[PATCH v2] ARM: shmobile: r8a7790: link PCI USB devices to USB PHY

[Sergei Shtylyov]

Hello.

On 05/27/2014 02:36 AM, Magnus Damm wrote:

>> Describe the PCI USB devices that are behind the PCI bridges, adding necessary
>> links to the USB PHY device.

>> Based on the original work by Ben Dooks <ben.dooks at codethink.co.uk>.

>> Signed-off-by: Sergei Shtylyov <sergei.shtylyov at cogentembedded.com>

>> ---
>> This patch is against 'renesas-devel-v3.15-rc7-20140526' tag of Simon Horman's
>> 'renesas.git' repo plus R8A7790/Lager PCI and USB PHY support patches posted
>> before. The patch requires the internal PCI DT support, USB PHY driver, and
>> USB HCD generic PHY support (also already posted) in order to work.

>> Changes in version 2:
>> - renamed the PCI OHCI/EHCI device nodes to comply with the PCI binding;
>> - changed the PHY specifier in the PCI#2 node to reflect that channel #1 support
>>    was dropped;
>> - resolved rejects, refreshed the patch.

>>   arch/arm/boot/dts/r8a7790.dtsi |   28 ++++++++++++++++++++++++++++
>>   1 file changed, 28 insertions(+)

>> Index: renesas/arch/arm/boot/dts/r8a7790.dtsi
>> ===================================================================
>> --- renesas.orig/arch/arm/boot/dts/r8a7790.dtsi
>> +++ renesas/arch/arm/boot/dts/r8a7790.dtsi
>> @@ -919,6 +919,20 @@
>>                  interrupt-map = <0x0000 0 0 1 &gic 0 108 IRQ_TYPE_LEVEL_HIGH
>>                                   0x0800 0 0 1 &gic 0 108 IRQ_TYPE_LEVEL_HIGH
>>                                   0x1000 0 0 2 &gic 0 108 IRQ_TYPE_LEVEL_HIGH>;
>> +
>> +               usb at 0,1 {
>> +                       reg = <0x800 0 0 0 0>;
>> +                       device_type = "pci";
>> +                       phys = <&usbphy 0 0>;
>> +                       phy-names = "usb";
>> +               };
>> +
>> +               usb at 0,2 {
>> +                       reg = <0x1000 0 0 0 0>;
>> +                       device_type = "pci";
>> +                       phys = <&usbphy 0 0>;
>> +                       phy-names = "usb";
>> +               };
>>          };
>>
>>          pci1: pci at ee0b0000 {
>> @@ -955,5 +969,19 @@
>>                  interrupt-map = <0x0000 0 0 1 &gic 0 113 IRQ_TYPE_LEVEL_HIGH
>>                                   0x0800 0 0 1 &gic 0 113 IRQ_TYPE_LEVEL_HIGH
>>                                   0x1000 0 0 2 &gic 0 113 IRQ_TYPE_LEVEL_HIGH>;
>> +
>> +               usb at 0,1 {
>> +                       reg = <0x800 0 0 0 0>;
>> +                       device_type = "pci";
>> +                       phys = <&usbphy 1 0>;
>> +                       phy-names = "usb";
>> +               };
>> +
>> +               usb at 0,2 {
>> +                       reg = <0x1000 0 0 0 0>;
>> +                       device_type = "pci";
>> +                       phys = <&usbphy 1 0>;
>> +                       phy-names = "usb";
>> +               };
>>          };
>>   };

> Hi Sergei,

> Above I see two hunks of DTS code but my r8a7790 data sheet contains
> three USB PCI devices. Perhaps my understanding is wrong, or may there

    You probably wanted to say 6 (OHCI and EHCI are 2 different PCI devices).

> is some other patch available to enable all USB PCI devices included
> in the SoC?

    This patch doesn't enable USB devices, it just links them to the PHY where 
it makes sense (for USB channel #1 it doesn't).

> Thanks,
> / magnus

WBR, Sergei