[PATCH v8 4/8] ARM: dts: Enable Broadcom Cygnus SoC
Scott Branden
sbranden at broadcom.com
Sat Nov 8 22:13:04 PST 2014
On 14-11-08 04:22 PM, Olof Johansson wrote:
> Hi,
>
> A bunch of small comments below, should be quick to fix.
>
> On Tue, Oct 28, 2014 at 12:53 PM, Scott Branden <sbranden at broadcom.com> wrote:
>> DT files to enable cygnus consisting on reference designs
>> and cygnus core configuration.
>>
>> Reviewed-by: Ray Jui <rjui at broadcom.com>
>> Reviewed-by: Arun Parameswaran <aparames at broadcom.com>
>> Tested-by: Jonathan Richardson <jonathar at broadcom.com>
>> Reviewed-by: JD (Jiandong) Zheng <jdzheng at broadcom.com>
>> Signed-off-by: Scott Branden <sbranden at broadcom.com>
>> ---
>> arch/arm/boot/dts/Makefile | 4 ++
>> arch/arm/boot/dts/bcm-cygnus-clock.dtsi | 73 ++++++++++++++++++++++
>> arch/arm/boot/dts/bcm-cygnus.dtsi | 100 +++++++++++++++++++++++++++++++
>> arch/arm/boot/dts/bcm911360_entphn.dts | 32 ++++++++++
>> arch/arm/boot/dts/bcm911360k.dts | 32 ++++++++++
>> arch/arm/boot/dts/bcm958300k.dts | 32 ++++++++++
>> 6 files changed, 273 insertions(+)
>> create mode 100644 arch/arm/boot/dts/bcm-cygnus-clock.dtsi
>> create mode 100644 arch/arm/boot/dts/bcm-cygnus.dtsi
>> create mode 100644 arch/arm/boot/dts/bcm911360_entphn.dts
>> create mode 100644 arch/arm/boot/dts/bcm911360k.dts
>> create mode 100644 arch/arm/boot/dts/bcm958300k.dts
>>
>> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
>> index 38c89ca..4b3a590 100644
>> --- a/arch/arm/boot/dts/Makefile
>> +++ b/arch/arm/boot/dts/Makefile
>> @@ -54,6 +54,10 @@ dtb-$(CONFIG_ARCH_AT91) += at91-sama5d4ek.dtb
>> dtb-$(CONFIG_ARCH_ATLAS6) += atlas6-evb.dtb
>> dtb-$(CONFIG_ARCH_AXXIA) += axm5516-amarillo.dtb
>> dtb-$(CONFIG_ARCH_BCM2835) += bcm2835-rpi-b.dtb
>> +dtb-$(CONFIG_ARCH_BCM_CYGNUS) += \
>> + bcm911360_entphn.dtb \
>> + bcm911360k.dtb \
>> + bcm958300k.dtb
>> dtb-$(CONFIG_ARCH_BCM_5301X) += bcm4708-netgear-r6250.dtb
>> dtb-$(CONFIG_ARCH_BCM_63XX) += bcm963138dvt.dtb
>> dtb-$(CONFIG_ARCH_BCM_MOBILE) += bcm28155-ap.dtb \
>
> Please add new entries in alphabetical/alphanumerical order. Also,
> first entry is commonly added on the first line
>
>
>> diff --git a/arch/arm/boot/dts/bcm-cygnus-clock.dtsi b/arch/arm/boot/dts/bcm-cygnus-clock.dtsi
>> new file mode 100644
>> index 0000000..d06172b
>> --- /dev/null
>> +++ b/arch/arm/boot/dts/bcm-cygnus-clock.dtsi
>> @@ -0,0 +1,73 @@
>> +/*
>> + * Copyright 2014 Broadcom Corporation. All rights reserved.
>> + *
>> + * Unless you and Broadcom execute a separate written software license
>> + * agreement governing use of this software, this software is licensed to you
>> + * under the terms of the GNU General Public License as
>> + * published by the Free Software Foundation version 2.
>> + *
>> + * This program is distributed "as is" WITHOUT ANY WARRANTY of any
>> + * kind, whether express or implied; without even the implied warranty
>> + * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
>> + * GNU General Public License for more details.
>
> We ask for new DT contents to be added with dual BSD/GPL license, to
> allow for reuse of the DT data structures in other projects as well.
> There's currently a lot of activity going on relicensing the current
> files so I recommend sorting it out before they are added if you can.
This may take more time than you think. I am going to have to go
through legal to get such a license created. Also, why would you need
dual license? If it is BSD that should serve both purposes?
