[PATCH 3/6] phy: Add driver to support individual USB PHYs on sun9i
Chen-Yu Tsai
wens at csie.org
Wed Nov 5 01:31:26 PST 2014
On Wed, Nov 5, 2014 at 1:03 AM, Maxime Ripard
<maxime.ripard at free-electrons.com> wrote:
> On Tue, Nov 04, 2014 at 12:07:16PM +0800, Chen-Yu Tsai wrote:
>> Unlike previous Allwinner SoCs, there is no central PHY control block
>> on the A80. Also, OTG support is completely split off into a different
>> controller.
>>
>> This adds a new driver to support the regular USB PHYs.
>>
>> Signed-off-by: Chen-Yu Tsai <wens at csie.org>
>> ---
>> .../devicetree/bindings/phy/sun9i-usb-phy.txt | 34 +++
>> drivers/phy/Kconfig | 12 ++
>> drivers/phy/Makefile | 1 +
>> drivers/phy/phy-sun9i-usb.c | 227 +++++++++++++++++++++
>> 4 files changed, 274 insertions(+)
>> create mode 100644 Documentation/devicetree/bindings/phy/sun9i-usb-phy.txt
>> create mode 100644 drivers/phy/phy-sun9i-usb.c
>>
>> diff --git a/Documentation/devicetree/bindings/phy/sun9i-usb-phy.txt b/Documentation/devicetree/bindings/phy/sun9i-usb-phy.txt
>> new file mode 100644
>> index 0000000..27a6067
>> --- /dev/null
>> +++ b/Documentation/devicetree/bindings/phy/sun9i-usb-phy.txt
>> @@ -0,0 +1,34 @@
>> +Allwinner sun9i USB PHY
>> +-----------------------
>> +
>> +Required properties:
>> +- compatible : should be one of
>> + * allwinner,sun9i-a80-usb-phy
>> +- reg : a list of offset + length pairs
>> +- #phy-cells : from the generic phy bindings, must be 0
>> +- clocks : phandle + clock specifier for the phy clocks
>> +- clock-names :
>> + * "phy" for normal USB
>> + * "hsic_480M", "hsic_12M" for HSIC
>
> Do you need all of them? phy and one of the hsic one?
It would be either "phy" or the hsic ones, depending on the
value of the "phy_type" property. I will make it clearer.
>> +- resets : a list of phandle + reset specifier pairs
>> +- reset-names :
>> + * "phy" for normal USB
>> + * "hsic" for HSIC
>> +- phy_type : "hsic" for HSIC usage;
>> + other values or absence of this property indicates normal USB
>> +
>> +It is recommended to list all clocks and resets available.
>> +The driver will only use those matching the phy_type.
>> +
>> +Example:
>> + usbphy1: phy at 00a01800 {
>> + compatible = "allwinner,sun9i-a80-usb-phy";
>> + reg = <0x00a01800 0x4>;
>> + clocks = <&usb_phy_clk 2>, <&usb_phy_clk 10>,
>> + <&usb_phy_clk 3>;
>> + clock-names = "hsic_480M", "hsic_12M", "phy";
>> + resets = <&usb_phy_clk 18>, <&usb_phy_clk 19>;
>> + reset-names = "hsic", "phy";
>> + status = "disabled";
>> + #phy-cells = <0>;
>> + };
>> diff --git a/drivers/phy/Kconfig b/drivers/phy/Kconfig
>> index 2a436e6..f5b7fbb 100644
>> --- a/drivers/phy/Kconfig
>> +++ b/drivers/phy/Kconfig
>> @@ -153,6 +153,18 @@ config PHY_SUN4I_USB
>> This driver controls the entire USB PHY block, both the USB OTG
>> parts, as well as the 2 regular USB 2 host PHYs.
>>
>> +config PHY_SUN9I_USB
>> + tristate "Allwinner sun9i SoC USB PHY driver"
>> + depends on ARCH_SUNXI && HAS_IOMEM && OF
>> + depends on RESET_CONTROLLER
>> + select USB_PHY
>> + select GENERIC_PHY
>> + help
>> + Enable this to support the transceiver that is part of Allwinner
>> + sun9i SoCs.
>> +
>> + This driver controls each individual USB 2 host PHY.
