[PATCH] ARM: at91: move sdramc/ddrsdr header to include/soc/at91
Alexandre Belloni
alexandre.belloni at free-electrons.com
Fri Nov 7 12:58:21 PST 2014
Move the (DDR) SDRAM controller headers to include/soc/at91 to remove the
dependency on mach/ headers from the at91-reset driver.
Signed-off-by: Alexandre Belloni <alexandre.belloni at free-electrons.com>
---
As my previous attempts were not popular, solve the mach/ headers issue by
simply moving them. I'll get back to better driver separation when it will be
possible to map the SRAM as executable memory.
MAINTAINERS | 1 +
arch/arm/mach-at91/include/mach/at91_ramc.h | 6 +-
.../arm/mach-at91/include/mach/at91rm9200_sdramc.h | 63 -----------
arch/arm/mach-at91/include/mach/at91sam9_ddrsdr.h | 124 ---------------------
arch/arm/mach-at91/include/mach/at91sam9_sdramc.h | 85 --------------
arch/arm/mach-at91/pm.h | 1 -
drivers/power/reset/at91-reset.c | 4 +-
include/soc/at91/at91rm9200_sdramc.h | 63 +++++++++++
include/soc/at91/at91sam9_ddrsdr.h | 124 +++++++++++++++++++++
include/soc/at91/at91sam9_sdramc.h | 85 ++++++++++++++
10 files changed, 278 insertions(+), 278 deletions(-)
delete mode 100644 arch/arm/mach-at91/include/mach/at91rm9200_sdramc.h
delete mode 100644 arch/arm/mach-at91/include/mach/at91sam9_ddrsdr.h
delete mode 100644 arch/arm/mach-at91/include/mach/at91sam9_sdramc.h
create mode 100644 include/soc/at91/at91rm9200_sdramc.h
create mode 100644 include/soc/at91/at91sam9_ddrsdr.h
create mode 100644 include/soc/at91/at91sam9_sdramc.h
diff --git a/MAINTAINERS b/MAINTAINERS
index 3c6427190be2..e8f5474ce9b4 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -861,6 +861,7 @@ W: http://maxim.org.za/at91_26.html
W: http://www.linux4sam.org
S: Supported
F: arch/arm/mach-at91/
+F: include/soc/at91/
F: arch/arm/boot/dts/at91*.dts
F: arch/arm/boot/dts/at91*.dtsi
F: arch/arm/boot/dts/sama*.dts
diff --git a/arch/arm/mach-at91/include/mach/at91_ramc.h b/arch/arm/mach-at91/include/mach/at91_ramc.h
index d8aeb278614e..e4492b151fee 100644
--- a/arch/arm/mach-at91/include/mach/at91_ramc.h
+++ b/arch/arm/mach-at91/include/mach/at91_ramc.h
@@ -25,8 +25,8 @@ extern void __iomem *at91_ramc_base[];
#define AT91_MEMCTRL_SDRAMC 1
#define AT91_MEMCTRL_DDRSDR 2
-#include <mach/at91rm9200_sdramc.h>
-#include <mach/at91sam9_ddrsdr.h>
-#include <mach/at91sam9_sdramc.h>
+#include <soc/at91/at91rm9200_sdramc.h>
+#include <soc/at91/at91sam9_ddrsdr.h>
+#include <soc/at91/at91sam9_sdramc.h>
#endif /* __AT91_RAMC_H__ */
diff --git a/arch/arm/mach-at91/include/mach/at91rm9200_sdramc.h b/arch/arm/mach-at91/include/mach/at91rm9200_sdramc.h
deleted file mode 100644
index aa047f458f1b..000000000000
--- a/arch/arm/mach-at91/include/mach/at91rm9200_sdramc.h
+++ /dev/null
@@ -1,63 +0,0 @@
-/*
- * arch/arm/mach-at91/include/mach/at91rm9200_sdramc.h
- *
- * Copyright (C) 2005 Ivan Kokshaysky
- * Copyright (C) SAN People
- *
- * Memory Controllers (SDRAMC only) - System peripherals registers.
