. That can be done with pinctrl-single
>> > from the MMC driver too for DT based booting.
>> >
>> > Then we just have the save and restore of the registers for
>> > off-idle.
>> >
>> > > So _maybe_ that's not an issue, as the pinmux config we have here is
>> > > fixed, and done once at boot time, and maybe the code in mach-omap2 that
>> > > touch DEVCONF1 is also ran just once and not at the same time as the
>> > > pinmux. But I don't know if that's so.
>> >
>> > It seems we could just do a read-only check for McBSP in the clock
>> > code for the mux register, or even completely drop that code from
>> > cclock3xxx_data.c and start using the pinctrl for that mux.
>> >
>> > Paul & Tero, got any comments here?
>>
>> It's best to move all of the SCM register reads/writes to an SCM IP block
>> driver.  This driver would be the only entity that would touch the SCM IP
>> block registers - no other code on the system would touch it (perhaps
>> aside from anything needed for early init).  The SCM driver would enforce
>> mutual exclusion via a spinlock, so concurrent SCM register modifications
>> wouldn't flake out.  Then the SCM driver would register clocks with the
>> CCF, register pins with the pinctrl subsystem, etc. etc.
>
> We actually do have that with pinctrl-single + syscon. We certainly
> need to implement more Linux framework drivers for the SCM registers.
> Things like regulators, clocks, and PHYs, but they should use
> pinctrl-single + syscon. See the the pbias-regulator.c for example.
>
> Looking at the McBSP clock handling, threre's yet more handling of
> the same DEVCONF1 mux register in omap2_mcbsp_set_clks_src that gets
> alled from omap_mcbsp_dai_set_dai_sysclk.
>
> To me it seems that if we handle the DEVCONF with pinctrl-single, we
> don't need most of the McBSP fck code or the omap2_mcbsp_set_clks_src.
> Having the mux register as the clock enable register is not nice..
> Who knows what the clock coming from the external pin might be :)

How will audio do dynamic muxing without that code?
The pin must be remuxed back to internal clock when audio stops, or
else PM breaks.


Gražvydas