>
>> + */
>> +
>> +clocks {
>> + #address-cells = <1>;
>> + #size-cells = <1>;
>> + ranges;
>> +
>> + osc: oscillator {
>> + compatible = "fixed-clock";
>> + #clock-cells = <1>;
>> + clock-frequency = <25000000>;
>> + };
>> +
>> + apb_clk: apb_clk {
>> + compatible = "fixed-clock";
>> + #clock-cells = <0>;
>> + clock-frequency = <1000000000>;
>> + };
>> +
>> + periph_clk: periph_clk {
>> + compatible = "fixed-clock";
>> + #clock-cells = <0>;
>> + clock-frequency = <500000000>;
>> + };
>> +
>> + sdio_clk: lcpll_ch2 {
>> + compatible = "fixed-clock";
>> + #clock-cells = <0>;
>> + clock-frequency = <200000000>;
>> + };
>> +
>> + axi81_clk: axi81_clk {
>> + compatible = "fixed-clock";
>> + #clock-cells = <0>;
>> + clock-frequency = <100000000>;
>> + };
>> +
>> + keypad_clk: keypad_clk {
>> + compatible = "fixed-clock";
>> + #clock-cells = <0>;
>> + clock-frequency = <31806>;
>> + };
>> +
>> + adc_clk: adc_clk {
>> + compatible = "fixed-clock";
>> + #clock-cells = <0>;
>> + clock-frequency = <1562500>;
>> + };
>> +
>> + pwm_clk: pwm_clk {
>> + compatible = "fixed-clock";
>> + #clock-cells = <0>;
>> + clock-frequency = <1000000>;
>> + };
>> +
>> + lcd_clk: mipipll_ch1 {
>> + compatible = "fixed-clock";
>> + #clock-cells = <0>;
>> + clock-frequency = <100000000>;
>> + };
>> +};
>> diff --git a/arch/arm/boot/dts/bcm-cygnus.dtsi b/arch/arm/boot/dts/bcm-cygnus.dtsi
>> new file mode 100644
>> index 0000000..9c650ab
>> --- /dev/null
>> +++ b/arch/arm/boot/dts/bcm-cygnus.dtsi
>> @@ -0,0 +1,100 @@
>> +/*
>> + * Copyright 2014 Broadcom Corporation. All rights reserved.
>> + *
>> + * Unless you and Broadcom execute a separate written software license
>> + * agreement governing use of this software, this software is licensed to you
>> + * under the terms of the GNU General Public License as
>> + * published by the Free Software Foundation version 2.
>> + *
>> + * This program is distributed "as is" WITHOUT ANY WARRANTY of any
>> + * kind, whether express or implied; without even the implied warranty
>> + * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
>> + * GNU General Public License for more details.
>> + */
>> +
>> +#include <dt-bindings/interrupt-controller/arm-gic.h>
>> +#include <dt-bindings/interrupt-controller/irq.h>
>> +
>> +#include "skeleton.dtsi"
>> +
>> +/ {
>> + compatible = "brcm,cygnus";
>> + model = "Broadcom Cygnus SoC";
>> + interrupt-parent = <&gic>;
>> +
>> + cpus {
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> +
>> + cpu at 0 {
>> + device_type = "cpu";
>> + compatible = "arm,cortex-a9";
>> + next-level-cache = <&L2>;
>> + reg = <0x0>;
>> + };
>> + };
>> +
>> + /include/ "bcm-cygnus-clock.dtsi"
>> +
>> + amba {
>> + #address-cells = <1>;
>> + #size-cells = <1>;
>> + compatible = "arm,amba-bus", "simple-bus";
>> + interrupt-parent = <&gic>;
>> + ranges;
>> +
>> + wdt at 18009000 {
>> + compatible = "arm,sp805" , "arm,primecell";
>> + reg = <0x18009000 0x1000>;
>> + interrupts = <GIC_SPI 91 IRQ_TYPE_LEVEL_HIGH>;
>> + clocks = <&axi81_clk>;
>> + clock-names = "apb_pclk";
>> + };
>> + };
>> +
>> + uart3: serial at 18023000 {
>> + compatible = "snps,dw-apb-uart";
>> + reg = <0x18023000 0x100>;
>> + reg-shift = <2>;
>> + reg-io-width = <4>;
>> + interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>;
>> + clock-frequency = <100000000>;
>> + clocks = <&axi81_clk>;
>> + status = "okay";
>
> It is common to leave these disabled in the SoC/common dtsi, and
> enable them in the per-board dts files, since different boards might
> not use all peripherals, etc.
>
> It seems like all your boards currently use both uarts, but if it
> changes in the future please consider switching over. It might be
> worth doing so now to avoid churn later on. That also allows you to
> define all the uards (I'm going to guess that there's a total of at
> least 4 on this system :).
>
>> + };
>> +
>> + uart0: serial at 18020000 {
>
> These are also out of order, uart3 is before uart0 (and the registers
> are in reverse order).
>
> We normally recommend that you add entries sorted by reg/unit address
> -- that way there's less risk of conflict due to add/add compared to
> if people just append new entries at the end of the file.