- * Based on AT91RM9200 datasheet revision E.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- */
-
-#ifndef AT91RM9200_SDRAMC_H
-#define AT91RM9200_SDRAMC_H
-
-/* SDRAM Controller registers */
-#define AT91RM9200_SDRAMC_MR 0x90 /* Mode Register */
-#define AT91RM9200_SDRAMC_MODE (0xf << 0) /* Command Mode */
-#define AT91RM9200_SDRAMC_MODE_NORMAL (0 << 0)
-#define AT91RM9200_SDRAMC_MODE_NOP (1 << 0)
-#define AT91RM9200_SDRAMC_MODE_PRECHARGE (2 << 0)
-#define AT91RM9200_SDRAMC_MODE_LMR (3 << 0)
-#define AT91RM9200_SDRAMC_MODE_REFRESH (4 << 0)
-#define AT91RM9200_SDRAMC_DBW (1 << 4) /* Data Bus Width */
-#define AT91RM9200_SDRAMC_DBW_32 (0 << 4)
-#define AT91RM9200_SDRAMC_DBW_16 (1 << 4)
-
-#define AT91RM9200_SDRAMC_TR 0x94 /* Refresh Timer Register */
-#define AT91RM9200_SDRAMC_COUNT (0xfff << 0) /* Refresh Timer Count */
-
-#define AT91RM9200_SDRAMC_CR 0x98 /* Configuration Register */
-#define AT91RM9200_SDRAMC_NC (3 << 0) /* Number of Column Bits */
-#define AT91RM9200_SDRAMC_NC_8 (0 << 0)
-#define AT91RM9200_SDRAMC_NC_9 (1 << 0)
-#define AT91RM9200_SDRAMC_NC_10 (2 << 0)
-#define AT91RM9200_SDRAMC_NC_11 (3 << 0)
-#define AT91RM9200_SDRAMC_NR (3 << 2) /* Number of Row Bits */
-#define AT91RM9200_SDRAMC_NR_11 (0 << 2)
-#define AT91RM9200_SDRAMC_NR_12 (1 << 2)
-#define AT91RM9200_SDRAMC_NR_13 (2 << 2)
-#define AT91RM9200_SDRAMC_NB (1 << 4) /* Number of Banks */
-#define AT91RM9200_SDRAMC_NB_2 (0 << 4)
-#define AT91RM9200_SDRAMC_NB_4 (1 << 4)
-#define AT91RM9200_SDRAMC_CAS (3 << 5) /* CAS Latency */
-#define AT91RM9200_SDRAMC_CAS_2 (2 << 5)
-#define AT91RM9200_SDRAMC_TWR (0xf << 7) /* Write Recovery Delay */
-#define AT91RM9200_SDRAMC_TRC (0xf << 11) /* Row Cycle Delay */
-#define AT91RM9200_SDRAMC_TRP (0xf << 15) /* Row Precharge Delay */
-#define AT91RM9200_SDRAMC_TRCD (0xf << 19) /* Row to Column Delay */
-#define AT91RM9200_SDRAMC_TRAS (0xf << 23) /* Active to Precharge Delay */
-#define AT91RM9200_SDRAMC_TXSR (0xf << 27) /* Exit Self Refresh to Active Delay */
-
-#define AT91RM9200_SDRAMC_SRR 0x9c /* Self Refresh Register */
-#define AT91RM9200_SDRAMC_LPR 0xa0 /* Low Power Register */
-#define AT91RM9200_SDRAMC_IER 0xa4 /* Interrupt Enable Register */
-#define AT91RM9200_SDRAMC_IDR 0xa8 /* Interrupt Disable Register */
-#define AT91RM9200_SDRAMC_IMR 0xac /* Interrupt Mask Register */
-#define AT91RM9200_SDRAMC_ISR 0xb0 /* Interrupt Status Register */
-
-#endif
diff --git a/arch/arm/mach-at91/include/mach/at91sam9_ddrsdr.h b/arch/arm/mach-at91/include/mach/at91sam9_ddrsdr.h
deleted file mode 100644
index 0210797abf2e..000000000000
--- a/arch/arm/mach-at91/include/mach/at91sam9_ddrsdr.h
+++ /dev/null
@@ -1,124 +0,0 @@
-/*
- * Header file for the Atmel DDR/SDR SDRAM Controller
- *
- * Copyright (C) 2010 Atmel Corporation
- * Nicolas Ferre <nicolas.ferre at atmel.com>
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- */
-#ifndef AT91SAM9_DDRSDR_H
-#define AT91SAM9_DDRSDR_H
-
-#define AT91_DDRSDRC_MR 0x00 /* Mode Register */
-#define AT91_DDRSDRC_MODE (0x7 << 0) /* Command Mode */
-#define AT91_DDRSDRC_MODE_NORMAL 0
-#define AT91_DDRSDRC_MODE_NOP 1
-#define AT91_DDRSDRC_MODE_PRECHARGE 2
-#define AT91_DDRSDRC_MODE_LMR 3
-#define AT91_DDRSDRC_MODE_REFRESH 4
-#define AT91_DDRSDRC_MODE_EXT_LMR 5
-#define AT91_DDRSDRC_MODE_DEEP 6
-
-#define AT91_DDRSDRC_RTR 0x04 /* Refresh Timer Register */
-#define AT91_DDRSDRC_COUNT (0xfff << 0) /* Refresh Timer Counter */
-
-#define AT91_DDRSDRC_CR 0x08 /* Configuration Register */
-#define AT91_DDRSDRC_NC (3 << 0) /* Number of Column Bits */
-#define AT91_DDRSDRC_NC_SDR8 (0 << 0)
-#define AT91_DDRSDRC_NC_SDR9 (1 << 0)
-#define AT91_DDRSDRC_NC_SDR10 (2 << 0)
-#define AT91_DDRSDRC_NC_SDR11 (3 << 0)
-#define AT91_DDRSDRC_NC_DDR9 (0 << 0)
-#define AT91_DDRSDRC_NC_DDR10 (1 << 0)
-#define AT91_DDRSDRC_NC_DDR11 (2 << 0)
-#define AT91_DDRSDRC_NC_DDR12 (3 << 0)
-#define AT91_DDRSDRC_NR (3 << 2) /* Number of Row Bits */
-#define AT91_DDRSDRC_NR_11 (0 << 2)
-#define AT91_DDRSDRC_NR_12 (1 << 2)
-#define AT91_DDRSDRC_NR_13 (2 << 2)
-#define AT91_DDRSDRC_NR_14 (3 << 2)
-#define AT91_DDRSDRC_CAS (7 << 4) /* CAS Latency */
-#define AT91_DDRSDRC_CAS_2 (2 << 4)
-#define AT91_DDRSDRC_CAS_3 (3 << 4)
-#define AT91_DDRSDRC_CAS_25 (6 << 4)
-#define AT91_DDRSDRC_RST_DLL (1 << 7) /* Reset DLL */
-#define AT91_DDRSDRC_DICDS (1 << 8) /* Output impedance control */
-#define AT91_DDRSDRC_DIS_DLL (1 << 9) /* Disable DLL [SAM9 Only] */
-#define AT91_DDRSDRC_OCD (1 << 12) /* Off-Chip Driver [SAM9 Only] */
