[PATCH 09/11] brcmfmac: Fix OOB interrupt not working for BCM43362

[Arend van Spriel]

On 05/27/14 23:28, Hans de Goede wrote:
> Hi,
>
> On 05/27/2014 07:03 PM, Arend van Spriel wrote:
>> On 05/26/14 09:48, Hans de Goede wrote:
>>> It has taken me a long long time to get the OOB interrupt working on the
>>> AP6210 sdio wifi/bt module found on various Allwinner A20 boards. In the
>>> end I found these magic register pokes in the cubietruck kernel tree:
>>> https://github.com/cubieboard2/linux-sunxi/commit/7f08ba395617d17e7a711507503d89a50406fe7a
>>>
>>>
>>> I'm not entirely sure if this specific to the AP6210 module, or if this
>>> should be done for all BCM43362 sdio devices.
>>
>> Let keep it as this for now. I added some remarks below.
>>
>> Regards,
>> Arend
>>
>>> Signed-off-by: Hans de Goede<hdegoede at redhat.com>
>>> ---
>>> drivers/net/wireless/brcm80211/brcmfmac/bcmsdh.c | 18 ++++++++++++++++++
>>> 1 file changed, 18 insertions(+)
>>>
>>> diff --git a/drivers/net/wireless/brcm80211/brcmfmac/bcmsdh.c
>>> b/drivers/net/wireless/brcm80211/brcmfmac/bcmsdh.c
>>> index 0fc707c..2369a0f 100644
>>> --- a/drivers/net/wireless/brcm80211/brcmfmac/bcmsdh.c
>>> +++ b/drivers/net/wireless/brcm80211/brcmfmac/bcmsdh.c
>>> @@ -39,7 +39,9 @@
>>> #include<brcm_hw_ids.h>
>>> #include<brcmu_utils.h>
>>> #include<brcmu_wifi.h>
>>> +#include<chipcommon.h>
>>> #include<soc.h>
>>> +#include "chip.h"
>>> #include "dhd_bus.h"
>>> #include "dhd_dbg.h"
>>> #include "sdio_host.h"
>>> @@ -119,6 +121,7 @@ int brcmf_sdiod_intr_register(struct
>>> brcmf_sdio_dev *sdiodev)
>>> {
>>> int ret = 0;
>>> u8 data;
>>> + u32 addr, gpiocontrol;
>>> unsigned long flags;
>>>
>>> if ((sdiodev->pdata)&& (sdiodev->pdata->oob_irq_supported)) {
>>> @@ -148,6 +151,21 @@ int brcmf_sdiod_intr_register(struct
>>> brcmf_sdio_dev *sdiodev)
>>>
>>> sdio_claim_host(sdiodev->func[1]);
>>>
>>> + if (sdiodev->bus_if->chip == BCM43362_CHIP_ID) {
>> + /* assign GPIO to SDIO core */
>>> + addr = CORE_CC_REG(SI_ENUM_BASE, gpiocontrol);
>>> + gpiocontrol = brcmf_sdiod_regrl(sdiodev, addr,&ret);
>>> + gpiocontrol |= 0x2;
>>> + brcmf_sdiod_regwl(sdiodev, addr, gpiocontrol,&ret);
>>> +
>>> + /* SPROM_ADDR_HIGH ? perhaps the defines name is off */
>>
>> These names are all off. These should be:
>> SBSDIO_SPROM_ADDR_HIGH = SBSDIO_GPIO_SELECT
>> SBSDIO_CHIP_CTRL_DATA = SBSDIO_GPIO_OUT
>> SBSDIO_CHIP_CTRL_EN = SBSDIO_GPIO_EN
>
> Ok, so I guess I should do a pre-patch adding defines for these, should
> these replace the existing defines for these addresses in:
> drivers/net/wireless/brcm80211/brcmfmac/sdio_host.h
>
> Or should the pre-patch add defines with the new names and keep the old
> ones ?

These defines are not used in the code so go ahead and replace them. It 
needs some more cleanup, but I can do a subsequent patch for that.

Gr. AvS