[PATCH] ARM: dts: Add am57xx-beagle-x15
Nishanth Menon
nm at ti.com
Thu Nov 6 09:00:10 PST 2014
On 10:53-20141106, Nishanth Menon wrote:
> On 11/06/2014 10:48 AM, Tony Lindgren wrote:
> > * Nishanth Menon <nm at ti.com> [141106 08:44]:
> >> On 11/06/2014 10:37 AM, Tom Rini wrote:
> >>
> >>>>> device_type = "memory"; + reg = <0x80000000 0x40000000>; /* 1GB
> >>>>> to start. Target 2GB */
> >>>>
> >>>> 1GiB ? Why would you put this here btw ? u-boot fills this one up.
> >>>
> >>> Yes, it should either be the full and correct value or 0x0 (like a
> >>> number of PowerPC platforms do) so it's clear something else gives us
> >>> the right value here.
> >>
> >> Honest mistake, my bad.. I thought I cleaned up the patch! Sigh!!! i
> >> will repost with proper 2GB. it is better that way in case being used
> >> with "other bootloaders" which are not exactly too good like u-boot.
> >
> > Can you also describe why all the always-on regulators are needed?
> yep - will do that similar to
> https://patchwork.kernel.org/patch/5125431/ - same rationale unless
> there is any specific voltage rail that you are explicitly interested
> in that needs additional explanation. Is there additional rails of
> interest?
Here is what I have in mind: (updated with comments from Felipe/Tom and
above) - would you like more details added - if you could point out
areas of interest, I can help improve information provided here.
8<---
>From d73029bc01c9e2193fb769ce5cc6cc5abb14eba5 Mon Sep 17 00:00:00 2001
From: Nishanth Menon <nm at ti.com>
Date: Mon, 18 Aug 2014 12:14:08 -0500
Subject: [PATCH V2] ARM: dts: Add am57xx-beagle-x15
BeagleBoard-X15 is the next generation Open Source Hardware
BeagleBoard based on TI's AM5728 SoC featuring dual core 1.5GHZ A15
processor. The platform features 2GB DDR3L (w/dual 32bit busses),
eSATA, 3 USB3.0 ports, integrated HDMI (1920x108 at 60), separate LCD
port, video In port, 4GB eMMC, uSD, Analog audio in/out, dual 1G
Ethernet.
For more information, refer to:
BeagleBoard-X15 Wiki:
http://www.elinux.org/Beagleboard:BeagleBoard-X15
AM5728 is part of the Sitara product family whose additional details
will be available: http://www.ti.com/lsds/ti/arm/overview.page
Technical Reference Manual for AM5728 is public domain at:
http://www.ti.com/lit/spruhz6
Just add basic support for the moment, the following updates are needed:
i) Ethernet - depends on SoC dts fixes
ii) USB Client (USB2) - depends on GPIO extcon
ii) HDMI - additional driver fixes pending
iii) Audio - additional driver fixes pending
NOTE:
AM5728 Data Manual (SPRS915L - August 2014) section 4.1.1 states: "All
unused power supply balls must be supplied with the voltages specified
in the Section 5.2, Recommended Operating Conditions". This implies
that all unused voltage rails for AM5728 can never be switched off even
if the hardware blocks inside that voltage domain is unused. Switching
off these unused rails may result in stability issues on other domains
and increased leakage and power-on-hour impacts.
Signed-off-by: Felipe Balbi <balbi at ti.com>
Signed-off-by: Nishanth Menon <nm at ti.com>
---
Changes in V2 since V1:
- Fix the missing squash of proper DDR size.
V1: https://patchwork.kernel.org/patch/5244801/
Additional references:
- Missing ethernet dtsi patch series: http://marc.info/?t=141388585300001&r=1&w=2
- Missing USB Client extcon patch series: http://marc.info/?t=141520160800004&r=1&w=2
Tested with omap2plus_defconfig modified as: http://slexy.org/view/s2DRTzUwjj
boot log: http://slexy.org/raw/s25Grf1uoo
based on 3.18-rc1 tag.