-#define AT91_DDRSDRC_DQMS (1 << 16) /* Mask Data is Shared [SAM9 Only] */
-#define AT91_DDRSDRC_ACTBST (1 << 18) /* Active Bank X to Burst Stop Read Access Bank Y [SAM9 Only] */
-
-#define AT91_DDRSDRC_T0PR 0x0C /* Timing 0 Register */
-#define AT91_DDRSDRC_TRAS (0xf << 0) /* Active to Precharge delay */
-#define AT91_DDRSDRC_TRCD (0xf << 4) /* Row to Column delay */
-#define AT91_DDRSDRC_TWR (0xf << 8) /* Write recovery delay */
-#define AT91_DDRSDRC_TRC (0xf << 12) /* Row cycle delay */
-#define AT91_DDRSDRC_TRP (0xf << 16) /* Row precharge delay */
-#define AT91_DDRSDRC_TRRD (0xf << 20) /* Active BankA to BankB */
-#define AT91_DDRSDRC_TWTR (0x7 << 24) /* Internal Write to Read delay */
-#define AT91_DDRSDRC_RED_WRRD (0x1 << 27) /* Reduce Write to Read Delay [SAM9 Only] */
-#define AT91_DDRSDRC_TMRD (0xf << 28) /* Load mode to active/refresh delay */
-
-#define AT91_DDRSDRC_T1PR 0x10 /* Timing 1 Register */
-#define AT91_DDRSDRC_TRFC (0x1f << 0) /* Row Cycle Delay */
-#define AT91_DDRSDRC_TXSNR (0xff << 8) /* Exit self-refresh to non-read */
-#define AT91_DDRSDRC_TXSRD (0xff << 16) /* Exit self-refresh to read */
-#define AT91_DDRSDRC_TXP (0xf << 24) /* Exit power-down delay */
-
-#define AT91_DDRSDRC_T2PR 0x14 /* Timing 2 Register [SAM9 Only] */
-#define AT91_DDRSDRC_TXARD (0xf << 0) /* Exit active power down delay to read command in mode "Fast Exit" */
-#define AT91_DDRSDRC_TXARDS (0xf << 4) /* Exit active power down delay to read command in mode "Slow Exit" */
-#define AT91_DDRSDRC_TRPA (0xf << 8) /* Row Precharge All delay */
-#define AT91_DDRSDRC_TRTP (0x7 << 12) /* Read to Precharge delay */
-
-#define AT91_DDRSDRC_LPR 0x1C /* Low Power Register */
-#define AT91_DDRSDRC_LPCB (3 << 0) /* Low-power Configurations */
-#define AT91_DDRSDRC_LPCB_DISABLE 0
-#define AT91_DDRSDRC_LPCB_SELF_REFRESH 1
-#define AT91_DDRSDRC_LPCB_POWER_DOWN 2
-#define AT91_DDRSDRC_LPCB_DEEP_POWER_DOWN 3
-#define AT91_DDRSDRC_CLKFR (1 << 2) /* Clock Frozen */
-#define AT91_DDRSDRC_PASR (7 << 4) /* Partial Array Self Refresh */
-#define AT91_DDRSDRC_TCSR (3 << 8) /* Temperature Compensated Self Refresh */
-#define AT91_DDRSDRC_DS (3 << 10) /* Drive Strength */
-#define AT91_DDRSDRC_TIMEOUT (3 << 12) /* Time to define when Low Power Mode is enabled */
-#define AT91_DDRSDRC_TIMEOUT_0_CLK_CYCLES (0 << 12)
-#define AT91_DDRSDRC_TIMEOUT_64_CLK_CYCLES (1 << 12)
-#define AT91_DDRSDRC_TIMEOUT_128_CLK_CYCLES (2 << 12)
-#define AT91_DDRSDRC_APDE (1 << 16) /* Active power down exit time */
-#define AT91_DDRSDRC_UPD_MR (3 << 20) /* Update load mode register and extended mode register */
-
-#define AT91_DDRSDRC_MDR 0x20 /* Memory Device Register */
-#define AT91_DDRSDRC_MD (3 << 0) /* Memory Device Type */
-#define AT91_DDRSDRC_MD_SDR 0
-#define AT91_DDRSDRC_MD_LOW_POWER_SDR 1
-#define AT91_DDRSDRC_MD_LOW_POWER_DDR 3
-#define AT91_DDRSDRC_MD_DDR2 6 /* [SAM9 Only] */
-#define AT91_DDRSDRC_DBW (1 << 4) /* Data Bus Width */
-#define AT91_DDRSDRC_DBW_32BITS (0 << 4)
-#define AT91_DDRSDRC_DBW_16BITS (1 << 4)
-
-#define AT91_DDRSDRC_DLL 0x24 /* DLL Information Register */
-#define AT91_DDRSDRC_MDINC (1 << 0) /* Master Delay increment */
-#define AT91_DDRSDRC_MDDEC (1 << 1) /* Master Delay decrement */
-#define AT91_DDRSDRC_MDOVF (1 << 2) /* Master Delay Overflow */
-#define AT91_DDRSDRC_MDVAL (0xff << 8) /* Master Delay value */
-
-#define AT91_DDRSDRC_HS 0x2C /* High Speed Register [SAM9 Only] */
-#define AT91_DDRSDRC_DIS_ATCP_RD (1 << 2) /* Anticip read access is disabled */
-
-#define AT91_DDRSDRC_DELAY(n) (0x30 + (0x4 * (n))) /* Delay I/O Register n */
-
-#define AT91_DDRSDRC_WPMR 0xE4 /* Write Protect Mode Register [SAM9 Only] */
-#define AT91_DDRSDRC_WP (1 << 0) /* Write protect enable */
-#define AT91_DDRSDRC_WPKEY (0xffffff << 8) /* Write protect key */
-#define AT91_DDRSDRC_KEY (0x444452 << 8) /* Write protect key = "DDR" */
-
-#define AT91_DDRSDRC_WPSR 0xE8 /* Write Protect Status Register [SAM9 Only] */
-#define AT91_DDRSDRC_WPVS (1 << 0) /* Write protect violation status */
-#define AT91_DDRSDRC_WPVSRC (0xffff << 8) /* Write protect violation source */
-
-#endif
diff --git a/arch/arm/mach-at91/include/mach/at91sam9_sdramc.h b/arch/arm/mach-at91/include/mach/at91sam9_sdramc.h
deleted file mode 100644
index 3d085a9a7450..000000000000
--- a/arch/arm/mach-at91/include/mach/at91sam9_sdramc.h
+++ /dev/null
@@ -1,85 +0,0 @@
-/*
- * arch/arm/mach-at91/include/mach/at91sam9_sdramc.h
- *
- * Copyright (C) 2007 Andrew Victor
- * Copyright (C) 2007 Atmel Corporation.