>> +
>> config PHY_SAMSUNG_USB2
>> tristate "Samsung USB 2.0 PHY driver"
>> depends on HAS_IOMEM
>> diff --git a/drivers/phy/Makefile b/drivers/phy/Makefile
>> index c4590fc..c3977dc 100644
>> --- a/drivers/phy/Makefile
>> +++ b/drivers/phy/Makefile
>> @@ -17,6 +17,7 @@ obj-$(CONFIG_TWL4030_USB) += phy-twl4030-usb.o
>> obj-$(CONFIG_PHY_EXYNOS5250_SATA) += phy-exynos5250-sata.o
>> obj-$(CONFIG_PHY_HIX5HD2_SATA) += phy-hix5hd2-sata.o
>> obj-$(CONFIG_PHY_SUN4I_USB) += phy-sun4i-usb.o
>> +obj-$(CONFIG_PHY_SUN9I_USB) += phy-sun9i-usb.o
>> obj-$(CONFIG_PHY_SAMSUNG_USB2) += phy-exynos-usb2.o
>> phy-exynos-usb2-y += phy-samsung-usb2.o
>> phy-exynos-usb2-$(CONFIG_PHY_EXYNOS4210_USB2) += phy-exynos4210-usb2.o
>> diff --git a/drivers/phy/phy-sun9i-usb.c b/drivers/phy/phy-sun9i-usb.c
>> new file mode 100644
>> index 0000000..f9085d9
>> --- /dev/null
>> +++ b/drivers/phy/phy-sun9i-usb.c
>> @@ -0,0 +1,227 @@
>> +/*
>> + * Allwinner sun9i USB phy driver
>> + *
>> + * Copyright (C) 2014 Chen-Yu Tsai <wens at csie.org>
>> + *
>> + * Based on phy-sun9i.c from
>
> I doubt this is the file you were thinking of :)
This is what happens when you do a global replace. :|
>> + * Hans de Goede <hdegoede at redhat.com>
>> + *
>> + * and code from
>> + * Allwinner Technology Co., Ltd. <www.allwinnertech.com>
>> + *
>> + * This program is free software; you can redistribute it and/or modify
>> + * it under the terms of the GNU General Public License as published by
>> + * the Free Software Foundation; either version 2 of the License, or
>> + * (at your option) any later version.
>> + *
>> + * This program is distributed in the hope that it will be useful,
>> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
>> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
>> + * GNU General Public License for more details.
>> + */
>> +
>> +#include <linux/clk.h>
>> +#include <linux/err.h>
>> +#include <linux/io.h>
>> +#include <linux/kernel.h>
>> +#include <linux/module.h>
>> +#include <linux/mutex.h>
>> +#include <linux/of.h>
>> +#include <linux/of_address.h>
>> +#include <linux/phy/phy.h>
>> +#include <linux/usb/of.h>
>> +#include <linux/platform_device.h>
>> +#include <linux/reset.h>
>> +
>> +#define SUNXI_AHB_ICHR8_EN BIT(10)
>> +#define SUNXI_AHB_INCR4_BURST_EN BIT(9)
>> +#define SUNXI_AHB_INCRX_ALIGN_EN BIT(8)
>> +#define SUNXI_ULPI_BYPASS_EN BIT(0)
>> +
>> +struct sun9i_usb_phy {
>> + struct phy *phy;
>> + void __iomem *pmu;
>> + struct regulator *vbus;
>> + struct reset_control *reset;
>> + struct clk *clk;
>> + struct clk *hsic_clk;
>> +};
>> +
>> +static void sun9i_usb_phy_passby(struct sun9i_usb_phy *phy, int enable)
>> +{
>> + u32 bits, reg_value;
>> +
>> + bits = SUNXI_AHB_ICHR8_EN | SUNXI_AHB_INCR4_BURST_EN |
>> + SUNXI_AHB_INCRX_ALIGN_EN | SUNXI_ULPI_BYPASS_EN;
>> +
>> + reg_value = readl(phy->pmu);
>> +
>> + if (enable)
>> + reg_value |= bits;
>> + else
>> + reg_value &= ~bits;
>> +
>> + writel(reg_value, phy->pmu);
>> +}
>> +
>> +static int sun9i_usb_phy_init(struct phy *_phy)
>> +{
>> + struct sun9i_usb_phy *phy = phy_get_drvdata(_phy);
>> + int ret;
>> +
>> + ret = clk_prepare_enable(phy->clk);
>> + if (ret)
>> + return ret;
>> +
>> + if (phy->hsic_clk) {
>> + ret = clk_prepare_enable(phy->hsic_clk);
>> + if (ret) {
>> + clk_disable_unprepare(phy->clk);
>> + return ret;
>> + }
>> + }
>> +
>> + ret = reset_control_deassert(phy->reset);
>> + if (ret) {
>> + if (phy->hsic_clk)
>> + clk_disable_unprepare(phy->hsic_clk);
>> + clk_disable_unprepare(phy->clk);
>> + return ret;
>
> Gotos in your exit path please.
I will try to clean it up more.
