[PATCH v8 2/3] [media] rc: add sunxi-ir driver
Maxime Ripard
maxime.ripard at free-electrons.com
Fri May 30 01:25:27 PDT 2014
On Mon, May 26, 2014 at 04:26:44AM +0600, Alexander Bersenev wrote:
> This patch adds driver for sunxi IR controller.
> It is based on Alexsey Shestacov's work based on the original driver
> supplied by Allwinner.
>
> Signed-off-by: Alexander Bersenev <bay at hackerdom.ru>
> Signed-off-by: Alexsey Shestacov <wingrime at linux-sunxi.org>
> ---
> drivers/media/rc/Kconfig | 10 ++
> drivers/media/rc/Makefile | 1 +
> drivers/media/rc/sunxi-cir.c | 313 +++++++++++++++++++++++++++++++++++++++++++
> 3 files changed, 324 insertions(+)
> create mode 100644 drivers/media/rc/sunxi-cir.c
>
> diff --git a/drivers/media/rc/Kconfig b/drivers/media/rc/Kconfig
> index 8fbd377..9427fad 100644
> --- a/drivers/media/rc/Kconfig
> +++ b/drivers/media/rc/Kconfig
> @@ -343,4 +343,14 @@ config RC_ST
>
> If you're not sure, select N here.
>
> +config IR_SUNXI
> + tristate "SUNXI IR remote control"
> + depends on RC_CORE
> + depends on ARCH_SUNXI
> + ---help---
> + Say Y if you want to use sunXi internal IR Controller
> +
> + To compile this driver as a module, choose M here: the module will
> + be called sunxi-ir.
> +
> endif #RC_DEVICES
> diff --git a/drivers/media/rc/Makefile b/drivers/media/rc/Makefile
> index f8b54ff..9ee9ee7 100644
> --- a/drivers/media/rc/Makefile
> +++ b/drivers/media/rc/Makefile
> @@ -32,4 +32,5 @@ obj-$(CONFIG_IR_GPIO_CIR) += gpio-ir-recv.o
> obj-$(CONFIG_IR_IGUANA) += iguanair.o
> obj-$(CONFIG_IR_TTUSBIR) += ttusbir.o
> obj-$(CONFIG_RC_ST) += st_rc.o
> +obj-$(CONFIG_IR_SUNXI) += sunxi-cir.o
> obj-$(CONFIG_IR_IMG) += img-ir/
> diff --git a/drivers/media/rc/sunxi-cir.c b/drivers/media/rc/sunxi-cir.c
> new file mode 100644
> index 0000000..245d8dc
> --- /dev/null
> +++ b/drivers/media/rc/sunxi-cir.c
> @@ -0,0 +1,313 @@
> +/*
> + * Driver for Allwinner sunXi IR controller
> + *
> + * Copyright (C) 2014 Alexsey Shestacov <wingrime at linux-sunxi.org>
> + * Copyright (C) 2014 Alexander Bersenev <bay at hackerdom.ru>
> + *
> + * Based on sun5i-ir.c:
> + * Copyright (C) 2007-2012 Daniel Wang
> + * Allwinner Technology Co., Ltd. <www.allwinnertech.com>
> + *
> + * This program is free software; you can redistribute it and/or
> + * modify it under the terms of the GNU General Public License as
> + * published by the Free Software Foundation; either version 2 of
> + * the License, or (at your option) any later version.
> + *
> + * This program is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + */
> +
> +#include <linux/clk.h>
> +#include <linux/interrupt.h>
> +#include <linux/module.h>
> +#include <linux/of_platform.h>
> +#include <media/rc-core.h>
> +
> +#define SUNXI_IR_DEV "sunxi-ir"
> +
> +/* Registers */
> +/* IR Control */
> +#define SUNXI_IR_CTL_REG 0x00
> +#define REG_CTL_GEN BIT(0) /* Global Enable */
> +#define REG_CTL_RXEN BIT(1) /* RX block enable */
> +#define REG_CTL_MD (BIT(4)|BIT(5)) /* CIR mode */
You should have a space around the operator here, and one more level
of indentation for the bits definition would be nice.