- *
- * SDRAM Controllers (SDRAMC) - System peripherals registers.
- * Based on AT91SAM9261 datasheet revision D.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- */
-
-#ifndef AT91SAM9_SDRAMC_H
-#define AT91SAM9_SDRAMC_H
-
-/* SDRAM Controller (SDRAMC) registers */
-#define AT91_SDRAMC_MR 0x00 /* SDRAM Controller Mode Register */
-#define AT91_SDRAMC_MODE (0xf << 0) /* Command Mode */
-#define AT91_SDRAMC_MODE_NORMAL 0
-#define AT91_SDRAMC_MODE_NOP 1
-#define AT91_SDRAMC_MODE_PRECHARGE 2
-#define AT91_SDRAMC_MODE_LMR 3
-#define AT91_SDRAMC_MODE_REFRESH 4
-#define AT91_SDRAMC_MODE_EXT_LMR 5
-#define AT91_SDRAMC_MODE_DEEP 6
-
-#define AT91_SDRAMC_TR 0x04 /* SDRAM Controller Refresh Timer Register */
-#define AT91_SDRAMC_COUNT (0xfff << 0) /* Refresh Timer Counter */
-
-#define AT91_SDRAMC_CR 0x08 /* SDRAM Controller Configuration Register */
-#define AT91_SDRAMC_NC (3 << 0) /* Number of Column Bits */
-#define AT91_SDRAMC_NC_8 (0 << 0)
-#define AT91_SDRAMC_NC_9 (1 << 0)
-#define AT91_SDRAMC_NC_10 (2 << 0)
-#define AT91_SDRAMC_NC_11 (3 << 0)
-#define AT91_SDRAMC_NR (3 << 2) /* Number of Row Bits */
-#define AT91_SDRAMC_NR_11 (0 << 2)
-#define AT91_SDRAMC_NR_12 (1 << 2)
-#define AT91_SDRAMC_NR_13 (2 << 2)
-#define AT91_SDRAMC_NB (1 << 4) /* Number of Banks */
-#define AT91_SDRAMC_NB_2 (0 << 4)
-#define AT91_SDRAMC_NB_4 (1 << 4)
-#define AT91_SDRAMC_CAS (3 << 5) /* CAS Latency */
-#define AT91_SDRAMC_CAS_1 (1 << 5)
-#define AT91_SDRAMC_CAS_2 (2 << 5)
-#define AT91_SDRAMC_CAS_3 (3 << 5)
-#define AT91_SDRAMC_DBW (1 << 7) /* Data Bus Width */
-#define AT91_SDRAMC_DBW_32 (0 << 7)
-#define AT91_SDRAMC_DBW_16 (1 << 7)
-#define AT91_SDRAMC_TWR (0xf << 8) /* Write Recovery Delay */
-#define AT91_SDRAMC_TRC (0xf << 12) /* Row Cycle Delay */
-#define AT91_SDRAMC_TRP (0xf << 16) /* Row Precharge Delay */
-#define AT91_SDRAMC_TRCD (0xf << 20) /* Row to Column Delay */
-#define AT91_SDRAMC_TRAS (0xf << 24) /* Active to Precharge Delay */
-#define AT91_SDRAMC_TXSR (0xf << 28) /* Exit Self Refresh to Active Delay */
-
-#define AT91_SDRAMC_LPR 0x10 /* SDRAM Controller Low Power Register */
-#define AT91_SDRAMC_LPCB (3 << 0) /* Low-power Configurations */
-#define AT91_SDRAMC_LPCB_DISABLE 0
-#define AT91_SDRAMC_LPCB_SELF_REFRESH 1
-#define AT91_SDRAMC_LPCB_POWER_DOWN 2
-#define AT91_SDRAMC_LPCB_DEEP_POWER_DOWN 3
-#define AT91_SDRAMC_PASR (7 << 4) /* Partial Array Self Refresh */
-#define AT91_SDRAMC_TCSR (3 << 8) /* Temperature Compensated Self Refresh */
-#define AT91_SDRAMC_DS (3 << 10) /* Drive Strength */
-#define AT91_SDRAMC_TIMEOUT (3 << 12) /* Time to define when Low Power Mode is enabled */
-#define AT91_SDRAMC_TIMEOUT_0_CLK_CYCLES (0 << 12)
-#define AT91_SDRAMC_TIMEOUT_64_CLK_CYCLES (1 << 12)
-#define AT91_SDRAMC_TIMEOUT_128_CLK_CYCLES (2 << 12)
-
-#define AT91_SDRAMC_IER 0x14 /* SDRAM Controller Interrupt Enable Register */
-#define AT91_SDRAMC_IDR 0x18 /* SDRAM Controller Interrupt Disable Register */
-#define AT91_SDRAMC_IMR 0x1C /* SDRAM Controller Interrupt Mask Register */
-#define AT91_SDRAMC_ISR 0x20 /* SDRAM Controller Interrupt Status Register */
-#define AT91_SDRAMC_RES (1 << 0) /* Refresh Error Status */
-
-#define AT91_SDRAMC_MDR 0x24 /* SDRAM Memory Device Register */
-#define AT91_SDRAMC_MD (3 << 0) /* Memory Device Type */
-#define AT91_SDRAMC_MD_SDRAM 0
-#define AT91_SDRAMC_MD_LOW_POWER_SDRAM 1
-
-#endif