Support for u-boot has been posted as well: (series ending
http://patchwork.ozlabs.org/patch/407552/ )
Side note: this patch generates a few unrelated checkpatch warning for
compatible which probably is part of appropriate driver documentation
fixes (functionality is already present).
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/am57xx-beagle-x15.dts | 405 +++++++++++++++++++++++++++++++
2 files changed, 406 insertions(+)
create mode 100644 arch/arm/boot/dts/am57xx-beagle-x15.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 38c89ca..eee1e4f 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -347,6 +347,7 @@ dtb-$(CONFIG_SOC_OMAP5) += omap5-cm-t54.dtb \
omap5-sbc-t54.dtb \
omap5-uevm.dtb
dtb-$(CONFIG_SOC_DRA7XX) += dra7-evm.dtb \
+ am57xx-beagle-x15.dtb \
dra72-evm.dtb
dtb-$(CONFIG_ARCH_ORION5X) += orion5x-lacie-d2-network.dtb \
orion5x-lacie-ethernet-disk-mini-v2.dtb \
diff --git a/arch/arm/boot/dts/am57xx-beagle-x15.dts b/arch/arm/boot/dts/am57xx-beagle-x15.dts
new file mode 100644
index 0000000..1f1875b
--- /dev/null
+++ b/arch/arm/boot/dts/am57xx-beagle-x15.dts
@@ -0,0 +1,405 @@
+/*
+ * Copyright (C) 2014 Texas Instruments Incorporated - http://www.ti.com/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+/dts-v1/;
+
+#include "dra74x.dtsi"
+#include <dt-bindings/clk/ti-dra7-atl.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/ {
+ model = "TI AM5728 BeagleBoard-X15";
+ compatible = "ti,am572x-beagle-x15", "ti,am5728", "ti,dra742", "ti,dra74", "ti,dra7";
+
+ aliases {
+ rtc0 = &mcp_rtc;
+ rtc1 = &tps659038_rtc;
+ };
+
+ memory {
+ device_type = "memory";
+ reg = <0x80000000 0x80000000>;
+ };
+
+ vdd_3v3: fixedregulator-vdd_3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "vdd_3v3";
+ vin-supply = <®en1>;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ vtt_fixed: fixedregulator-vtt {
+ /* TPS51200 */
+ compatible = "regulator-fixed";
+ regulator-name = "vtt_fixed";
+ vin-supply = <&smps3_reg>;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ regulator-boot-on;
+ enable-active-high;
+ gpio = <&gpio7 11 GPIO_ACTIVE_HIGH>;
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&leds_pins_default>;
+
+ led at 0 {
+ label = "beagle-x15:usr0";
+ gpios = <&gpio7 9 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "heartbeat";
+ default-state = "off";
+ };
+
+ led at 1 {
+ label = "beagle-x15:usr1";
+ gpios = <&gpio7 8 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "cpu0";
+ default-state = "off";
+ };
+
+ led at 2 {
+ label = "beagle-x15:usr2";
+ gpios = <&gpio7 14 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "mmc0";
+ default-state = "off";
+ };
+
+ led at 3 {
+ label = "beagle-x15:usr3";
+ gpios = <&gpio7 15 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "ide-disk";
+ default-state = "off";
+ };
+ };
+};
+
+&dra7_pmx_core {
+ leds_pins_default: leds_pins_default {
+ pinctrl-single,pins = <
+ 0x3a8 (PIN_OUTPUT | MUX_MODE14) /* spi1_d1.gpio7_8 */
+ 0x3ac (PIN_OUTPUT | MUX_MODE14) /* spi1_d0.gpio7_9 */
+ 0x3c0 (PIN_OUTPUT | MUX_MODE14) /* spi2_sclk.gpio7_14 */
+ 0x3c4 (PIN_OUTPUT | MUX_MODE14) /* spi2_d1.gpio7_15 */
+ >;
+ };
+
+ i2c1_pins_default: i2c1_pins_default {
+ pinctrl-single,pins = <
+ 0x400 (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c1_sda.sda */
+ 0x404 (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c1_scl.scl */
+ >;
+ };
+
+ i2c3_pins_default: i2c3_pins_default {