> +
> +/* Rx Config */
> +#define SUNXI_IR_RXCTL_REG 0x10
> +#define REG_RXCTL_RPPI BIT(2) /* Pulse Polarity Invert flag */
> +
> +/* Rx Data */
> +#define SUNXI_IR_RXFIFO_REG 0x20
> +
> +/* Rx Interrupt Enable */
> +#define SUNXI_IR_RXINT_REG 0x2C
> +#define REG_RXINT_ROI_EN BIT(0) /* Rx FIFO Overflow */
> +#define REG_RXINT_RPEI_EN BIT(1) /* Rx Packet End */
> +#define REG_RXINT_RAI_EN BIT(4) /* Rx FIFO Data Available */
> +/* Rx FIFO available byte level */
Either put the comments on the same line or on the above line, but
please stick to the choice you're making
> +#define REG_RXINT_RAL(val) (((val) << 8) & (BIT(8)|BIT(9)|BIT(10)|BIT(11)))
Just use the mask directly here, or the GENMASK macro.
> +
> +/* Rx Interrupt Status */
> +#define SUNXI_IR_RXSTA_REG 0x30
> +/* RX FIFO Get Available Counter */
> +#define REG_RXSTA_GET_AC(val) (((val) >> 8) & (BIT(0)|BIT(1)|BIT(2)|BIT(3) \
> + |BIT(4)|BIT(5)))
> +/* Clear all interrupt status value */
> +#define REG_RXSTA_CLEARALL 0xff
> +
> +/* IR Sample Config */
> +#define SUNXI_IR_CIR_REG 0x34
> +/* CIR_REG register noise threshold */
> +#define REG_CIR_NTHR(val) (((val) << 2) & (BIT(2)|BIT(3)|BIT(4)|BIT(5) \
> + |BIT(6)|BIT(7)))
> +/* CIR_REG register idle threshold */
> +#define REG_CIR_ITHR(val) (((val) << 8) & (BIT(8)|BIT(9)|BIT(10)|BIT(11) \
> + |BIT(12)|BIT(13)|BIT(14)|BIT(15)))
> +
> +/* Hardware supported fifo size */
> +#define SUNXI_IR_FIFO_SIZE 16
> +/* How many messages in FIFO trigger IRQ */
> +#define TRIGGER_LEVEL 8
> +/* Required frequency for IR0 or IR1 clock in CIR mode */
> +#define SUNXI_IR_BASE_CLK 8000000
> +/* Frequency after IR internal divider */
> +#define SUNXI_IR_CLK (SUNXI_IR_BASE_CLK / 64)
> +/* Sample period in ns */
> +#define SUNXI_IR_SAMPLE (1000000000ul / SUNXI_IR_CLK)
> +/* Noise threshold in samples */
> +#define SUNXI_IR_RXNOISE 1
> +/* Idle Threshold in samples */
> +#define SUNXI_IR_RXIDLE 20
> +/* Time after which device stops sending data in ms */
> +#define SUNXI_IR_TIMEOUT 120
> +
> +struct sunxi_ir {
> + spinlock_t ir_lock;
> + struct rc_dev *rc;
> + void __iomem *base;
> + int irq;
> + struct clk *clk;
> + struct clk *apb_clk;
> + const char *map_name;
> +};
> +
> +static irqreturn_t sunxi_ir_irq(int irqno, void *dev_id)
> +{
> + unsigned long status;
> + unsigned char dt;
> + unsigned int cnt, rc;
> + struct sunxi_ir *ir = dev_id;
> + DEFINE_IR_RAW_EVENT(rawir);
> +
> + spin_lock(&ir->ir_lock);
> +
> + status = readl(ir->base + SUNXI_IR_RXSTA_REG);
> +
> + /* clean all pending statuses */
> + writel(status | REG_RXSTA_CLEARALL, ir->base + SUNXI_IR_RXSTA_REG);
> +
> + if (status & REG_RXINT_RAI_EN) {
> + /* How many messages in fifo */
> + rc = REG_RXSTA_GET_AC(status);
> + /* Sanity check */
> + rc = rc > SUNXI_IR_FIFO_SIZE ? SUNXI_IR_FIFO_SIZE : rc;
> + /* If we have data */
> + for (cnt = 0; cnt < rc; cnt++) {
> + /* for each bit in fifo */