diff --git a/arch/arm/mach-at91/pm.h b/arch/arm/mach-at91/pm.h
index c5101dcb4fb0..d2c89963af2d 100644
--- a/arch/arm/mach-at91/pm.h
+++ b/arch/arm/mach-at91/pm.h
@@ -14,7 +14,6 @@
#include <asm/proc-fns.h>
#include <mach/at91_ramc.h>
-#include <mach/at91rm9200_sdramc.h>
#ifdef CONFIG_PM
extern void at91_pm_set_standby(void (*at91_standby)(void));
diff --git a/drivers/power/reset/at91-reset.c b/drivers/power/reset/at91-reset.c
index 3cb36693343a..69a75d99ae92 100644
--- a/drivers/power/reset/at91-reset.c
+++ b/drivers/power/reset/at91-reset.c
@@ -19,8 +19,8 @@
#include <asm/system_misc.h>
-#include <mach/at91sam9_ddrsdr.h>
-#include <mach/at91sam9_sdramc.h>
+#include <soc/at91/at91sam9_ddrsdr.h>
+#include <soc/at91/at91sam9_sdramc.h>
#define AT91_RSTC_CR 0x00 /* Reset Controller Control Register */
#define AT91_RSTC_PROCRST BIT(0) /* Processor Reset */
diff --git a/include/soc/at91/at91rm9200_sdramc.h b/include/soc/at91/at91rm9200_sdramc.h
new file mode 100644
index 000000000000..aa047f458f1b
--- /dev/null
+++ b/include/soc/at91/at91rm9200_sdramc.h
@@ -0,0 +1,63 @@
+/*
+ * arch/arm/mach-at91/include/mach/at91rm9200_sdramc.h
+ *
+ * Copyright (C) 2005 Ivan Kokshaysky
+ * Copyright (C) SAN People
+ *
+ * Memory Controllers (SDRAMC only) - System peripherals registers.
+ * Based on AT91RM9200 datasheet revision E.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+
+#ifndef AT91RM9200_SDRAMC_H
+#define AT91RM9200_SDRAMC_H
+
+/* SDRAM Controller registers */
+#define AT91RM9200_SDRAMC_MR 0x90 /* Mode Register */
+#define AT91RM9200_SDRAMC_MODE (0xf << 0) /* Command Mode */
+#define AT91RM9200_SDRAMC_MODE_NORMAL (0 << 0)
+#define AT91RM9200_SDRAMC_MODE_NOP (1 << 0)
+#define AT91RM9200_SDRAMC_MODE_PRECHARGE (2 << 0)
+#define AT91RM9200_SDRAMC_MODE_LMR (3 << 0)
+#define AT91RM9200_SDRAMC_MODE_REFRESH (4 << 0)
+#define AT91RM9200_SDRAMC_DBW (1 << 4) /* Data Bus Width */
+#define AT91RM9200_SDRAMC_DBW_32 (0 << 4)
+#define AT91RM9200_SDRAMC_DBW_16 (1 << 4)
+
+#define AT91RM9200_SDRAMC_TR 0x94 /* Refresh Timer Register */
+#define AT91RM9200_SDRAMC_COUNT (0xfff << 0) /* Refresh Timer Count */
+
+#define AT91RM9200_SDRAMC_CR 0x98 /* Configuration Register */
+#define AT91RM9200_SDRAMC_NC (3 << 0) /* Number of Column Bits */
+#define AT91RM9200_SDRAMC_NC_8 (0 << 0)
+#define AT91RM9200_SDRAMC_NC_9 (1 << 0)
+#define AT91RM9200_SDRAMC_NC_10 (2 << 0)
+#define AT91RM9200_SDRAMC_NC_11 (3 << 0)
+#define AT91RM9200_SDRAMC_NR (3 << 2) /* Number of Row Bits */
+#define AT91RM9200_SDRAMC_NR_11 (0 << 2)
+#define AT91RM9200_SDRAMC_NR_12 (1 << 2)
+#define AT91RM9200_SDRAMC_NR_13 (2 << 2)
+#define AT91RM9200_SDRAMC_NB (1 << 4) /* Number of Banks */
+#define AT91RM9200_SDRAMC_NB_2 (0 << 4)
+#define AT91RM9200_SDRAMC_NB_4 (1 << 4)
+#define AT91RM9200_SDRAMC_CAS (3 << 5) /* CAS Latency */
+#define AT91RM9200_SDRAMC_CAS_2 (2 << 5)
+#define AT91RM9200_SDRAMC_TWR (0xf << 7) /* Write Recovery Delay */
+#define AT91RM9200_SDRAMC_TRC (0xf << 11) /* Row Cycle Delay */
+#define AT91RM9200_SDRAMC_TRP (0xf << 15) /* Row Precharge Delay */
+#define AT91RM9200_SDRAMC_TRCD (0xf << 19) /* Row to Column Delay */
+#define AT91RM9200_SDRAMC_TRAS (0xf << 23) /* Active to Precharge Delay */
+#define AT91RM9200_SDRAMC_TXSR (0xf << 27) /* Exit Self Refresh to Active Delay */
+
+#define AT91RM9200_SDRAMC_SRR 0x9c /* Self Refresh Register */
+#define AT91RM9200_SDRAMC_LPR 0xa0 /* Low Power Register */