>> + }
>> +
>> + sun9i_usb_phy_passby(phy, 1);
>> +
>> + return 0;
>> +}
>> +
>> +static int sun9i_usb_phy_exit(struct phy *_phy)
>> +{
>> + struct sun9i_usb_phy *phy = phy_get_drvdata(_phy);
>> +
>> + sun9i_usb_phy_passby(phy, 0);
>> + reset_control_assert(phy->reset);
>> + if (phy->hsic_clk)
>> + clk_disable_unprepare(phy->hsic_clk);
>> + clk_disable_unprepare(phy->clk);
>> +
>> + return 0;
>> +}
>> +
>> +static int sun9i_usb_phy_power_on(struct phy *_phy)
>> +{
>> + struct sun9i_usb_phy *phy = phy_get_drvdata(_phy);
>> + int ret = 0;
>> +
>> + if (phy->vbus)
>> + ret = regulator_enable(phy->vbus);
>> +
>> + return ret;
>> +}
>> +
>> +static int sun9i_usb_phy_power_off(struct phy *_phy)
>> +{
>> + struct sun9i_usb_phy *phy = phy_get_drvdata(_phy);
>> +
>> + if (phy->vbus)
>> + regulator_disable(phy->vbus);
>> +
>> + return 0;
>> +}
>> +
>> +static struct phy_ops sun9i_usb_phy_ops = {
>> + .init = sun9i_usb_phy_init,
>> + .exit = sun9i_usb_phy_exit,
>> + .power_on = sun9i_usb_phy_power_on,
>> + .power_off = sun9i_usb_phy_power_off,
>> + .owner = THIS_MODULE,
>> +};
>> +
>> +static int sun9i_usb_phy_probe(struct platform_device *pdev)
>> +{
>> + struct sun9i_usb_phy *phy;
>> + struct device *dev = &pdev->dev;
>> + struct device_node *np = dev->of_node;
>> + struct phy_provider *phy_provider;
>> + struct resource *res;
>> + enum usb_phy_interface phy_type;
>> +
>> + phy = devm_kzalloc(dev, sizeof(*phy), GFP_KERNEL);
>> + if (!phy)
>> + return -ENOMEM;
>> +
>> + phy->vbus = devm_regulator_get_optional(dev, "vbus");
>> + if (IS_ERR(phy->vbus)) {
>> + if (PTR_ERR(phy->vbus) == -EPROBE_DEFER)
>> + return -EPROBE_DEFER;
>> + phy->vbus = NULL;
>> + }
>> +
>> + phy_type = of_usb_get_phy_mode(np);
>> + if (phy_type == USBPHY_INTERFACE_MODE_HSIC) {
>> + phy->clk = devm_clk_get(dev, "hsic_480M");
>> + if (IS_ERR(phy->clk)) {
>> + dev_err(dev, "failed to get hsic_480M clock\n");
>> + return PTR_ERR(phy->clk);
>> + }
>> +
>> + phy->hsic_clk = devm_clk_get(dev, "hsic_12M");
>> + if (IS_ERR(phy->clk)) {
>> + dev_err(dev, "failed to get hsic_12M clock\n");
>> + return PTR_ERR(phy->clk);
>> + }
>> +
>> + phy->reset = devm_reset_control_get(dev, "hsic");
>> + if (IS_ERR(phy->reset)) {
>> + dev_err(dev, "failed to get reset control\n");
>> + return PTR_ERR(phy->reset);
>> + }
>> + } else {
>> + phy->clk = devm_clk_get(dev, "phy");
>> + if (IS_ERR(phy->clk)) {
>> + dev_err(dev, "failed to get phy clock\n");
>> + return PTR_ERR(phy->clk);
>> + }
>> +
>> + phy->reset = devm_reset_control_get(dev, "phy");
>> + if (IS_ERR(phy->reset)) {
>> + dev_err(dev, "failed to get reset control\n");
>> + return PTR_ERR(phy->reset);
>> + }
>> + }
>> +
>> + res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
>> + phy->pmu = devm_ioremap_resource(dev, res);
>> + if (IS_ERR(phy->pmu))
>> + return PTR_ERR(phy->pmu);
>> +
>> + phy->phy = devm_phy_create(dev, NULL, &sun9i_usb_phy_ops, NULL);
>> + if (IS_ERR(phy->phy)) {
>> + dev_err(dev, "failed to create PHY\n");
>> + return PTR_ERR(phy->phy);
>> + }
>> +
>> + phy_set_drvdata(phy->phy, phy);
>> + dev_set_drvdata(dev, phy);
>> + phy_provider = devm_of_phy_provider_register(dev, of_phy_simple_xlate);
>> +
>> + return PTR_ERR_OR_ZERO(phy_provider);
>> +}
>> +
>> +static const struct of_device_id sun9i_usb_phy_of_match[] = {
>> + { .compatible = "allwinner,sun9i-a80-usb-phy" },
>> + { },
>> +};
>> +MODULE_DEVICE_TABLE(of, sun9i_usb_phy_of_match);
>> +
>> +static struct platform_driver sun9i_usb_phy_driver = {
>> + .probe = sun9i_usb_phy_probe,
>> + .driver = {
>> + .of_match_table = sun9i_usb_phy_of_match,
>> + .name = "sun9i-usb-phy",
>> + }
>> +};
>> +module_platform_driver(sun9i_usb_phy_driver);
>> +
>> +MODULE_DESCRIPTION("Allwinner sun9i USB phy driver");
>> +MODULE_AUTHOR("Chen-Yu Tsai <wens at csie.org>");
>> +MODULE_LICENSE("GPL v2");
>
> Thanks!
> Maxime
Thanks for the review.
ChenYu
More information about the linux-arm-kernel
mailing list