> + dt = readb(ir->base + SUNXI_IR_RXFIFO_REG);
> + rawir.pulse = (dt & 0x80) != 0;
> + rawir.duration = ((dt & 0x7f) + 1) * SUNXI_IR_SAMPLE;
> + ir_raw_event_store_with_filter(ir->rc, &rawir);
> + }
> + }
> +
> + if (status & REG_RXINT_ROI_EN) {
> + ir_raw_event_reset(ir->rc);
> + } else if (status & REG_RXINT_RPEI_EN) {
> + ir_raw_event_set_idle(ir->rc, true);
> + ir_raw_event_handle(ir->rc);
> + }
> +
> + spin_unlock(&ir->ir_lock);
> +
> + return IRQ_HANDLED;
> +}
> +
> +
> +static int sunxi_ir_probe(struct platform_device *pdev)
> +{
> + int ret = 0;
> + unsigned long tmp = 0;
> +
> + struct device *dev = &pdev->dev;
> + struct device_node *dn = dev->of_node;
> + struct resource *res;
> + struct sunxi_ir *ir;
> +
> + ir = devm_kzalloc(dev, sizeof(struct sunxi_ir), GFP_KERNEL);
> + if (!ir)
> + return -ENOMEM;
> +
> + /* Clock */
> + ir->apb_clk = devm_clk_get(dev, "apb");
> + if (IS_ERR(ir->apb_clk)) {
> + dev_err(dev, "failed to get a apb clock.\n");
> + return PTR_ERR(ir->apb_clk);
> + }
Newline.
> + ir->clk = devm_clk_get(dev, "ir");
> + if (IS_ERR(ir->clk)) {
> + dev_err(dev, "failed to get a ir clock.\n");
> + return PTR_ERR(ir->clk);
> + }
> +
> + ret = clk_set_rate(ir->clk, SUNXI_IR_BASE_CLK);
> + if (ret) {
> + dev_err(dev, "set ir base clock failed!\n");
> + return ret;
> + }
> +
> + if (clk_prepare_enable(ir->apb_clk)) {
> + dev_err(dev, "try to enable apb_ir_clk failed\n");
> + return -EINVAL;
> + }
> +
> + if (clk_prepare_enable(ir->clk)) {
> + dev_err(dev, "try to enable ir_clk failed\n");
> + ret = -EINVAL;
> + goto exit_clkdisable_apb_clk;
> + }
> +
> + /* IO */
> + res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> +
You can drop the extra line here
> + ir->base = devm_ioremap_resource(dev, res);
> + if (IS_ERR(ir->base)) {
> + dev_err(dev, "failed to map registers\n");
> + ret = PTR_ERR(ir->base);
> + goto exit_clkdisable_clk;
> + }
> +
> + ir->rc = rc_allocate_device();
> + if (!ir->rc) {
> + dev_err(dev, "failed to allocate device\n");
> + ret = -ENOMEM;
> + goto exit_clkdisable_clk;
> + }
> +
> + ir->rc->priv = ir;
> + ir->rc->input_name = SUNXI_IR_DEV;
> + ir->rc->input_phys = "sunxi-ir/input0";
> + ir->rc->input_id.bustype = BUS_HOST;
> + ir->rc->input_id.vendor = 0x0001;
> + ir->rc->input_id.product = 0x0001;
> + ir->rc->input_id.version = 0x0100;
> + ir->map_name = of_get_property(dn, "linux,rc-map-name", NULL);
> + ir->rc->map_name = ir->map_name ?: RC_MAP_EMPTY;
> + ir->rc->dev.parent = dev;
> + ir->rc->driver_type = RC_DRIVER_IR_RAW;
> + rc_set_allowed_protocols(ir->rc, RC_BIT_ALL);
> + ir->rc->rx_resolution = SUNXI_IR_SAMPLE;
> + ir->rc->timeout = MS_TO_NS(SUNXI_IR_TIMEOUT);
> + ir->rc->driver_name = SUNXI_IR_DEV;
> +
> + ret = rc_register_device(ir->rc);
> + if (ret) {
> + dev_err(dev, "failed to register rc device\n");
> + goto exit_free_dev;
> + }
> +
> + platform_set_drvdata(pdev, ir);
> +
> + /* IRQ */
> + ir->irq = platform_get_irq(pdev, 0);