+#define AT91RM9200_SDRAMC_IER 0xa4 /* Interrupt Enable Register */
+#define AT91RM9200_SDRAMC_IDR 0xa8 /* Interrupt Disable Register */
+#define AT91RM9200_SDRAMC_IMR 0xac /* Interrupt Mask Register */
+#define AT91RM9200_SDRAMC_ISR 0xb0 /* Interrupt Status Register */
+
+#endif
diff --git a/include/soc/at91/at91sam9_ddrsdr.h b/include/soc/at91/at91sam9_ddrsdr.h
new file mode 100644
index 000000000000..0210797abf2e
--- /dev/null
+++ b/include/soc/at91/at91sam9_ddrsdr.h
@@ -0,0 +1,124 @@
+/*
+ * Header file for the Atmel DDR/SDR SDRAM Controller
+ *
+ * Copyright (C) 2010 Atmel Corporation
+ * Nicolas Ferre <nicolas.ferre at atmel.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+#ifndef AT91SAM9_DDRSDR_H
+#define AT91SAM9_DDRSDR_H
+
+#define AT91_DDRSDRC_MR 0x00 /* Mode Register */
+#define AT91_DDRSDRC_MODE (0x7 << 0) /* Command Mode */
+#define AT91_DDRSDRC_MODE_NORMAL 0
+#define AT91_DDRSDRC_MODE_NOP 1
+#define AT91_DDRSDRC_MODE_PRECHARGE 2
+#define AT91_DDRSDRC_MODE_LMR 3
+#define AT91_DDRSDRC_MODE_REFRESH 4
+#define AT91_DDRSDRC_MODE_EXT_LMR 5
+#define AT91_DDRSDRC_MODE_DEEP 6
+
+#define AT91_DDRSDRC_RTR 0x04 /* Refresh Timer Register */
+#define AT91_DDRSDRC_COUNT (0xfff << 0) /* Refresh Timer Counter */
+
+#define AT91_DDRSDRC_CR 0x08 /* Configuration Register */
+#define AT91_DDRSDRC_NC (3 << 0) /* Number of Column Bits */
+#define AT91_DDRSDRC_NC_SDR8 (0 << 0)
+#define AT91_DDRSDRC_NC_SDR9 (1 << 0)
+#define AT91_DDRSDRC_NC_SDR10 (2 << 0)
+#define AT91_DDRSDRC_NC_SDR11 (3 << 0)
+#define AT91_DDRSDRC_NC_DDR9 (0 << 0)
+#define AT91_DDRSDRC_NC_DDR10 (1 << 0)
+#define AT91_DDRSDRC_NC_DDR11 (2 << 0)
+#define AT91_DDRSDRC_NC_DDR12 (3 << 0)
+#define AT91_DDRSDRC_NR (3 << 2) /* Number of Row Bits */
+#define AT91_DDRSDRC_NR_11 (0 << 2)
+#define AT91_DDRSDRC_NR_12 (1 << 2)
+#define AT91_DDRSDRC_NR_13 (2 << 2)
+#define AT91_DDRSDRC_NR_14 (3 << 2)
+#define AT91_DDRSDRC_CAS (7 << 4) /* CAS Latency */
+#define AT91_DDRSDRC_CAS_2 (2 << 4)
+#define AT91_DDRSDRC_CAS_3 (3 << 4)
+#define AT91_DDRSDRC_CAS_25 (6 << 4)
+#define AT91_DDRSDRC_RST_DLL (1 << 7) /* Reset DLL */
+#define AT91_DDRSDRC_DICDS (1 << 8) /* Output impedance control */
+#define AT91_DDRSDRC_DIS_DLL (1 << 9) /* Disable DLL [SAM9 Only] */
+#define AT91_DDRSDRC_OCD (1 << 12) /* Off-Chip Driver [SAM9 Only] */
+#define AT91_DDRSDRC_DQMS (1 << 16) /* Mask Data is Shared [SAM9 Only] */
+#define AT91_DDRSDRC_ACTBST (1 << 18) /* Active Bank X to Burst Stop Read Access Bank Y [SAM9 Only] */
+
+#define AT91_DDRSDRC_T0PR 0x0C /* Timing 0 Register */
+#define AT91_DDRSDRC_TRAS (0xf << 0) /* Active to Precharge delay */
+#define AT91_DDRSDRC_TRCD (0xf << 4) /* Row to Column delay */
+#define AT91_DDRSDRC_TWR (0xf << 8) /* Write recovery delay */
+#define AT91_DDRSDRC_TRC (0xf << 12) /* Row cycle delay */
+#define AT91_DDRSDRC_TRP (0xf << 16) /* Row precharge delay */
+#define AT91_DDRSDRC_TRRD (0xf << 20) /* Active BankA to BankB */
+#define AT91_DDRSDRC_TWTR (0x7 << 24) /* Internal Write to Read delay */
+#define AT91_DDRSDRC_RED_WRRD (0x1 << 27) /* Reduce Write to Read Delay [SAM9 Only] */
+#define AT91_DDRSDRC_TMRD (0xf << 28) /* Load mode to active/refresh delay */
+
+#define AT91_DDRSDRC_T1PR 0x10 /* Timing 1 Register */
+#define AT91_DDRSDRC_TRFC (0x1f << 0) /* Row Cycle Delay */
+#define AT91_DDRSDRC_TXSNR (0xff << 8) /* Exit self-refresh to non-read */
