[PATCH 09/11] brcmfmac: Fix OOB interrupt not working for BCM43362

[Arend van Spriel]

On 05/26/14 09:48, Hans de Goede wrote:
> It has taken me a long long time to get the OOB interrupt working on the
> AP6210 sdio wifi/bt module found on various Allwinner A20 boards. In the
> end I found these magic register pokes in the cubietruck kernel tree:
> https://github.com/cubieboard2/linux-sunxi/commit/7f08ba395617d17e7a711507503d89a50406fe7a
>
> I'm not entirely sure if this specific to the AP6210 module, or if this
> should be done for all BCM43362 sdio devices.

This magic is not in our host drivers so my guess is that it is board 
specific. This means the nvram file provided to the firmware should have 
this specified. Can you send me yours?

Regards,
Arend

> Signed-off-by: Hans de Goede<hdegoede at redhat.com>
> ---
>   drivers/net/wireless/brcm80211/brcmfmac/bcmsdh.c | 18 ++++++++++++++++++
>   1 file changed, 18 insertions(+)
>
> diff --git a/drivers/net/wireless/brcm80211/brcmfmac/bcmsdh.c b/drivers/net/wireless/brcm80211/brcmfmac/bcmsdh.c
> index 0fc707c..2369a0f 100644
> --- a/drivers/net/wireless/brcm80211/brcmfmac/bcmsdh.c
> +++ b/drivers/net/wireless/brcm80211/brcmfmac/bcmsdh.c
> @@ -39,7 +39,9 @@
>   #include<brcm_hw_ids.h>
>   #include<brcmu_utils.h>
>   #include<brcmu_wifi.h>
> +#include<chipcommon.h>
>   #include<soc.h>
> +#include "chip.h"
>   #include "dhd_bus.h"
>   #include "dhd_dbg.h"
>   #include "sdio_host.h"
> @@ -119,6 +121,7 @@ int brcmf_sdiod_intr_register(struct brcmf_sdio_dev *sdiodev)
>   {
>   	int ret = 0;
>   	u8 data;
> +	u32 addr, gpiocontrol;
>   	unsigned long flags;
>
>   	if ((sdiodev->pdata)&&  (sdiodev->pdata->oob_irq_supported)) {
> @@ -148,6 +151,21 @@ int brcmf_sdiod_intr_register(struct brcmf_sdio_dev *sdiodev)
>
>   		sdio_claim_host(sdiodev->func[1]);
>
> +		if (sdiodev->bus_if->chip == BCM43362_CHIP_ID) {
> +			addr = CORE_CC_REG(SI_ENUM_BASE, gpiocontrol);
> +			gpiocontrol = brcmf_sdiod_regrl(sdiodev, addr,&ret);
> +			gpiocontrol |= 0x2;
> +			brcmf_sdiod_regwl(sdiodev, addr, gpiocontrol,&ret);
> +
> +			/* SPROM_ADDR_HIGH ? perhaps the defines name is off */
> +			brcmf_sdiod_regwb(sdiodev, SBSDIO_SPROM_ADDR_HIGH, 0xf,
> +					&ret);
> +			brcmf_sdiod_regwb(sdiodev, SBSDIO_CHIP_CTRL_DATA, 0,
> +					&ret);
> +			brcmf_sdiod_regwb(sdiodev, SBSDIO_CHIP_CTRL_EN, 0x2,
> +					&ret);
> +		}
> +
>   		/* must configure SDIO_CCCR_IENx to enable irq */
>   		data = brcmf_sdiod_regrb(sdiodev, SDIO_CCCR_IENx,&ret);
>   		data |= 1<<  SDIO_FUNC_1 | 1<<  SDIO_FUNC_2 | 1;