[PATCH 3/4] arm: boot: dts: am335x-evm: Make charge delay a DT parameter for tsc

Vignesh R vigneshr at ti.com
Thu Nov 6 21:48:16 PST 2014



On Saturday 01 November 2014 02:39 AM, Hartmut Knaack wrote:
> Vignesh R schrieb am 27.10.2014 12:08:
>> The charge delay value is by default 0xB000. But it can be set to lower
>> values on some boards as long as false pen-ups are avoided. Lowering the
>> value increases the sampling rate (though current sampling rate is
>> sufficient for tsc operation). Hence charge delay has been made a DT
>> parameter.
>>
> I would recommend to use a few colons to separate some thoughts. Also, limit to 80 chars per line would be beneficial. See inline.

I will address this in v2

>> Signed-off-by: Vignesh R <vigneshr at ti.com>
>> ---
>>  .../devicetree/bindings/input/touchscreen/ti-tsc-adc.txt    | 13 +++++++++++++
>>  arch/arm/boot/dts/am335x-evm.dts                            |  1 +
>>  2 files changed, 14 insertions(+)
>>
>> diff --git a/Documentation/devicetree/bindings/input/touchscreen/ti-tsc-adc.txt b/Documentation/devicetree/bindings/input/touchscreen/ti-tsc-adc.txt
>> index 878549ba814d..ac62769e70e4 100644
>> --- a/Documentation/devicetree/bindings/input/touchscreen/ti-tsc-adc.txt
>> +++ b/Documentation/devicetree/bindings/input/touchscreen/ti-tsc-adc.txt
>> @@ -28,6 +28,18 @@ Required properties:
>>  	ti,adc-channels: List of analog inputs available for ADC.
>>  			 AIN0 = 0, AIN1 = 1 and so on till AIN7 = 7.
>>  
>> +Optional properties:
>> +- child "tsc"
>> +	ti,charge-delay: Length of touch screen charge delay step in terms of
>> +			 ADC clock cycles. Charge delay value should be large in order
>> +			 to avoid false pen-up events. This value affects the overall
>> +			 sampling speed hence need to be kept as low as possible while
> <...> speed, hence needs to be <...>
>> +			 avoiding false pen-up event. Start from a lower value say 0x400
> <...> pen-up events. Start from a lower value, like 0x400, and increase <...>
>> +			 and increase value until false pen-up events are avoided. The
>> +			 pen-up detection happens immediately after the charge step
> <...> charge step, so this <...>
>> +			 so this does in fact function as a hardware knob for adjusting
>> +			 the amount of "settling time".
>> +
>>  Example:
>>  	tscadc: tscadc at 44e0d000 {
>>  		compatible = "ti,am3359-tscadc";
>> @@ -36,6 +48,7 @@ Example:
>>  			ti,x-plate-resistance = <200>;
>>  			ti,coordiante-readouts = <5>;
>>  			ti,wire-config = <0x00 0x11 0x22 0x33>;
>> +			ti,charge-delay = <0xB000>;
>>  		};
>>  
>>  		adc {
>> diff --git a/arch/arm/boot/dts/am335x-evm.dts b/arch/arm/boot/dts/am335x-evm.dts
>> index e2156a583de7..80be0462298b 100644
>> --- a/arch/arm/boot/dts/am335x-evm.dts
>> +++ b/arch/arm/boot/dts/am335x-evm.dts
>> @@ -641,6 +641,7 @@
>>  		ti,x-plate-resistance = <200>;
>>  		ti,coordinate-readouts = <5>;
>>  		ti,wire-config = <0x00 0x11 0x22 0x33>;
>> +		ti,charge-delay = <0xB000>;
>>  	};
>>  
>>  	adc {
>>
> 



More information about the linux-arm-kernel mailing list