>
>> + compatible = "snps,dw-apb-uart";
>> + reg = <0x18020000 0x100>;
>> + reg-shift = <2>;
>> + reg-io-width = <4>;
>> + interrupts = <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>;
>> + clocks = <&axi81_clk>;
>> + clock-frequency = <100000000>;
>> + status = "okay";
>> + };
>> +
>> + gic: interrupt-controller at 19021000 {
>> + compatible = "arm,cortex-a9-gic";
>> + #interrupt-cells = <3>;
>> + #address-cells = <0>;
>> + interrupt-controller;
>> + reg = <0x19021000 0x1000>,
>> + <0x19020100 0x100>;
>> + };
>> +
>> + L2: l2-cache {
>
> l2-cache at 19022000
>
>> + compatible = "arm,pl310-cache";
>> + reg = <0x19022000 0x1000>;
>> + cache-unified;
>> + cache-level = <2>;
>> + };
>> +
>> + timer at 19020200 {
>> + compatible = "arm,cortex-a9-global-timer";
>> + reg = <0x19020200 0x100>;
>> + interrupts = <GIC_PPI 11 IRQ_TYPE_LEVEL_HIGH>;
>> + clocks = <&periph_clk>;
>> + };
>> +
>> +};
>> diff --git a/arch/arm/boot/dts/bcm911360_entphn.dts b/arch/arm/boot/dts/bcm911360_entphn.dts
>> new file mode 100644
>> index 0000000..9de5e87
>> --- /dev/null
>> +++ b/arch/arm/boot/dts/bcm911360_entphn.dts
>> @@ -0,0 +1,32 @@
>> +/*
>> + * Copyright 2014 Broadcom Corporation. All rights reserved.
>> + *
>> + * Unless you and Broadcom execute a separate written software license
>> + * agreement governing use of this software, this software is licensed to you
>> + * under the terms of the GNU General Public License as
>> + * published by the Free Software Foundation version 2.
>> + *
>> + * This program is distributed "as is" WITHOUT ANY WARRANTY of any
>> + * kind, whether express or implied; without even the implied warranty
>> + * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
>> + * GNU General Public License for more details.
>> + */
>> +
>> +/dts-v1/;
>> +
>> +#include "bcm-cygnus.dtsi"
>> +
>> +/ {
>> + model = "Cygnus Enterprise Phone (BCM911360_ENTPHN)";
>> + compatible = "brcm,bcm11360", "brcm,cygnus";
>> +
>> + aliases {
>> + serial0 = &uart3;
>> + serial1 = &uart0;
>> + };
>> +
>> + chosen {
>> + stdout-path = &uart3;
>> + bootargs = "console=ttyS0,115200";
>> + };
>> +};
>> diff --git a/arch/arm/boot/dts/bcm911360k.dts b/arch/arm/boot/dts/bcm911360k.dts
>> new file mode 100644
>> index 0000000..dd4f102
>> --- /dev/null
>> +++ b/arch/arm/boot/dts/bcm911360k.dts
>> @@ -0,0 +1,32 @@
>> +/*
>> + * Copyright 2014 Broadcom Corporation. All rights reserved.
>> + *
>> + * Unless you and Broadcom execute a separate written software license
>> + * agreement governing use of this software, this software is licensed to you
>> + * under the terms of the GNU General Public License as
>> + * published by the Free Software Foundation version 2.
>> + *
>> + * This program is distributed "as is" WITHOUT ANY WARRANTY of any
>> + * kind, whether express or implied; without even the implied warranty
>> + * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
>> + * GNU General Public License for more details.
>> + */
>> +
>> +/dts-v1/;
>> +
>> +#include "bcm-cygnus.dtsi"
>> +
>> +/ {
>> + model = "Cygnus SVK (BCM911360K)";
>> + compatible = "brcm,bcm11360", "brcm,cygnus";
>> +
>> + aliases {
>> + serial0 = &uart3;
>> + serial1 = &uart0;
>> + };
>> +
>> + chosen {
>> + stdout-path = &uart3;
>> + bootargs = "console=ttyS0,115200";
>> + };
>> +};
>> diff --git a/arch/arm/boot/dts/bcm958300k.dts b/arch/arm/boot/dts/bcm958300k.dts
>> new file mode 100644
>> index 0000000..f8b9625
>> --- /dev/null
>> +++ b/arch/arm/boot/dts/bcm958300k.dts
>> @@ -0,0 +1,32 @@
>> +/*
>> + * Copyright 2014 Broadcom Corporation. All rights reserved.
>> + *
>> + * Unless you and Broadcom execute a separate written software license
>> + * agreement governing use of this software, this software is licensed to you
>> + * under the terms of the GNU General Public License as
>> + * published by the Free Software Foundation version 2.
>> + *
>> + * This program is distributed "as is" WITHOUT ANY WARRANTY of any
>> + * kind, whether express or implied; without even the implied warranty
>> + * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
>> + * GNU General Public License for more details.
>> + */
>> +
>> +/dts-v1/;
>> +
>> +#include "bcm-cygnus.dtsi"
>> +
>> +/ {
>> + model = "Cygnus SVK (BCM958300K)";
>> + compatible = "brcm,bcm58300", "brcm,cygnus";
>> +
>> + aliases {
>> + serial0 = &uart3;
>> + serial1 = &uart0;
>> + };
>> +
>> + chosen {
>> + stdout-path = &uart3;
>> + bootargs = "console=ttyS0,115200";
>> + };
>> +};
>> --
>> 1.7.9.5
>>
>>
>> _______________________________________________
>> linux-arm-kernel mailing list
>> linux-arm-kernel at lists.infradead.org
>> http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
More information about the linux-arm-kernel
mailing list