+ pinctrl-single,pins = <
+ 0x2a4 (PIN_INPUT| MUX_MODE10) /* mcasp1_aclkx.i2c3_sda */
+ 0x2a8 (PIN_INPUT| MUX_MODE10) /* mcasp1_fsx.i2c3_scl */
+ >;
+ };
+
+ uart3_pins_default: uart3_pins_default {
+ pinctrl-single,pins = <
+ 0x248 (PIN_INPUT_SLEW | MUX_MODE0) /* uart3_rxd.rxd */
+ 0x24c (PIN_INPUT_SLEW | MUX_MODE0) /* uart3_txd.txd */
+ >;
+ };
+
+ mmc1_pins_default: mmc1_pins_default {
+ pinctrl-single,pins = <
+ 0x36c (PIN_INPUT | MUX_MODE14) /* mmc1sdcd.gpio219 */
+ 0x354 (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_clk.clk */
+ 0x358 (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_cmd.cmd */
+ 0x35c (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat0.dat0 */
+ 0x360 (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat1.dat1 */
+ 0x364 (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat2.dat2 */
+ 0x368 (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat3.dat3 */
+ >;
+ };
+
+ mmc2_pins_default: mmc2_pins_default {
+ pinctrl-single,pins = <
+ 0x9c (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a23.mmc2_clk */
+ 0xb0 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_cs1.mmc2_cmd */
+ 0xa0 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a24.mmc2_dat0 */
+ 0xa4 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a25.mmc2_dat1 */
+ 0xa8 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a26.mmc2_dat2 */
+ 0xac (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a27.mmc2_dat3 */
+ 0x8c (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a19.mmc2_dat4 */
+ 0x90 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a20.mmc2_dat5 */
+ 0x94 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a21.mmc2_dat6 */
+ 0x98 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a22.mmc2_dat7 */
+ >;
+ };
+
+ tps659038_pins_default: tps659038_pins_default {
+ pinctrl-single,pins = <
+ 0x418 (PIN_INPUT_PULLUP | MUX_MODE14) /* wakeup0.gpio1_0 */
+ >;
+ };
+
+ tmp102_pins_default: tmp102_pins_default {
+ pinctrl-single,pins = <
+ 0x3C8 (PIN_INPUT_PULLUP | MUX_MODE14) /* spi2_d0.gpio7_16 */
+ >;
+ };
+
+ mcp79410_pins_default: mcp79410_pins_default {
+ pinctrl-single,pins = <
+ 0x424 (PIN_INPUT_PULLUP | MUX_MODE1) /* wakeup3.sys_nirq1 */
+ >;
+ };
+
+ usb1_pins: pinmux_usb1_pins {
+ pinctrl-single,pins = <
+ 0x280 (PIN_INPUT_SLEW | MUX_MODE0) /* usb1_drvvbus */
+ >;
+ };
+
+};
+
+&i2c1 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c1_pins_default>;
+ clock-frequency = <400000>;
+
+ tps659038: tps659038 at 58 {
+ compatible = "ti,tps659038";
+ reg = <0x58>;
+ interrupt-parent = <&gpio1>;
+ interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&tps659038_pins_default>;
+
+ #interrupt-cells = <2>;
+ interrupt-controller;
+
+ ti,system-power-controller;
+
+ tps659038_pmic {
+ compatible = "ti,tps659038-pmic";
+
+ regulators {
+ smps12_reg: smps12 {
+ /* VDD_MPU */
+ regulator-name = "smps12";
+ regulator-min-microvolt = < 850000>;
+ regulator-max-microvolt = <1250000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ smps3_reg: smps3 {
+ /* VDD_DDR */
+ regulator-name = "smps3";
+ regulator-min-microvolt = <1350000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ smps45_reg: smps45 {
+ /* VDD_DSPEVE, VDD_IVA, VDD_GPU */
+ regulator-name = "smps45";
+ regulator-min-microvolt = < 850000>;
+ regulator-max-microvolt = <1150000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ smps6_reg: smps6 {