> + if (ir->irq < 0) {
> + dev_err(dev, "no irq resource\n");
> + ret = ir->irq;
> + goto exit_free_dev;
> + }
> +
> + ret = devm_request_irq(dev, ir->irq, sunxi_ir_irq, 0, SUNXI_IR_DEV, ir);
> + if (ret) {
> + dev_err(dev, "failed request irq\n");
> + goto exit_free_dev;
> + }
> +
> + /* Enable CIR Mode */
> + writel(REG_CTL_MD, ir->base+SUNXI_IR_CTL_REG);
> +
> + /* Set noise threshold and idle threshold */
> + writel(REG_CIR_NTHR(SUNXI_IR_RXNOISE)|REG_CIR_ITHR(SUNXI_IR_RXIDLE),
> + ir->base + SUNXI_IR_CIR_REG);
> +
> + /* Invert Input Signal */
> + writel(REG_RXCTL_RPPI, ir->base + SUNXI_IR_RXCTL_REG);
> +
> + /* Clear All Rx Interrupt Status */
> + writel(REG_RXSTA_CLEARALL, ir->base + SUNXI_IR_RXSTA_REG);
> +
> + /* Enable IRQ on overflow, packet end, FIFO available with trigger
> + level */
Multi-line comments should be
/*
* Like
* this
*/
> + writel(REG_RXINT_ROI_EN | REG_RXINT_RPEI_EN |
> + REG_RXINT_RAI_EN | REG_RXINT_RAL(TRIGGER_LEVEL - 1),
> + ir->base + SUNXI_IR_RXINT_REG);
> +
> + /* Enable IR Module */
> + tmp = readl(ir->base + SUNXI_IR_CTL_REG);
> + writel(tmp | REG_CTL_GEN | REG_CTL_RXEN, ir->base + SUNXI_IR_CTL_REG);
> +
> + dev_info(dev, "initialized sunXi IR driver\n");
> + return 0;
> +
> +exit_free_dev:
> + rc_free_device(ir->rc);
> +exit_clkdisable_clk:
> + clk_disable_unprepare(ir->clk);
> +exit_clkdisable_apb_clk:
> + clk_disable_unprepare(ir->apb_clk);
> +
> + return ret;
> +}
> +
> +static int sunxi_ir_remove(struct platform_device *pdev)
> +{
> + unsigned long flags;
> + struct sunxi_ir *ir = platform_get_drvdata(pdev);
> +
> + clk_disable_unprepare(ir->clk);
> + clk_disable_unprepare(ir->apb_clk);
> +
> + spin_lock_irqsave(&ir->ir_lock, flags);
> + /* disable IR IRQ */
> + writel(0, ir->base + SUNXI_IR_RXINT_REG);
> + /* clear All Rx Interrupt Status */
> + writel(REG_RXSTA_CLEARALL, ir->base + SUNXI_IR_RXSTA_REG);
> + /* disable IR */
> + writel(0, ir->base + SUNXI_IR_CTL_REG);
> + spin_unlock_irqrestore(&ir->ir_lock, flags);
> +
> + rc_unregister_device(ir->rc);
> + return 0;
> +}
> +
> +static const struct of_device_id sunxi_ir_match[] = {
> + { .compatible = "allwinner,sun7i-a20-ir", },
> + {},
> +};
> +
> +static struct platform_driver sunxi_ir_driver = {
> + .probe = sunxi_ir_probe,
> + .remove = sunxi_ir_remove,
> + .driver = {
> + .name = SUNXI_IR_DEV,
> + .owner = THIS_MODULE,
> + .of_match_table = sunxi_ir_match,
> + },
> +};
> +
> +module_platform_driver(sunxi_ir_driver);
> +
> +MODULE_DESCRIPTION("Allwinner sunXi IR controller driver");
> +MODULE_AUTHOR("Alexsey Shestacov <wingrime at linux-sunxi.org>");
> +MODULE_LICENSE("GPL");
> --
> 1.9.3
>
Thanks!
Maxime
--
Maxime Ripard, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 819 bytes
Desc: Digital signature
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20140530/564066b4/attachment.sig>
More information about the linux-arm-kernel
mailing list