+#define AT91_DDRSDRC_TXSRD (0xff << 16) /* Exit self-refresh to read */
+#define AT91_DDRSDRC_TXP (0xf << 24) /* Exit power-down delay */
+
+#define AT91_DDRSDRC_T2PR 0x14 /* Timing 2 Register [SAM9 Only] */
+#define AT91_DDRSDRC_TXARD (0xf << 0) /* Exit active power down delay to read command in mode "Fast Exit" */
+#define AT91_DDRSDRC_TXARDS (0xf << 4) /* Exit active power down delay to read command in mode "Slow Exit" */
+#define AT91_DDRSDRC_TRPA (0xf << 8) /* Row Precharge All delay */
+#define AT91_DDRSDRC_TRTP (0x7 << 12) /* Read to Precharge delay */
+
+#define AT91_DDRSDRC_LPR 0x1C /* Low Power Register */
+#define AT91_DDRSDRC_LPCB (3 << 0) /* Low-power Configurations */
+#define AT91_DDRSDRC_LPCB_DISABLE 0
+#define AT91_DDRSDRC_LPCB_SELF_REFRESH 1
+#define AT91_DDRSDRC_LPCB_POWER_DOWN 2
+#define AT91_DDRSDRC_LPCB_DEEP_POWER_DOWN 3
+#define AT91_DDRSDRC_CLKFR (1 << 2) /* Clock Frozen */
+#define AT91_DDRSDRC_PASR (7 << 4) /* Partial Array Self Refresh */
+#define AT91_DDRSDRC_TCSR (3 << 8) /* Temperature Compensated Self Refresh */
+#define AT91_DDRSDRC_DS (3 << 10) /* Drive Strength */
+#define AT91_DDRSDRC_TIMEOUT (3 << 12) /* Time to define when Low Power Mode is enabled */
+#define AT91_DDRSDRC_TIMEOUT_0_CLK_CYCLES (0 << 12)
+#define AT91_DDRSDRC_TIMEOUT_64_CLK_CYCLES (1 << 12)
+#define AT91_DDRSDRC_TIMEOUT_128_CLK_CYCLES (2 << 12)
+#define AT91_DDRSDRC_APDE (1 << 16) /* Active power down exit time */
+#define AT91_DDRSDRC_UPD_MR (3 << 20) /* Update load mode register and extended mode register */
+
+#define AT91_DDRSDRC_MDR 0x20 /* Memory Device Register */
+#define AT91_DDRSDRC_MD (3 << 0) /* Memory Device Type */
+#define AT91_DDRSDRC_MD_SDR 0
+#define AT91_DDRSDRC_MD_LOW_POWER_SDR 1
+#define AT91_DDRSDRC_MD_LOW_POWER_DDR 3
+#define AT91_DDRSDRC_MD_DDR2 6 /* [SAM9 Only] */
+#define AT91_DDRSDRC_DBW (1 << 4) /* Data Bus Width */
+#define AT91_DDRSDRC_DBW_32BITS (0 << 4)
+#define AT91_DDRSDRC_DBW_16BITS (1 << 4)
+
+#define AT91_DDRSDRC_DLL 0x24 /* DLL Information Register */
+#define AT91_DDRSDRC_MDINC (1 << 0) /* Master Delay increment */
+#define AT91_DDRSDRC_MDDEC (1 << 1) /* Master Delay decrement */
+#define AT91_DDRSDRC_MDOVF (1 << 2) /* Master Delay Overflow */
+#define AT91_DDRSDRC_MDVAL (0xff << 8) /* Master Delay value */
+
+#define AT91_DDRSDRC_HS 0x2C /* High Speed Register [SAM9 Only] */
+#define AT91_DDRSDRC_DIS_ATCP_RD (1 << 2) /* Anticip read access is disabled */
+
+#define AT91_DDRSDRC_DELAY(n) (0x30 + (0x4 * (n))) /* Delay I/O Register n */
+
+#define AT91_DDRSDRC_WPMR 0xE4 /* Write Protect Mode Register [SAM9 Only] */
+#define AT91_DDRSDRC_WP (1 << 0) /* Write protect enable */
+#define AT91_DDRSDRC_WPKEY (0xffffff << 8) /* Write protect key */
+#define AT91_DDRSDRC_KEY (0x444452 << 8) /* Write protect key = "DDR" */
+
+#define AT91_DDRSDRC_WPSR 0xE8 /* Write Protect Status Register [SAM9 Only] */
+#define AT91_DDRSDRC_WPVS (1 << 0) /* Write protect violation status */
+#define AT91_DDRSDRC_WPVSRC (0xffff << 8) /* Write protect violation source */
+
+#endif
diff --git a/include/soc/at91/at91sam9_sdramc.h b/include/soc/at91/at91sam9_sdramc.h
new file mode 100644
index 000000000000..3d085a9a7450
--- /dev/null
+++ b/include/soc/at91/at91sam9_sdramc.h
@@ -0,0 +1,85 @@
+/*
+ * arch/arm/mach-at91/include/mach/at91sam9_sdramc.h
+ *
+ * Copyright (C) 2007 Andrew Victor
+ * Copyright (C) 2007 Atmel Corporation.