+ /* VDD_CORE */
+ regulator-name = "smps6";
+ regulator-min-microvolt = <850000>;
+ regulator-max-microvolt = <1030000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ /* SMPS7 unused */
+
+ smps8_reg: smps8 {
+ /* VDD_1V8 */
+ regulator-name = "smps8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ /* SMPS9 unused */
+
+ ldo1_reg: ldo1 {
+ /* VDD_SD */
+ regulator-name = "ldo1";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ };
+
+ ldo2_reg: ldo2 {
+ /* VDD_SHV5 */
+ regulator-name = "ldo2";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ ldo3_reg: ldo3 {
+ /* VDDA_1V8_PHY */
+ regulator-name = "ldo3";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ ldo9_reg: ldo9 {
+ /* VDD_RTC */
+ regulator-name = "ldo9";
+ regulator-min-microvolt = <1050000>;
+ regulator-max-microvolt = <1050000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ ldoln_reg: ldoln {
+ /* VDDA_1V8_PLL */
+ regulator-name = "ldoln";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ ldousb_reg: ldousb {
+ /* VDDA_3V_USB: VDDA_USBHS33 */
+ regulator-name = "ldousb";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ };
+
+ regen1: regen1 {
+ /* VDD_3V3_ON */
+ regulator-name = "regen1";
+ regulator-boot-on;
+ regulator-always-on;
+ };
+ };
+ };
+
+ tps659038_rtc: tps659038_rtc {
+ compatible = "ti,palmas-rtc";
+ interrupt-parent = <&tps659038>;
+ interrupts = <8 IRQ_TYPE_NONE>;
+ wakeup-source;
+ };
+
+ tps659038_pwr_button: tps659038_pwr_button {
+ compatible = "ti,palmas-pwrbutton";
+ interrupt-parent = <&tps659038>;
+ interrupts = <1 IRQ_TYPE_NONE>;
+ wakeup-source;
+ ti,palmas-long-press-seconds = <12>;
+ };
+ };
+
+ tmp102: tmp102 at 48 {
+ compatible = "ti,tmp102";
+ reg = <0x48>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&tmp102_pins_default>;
+ interrupt-parent = <&gpio7>;
+ interrupts = <16 IRQ_TYPE_LEVEL_LOW>;
+ };
+};
+
+&i2c3 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c3_pins_default>;
+ clock-frequency = <400000>;
+
+ mcp_rtc: rtc at 6f {
+ compatible = "microchip,mcp7941x";
+ reg = <0x6f>;
+ interrupt-parent = <&gic>;
+ interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_LOW>; /* IRQ_SYS_1N */
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&mcp79410_pins_default>;
+
+ vcc-supply = <&vdd_3v3>;
+ wakeup-source;
+ };
+};
+
+&gpio7 {
+ ti,no-reset-on-init;
+ ti,no-idle-on-init;
+};
+
+&cpu0 {
+ cpu0-supply = <&smps12_reg>;
+ voltage-tolerance = <1>;
+};
+
+&uart3 {
+ status = "okay";
+ interrupts-extended = <&gic GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>,
+ <&dra7_pmx_core 0x248>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart3_pins_default>;
+};
+
+&mmc1 {
+ status = "okay";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc1_pins_default>;
+
+ vmmc-supply = <&ldo1_reg>;
+ vmmc_aux-supply = <&vdd_3v3>;
+ pbias-supply = <&pbias_mmc_reg>;
+ bus-width = <4>;
+ cd-gpios = <&gpio6 27 0>; /* gpio 219 */
+};
+
+&mmc2 {
+ status = "okay";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc2_pins_default>;
+
+ vmmc-supply = <&vdd_3v3>;
+ bus-width = <8>;
+ ti,non-removable;
+ cap-mmc-dual-data-rate;
+};
+
+&sata {
+ status = "okay";
+};
+
+&usb2_phy1 {
+ phy-supply = <&ldousb_reg>;
+};
+
+&usb1 {
+ dr_mode = "host";
+ pinctrl-names = "default";
+ pinctrl-0 = <&usb1_pins>;
+};
--
1.7.9.5
--
Regards,
Nishanth Menon
More information about the linux-arm-kernel
mailing list