+ *
+ * SDRAM Controllers (SDRAMC) - System peripherals registers.
+ * Based on AT91SAM9261 datasheet revision D.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+
+#ifndef AT91SAM9_SDRAMC_H
+#define AT91SAM9_SDRAMC_H
+
+/* SDRAM Controller (SDRAMC) registers */
+#define AT91_SDRAMC_MR 0x00 /* SDRAM Controller Mode Register */
+#define AT91_SDRAMC_MODE (0xf << 0) /* Command Mode */
+#define AT91_SDRAMC_MODE_NORMAL 0
+#define AT91_SDRAMC_MODE_NOP 1
+#define AT91_SDRAMC_MODE_PRECHARGE 2
+#define AT91_SDRAMC_MODE_LMR 3
+#define AT91_SDRAMC_MODE_REFRESH 4
+#define AT91_SDRAMC_MODE_EXT_LMR 5
+#define AT91_SDRAMC_MODE_DEEP 6
+
+#define AT91_SDRAMC_TR 0x04 /* SDRAM Controller Refresh Timer Register */
+#define AT91_SDRAMC_COUNT (0xfff << 0) /* Refresh Timer Counter */
+
+#define AT91_SDRAMC_CR 0x08 /* SDRAM Controller Configuration Register */
+#define AT91_SDRAMC_NC (3 << 0) /* Number of Column Bits */
+#define AT91_SDRAMC_NC_8 (0 << 0)
+#define AT91_SDRAMC_NC_9 (1 << 0)
+#define AT91_SDRAMC_NC_10 (2 << 0)
+#define AT91_SDRAMC_NC_11 (3 << 0)
+#define AT91_SDRAMC_NR (3 << 2) /* Number of Row Bits */
+#define AT91_SDRAMC_NR_11 (0 << 2)
+#define AT91_SDRAMC_NR_12 (1 << 2)
+#define AT91_SDRAMC_NR_13 (2 << 2)
+#define AT91_SDRAMC_NB (1 << 4) /* Number of Banks */
+#define AT91_SDRAMC_NB_2 (0 << 4)
+#define AT91_SDRAMC_NB_4 (1 << 4)
+#define AT91_SDRAMC_CAS (3 << 5) /* CAS Latency */
+#define AT91_SDRAMC_CAS_1 (1 << 5)
+#define AT91_SDRAMC_CAS_2 (2 << 5)
+#define AT91_SDRAMC_CAS_3 (3 << 5)
+#define AT91_SDRAMC_DBW (1 << 7) /* Data Bus Width */
+#define AT91_SDRAMC_DBW_32 (0 << 7)
+#define AT91_SDRAMC_DBW_16 (1 << 7)
+#define AT91_SDRAMC_TWR (0xf << 8) /* Write Recovery Delay */
+#define AT91_SDRAMC_TRC (0xf << 12) /* Row Cycle Delay */
+#define AT91_SDRAMC_TRP (0xf << 16) /* Row Precharge Delay */
+#define AT91_SDRAMC_TRCD (0xf << 20) /* Row to Column Delay */
+#define AT91_SDRAMC_TRAS (0xf << 24) /* Active to Precharge Delay */
+#define AT91_SDRAMC_TXSR (0xf << 28) /* Exit Self Refresh to Active Delay */
+
+#define AT91_SDRAMC_LPR 0x10 /* SDRAM Controller Low Power Register */
+#define AT91_SDRAMC_LPCB (3 << 0) /* Low-power Configurations */
+#define AT91_SDRAMC_LPCB_DISABLE 0
+#define AT91_SDRAMC_LPCB_SELF_REFRESH 1
+#define AT91_SDRAMC_LPCB_POWER_DOWN 2
+#define AT91_SDRAMC_LPCB_DEEP_POWER_DOWN 3
+#define AT91_SDRAMC_PASR (7 << 4) /* Partial Array Self Refresh */
+#define AT91_SDRAMC_TCSR (3 << 8) /* Temperature Compensated Self Refresh */
+#define AT91_SDRAMC_DS (3 << 10) /* Drive Strength */
+#define AT91_SDRAMC_TIMEOUT (3 << 12) /* Time to define when Low Power Mode is enabled */
+#define AT91_SDRAMC_TIMEOUT_0_CLK_CYCLES (0 << 12)
+#define AT91_SDRAMC_TIMEOUT_64_CLK_CYCLES (1 << 12)
+#define AT91_SDRAMC_TIMEOUT_128_CLK_CYCLES (2 << 12)
+
+#define AT91_SDRAMC_IER 0x14 /* SDRAM Controller Interrupt Enable Register */
+#define AT91_SDRAMC_IDR 0x18 /* SDRAM Controller Interrupt Disable Register */
+#define AT91_SDRAMC_IMR 0x1C /* SDRAM Controller Interrupt Mask Register */
+#define AT91_SDRAMC_ISR 0x20 /* SDRAM Controller Interrupt Status Register */
+#define AT91_SDRAMC_RES (1 << 0) /* Refresh Error Status */
+
+#define AT91_SDRAMC_MDR 0x24 /* SDRAM Memory Device Register */
+#define AT91_SDRAMC_MD (3 << 0) /* Memory Device Type */
+#define AT91_SDRAMC_MD_SDRAM 0
+#define AT91_SDRAMC_MD_LOW_POWER_SDRAM 1
+
+#endif
--
2.1.0
More information about the linux-arm-kernel
mailing list