[PATCH 21/22] ARM: sunxi: Add Allwinner A23 dtsi
Maxime Ripard
maxime.ripard at free-electrons.com
Sun May 25 12:38:45 PDT 2014
On Fri, May 23, 2014 at 03:51:24PM +0800, Chen-Yu Tsai wrote:
> The Allwinner A23 is a tablet oriented SoC with 2 Cortex-A7 cores
> and a Mali-400MP2 GPU.
>
> Signed-off-by: Chen-Yu Tsai <wens at csie.org>
> ---
> arch/arm/boot/dts/sun8i-a23.dtsi | 524 +++++++++++++++++++++++++++++++++++++++
> 1 file changed, 524 insertions(+)
> create mode 100644 arch/arm/boot/dts/sun8i-a23.dtsi
>
> diff --git a/arch/arm/boot/dts/sun8i-a23.dtsi b/arch/arm/boot/dts/sun8i-a23.dtsi
> new file mode 100644
> index 0000000..1cff087
> --- /dev/null
> +++ b/arch/arm/boot/dts/sun8i-a23.dtsi
> @@ -0,0 +1,524 @@
> +/*
> + * Copyright 2014 Chen-Yu Tsai
> + *
> + * Chen-Yu Tsai <wens at csie.org>
> + *
> + * The code contained herein is licensed under the GNU General Public
> + * License. You may obtain a copy of the GNU General Public License
> + * Version 2 or later at the following locations:
> + *
> + * http://www.opensource.org/licenses/gpl-license.html
> + * http://www.gnu.org/copyleft/gpl.html
> + */
> +
> +/include/ "skeleton.dtsi"
> +
> +/ {
> + interrupt-parent = <&gic>;
> +
> + aliases {
> + serial0 = &uart0;
> + serial1 = &uart1;
> + serial2 = &uart2;
> + serial3 = &uart3;
> + serial4 = &uart4;
> + serial5 = &r_uart;
> + };
> +
> +
> + cpus {
> + enable-method = "allwinner,sun8i-a23";
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + cpu at 0 {
> + compatible = "arm,cortex-a7";
> + device_type = "cpu";
> + reg = <0>;
> + clocks = <&cpu>;
> + };
> +
> + cpu at 1 {
> + compatible = "arm,cortex-a7";
> + device_type = "cpu";
> + reg = <1>;
> + clocks = <&cpu>;
The clocks attributes have not been merged yet.
> + };
> + };
> +
> + memory {
> + reg = <0x40000000 0x80000000>;
> + };
> +
> + pmu {
> + compatible = "arm,cortex-a7-pmu", "arm,cortex-a15-pmu";
> + interrupts = <0 120 4>,
> + <0 121 4>,
> + <0 122 4>,
> + <0 123 4>;
> + };
The PMU usually have as much interrupts as CPU core, so this is most
likely wrong.
Also, do you know if the arch timers are usable on the A23?
> +
> + clocks {
> + #address-cells = <1>;
> + #size-cells = <1>;
> + ranges;
> +
> + osc24M: osc24M_clk {
> + #clock-cells = <0>;
> + compatible = "fixed-clock";
> + clock-frequency = <24000000>;
> + clock-output-names = "osc24M";
> + };
> +
> + osc32k: osc32k_clk {
> + #clock-cells = <0>;
> + compatible = "fixed-clock";
> + clock-frequency = <32768>;
> + clock-output-names = "osc32k";
> + };
> +
> + pll1: clk at 01c20000 {
> + #clock-cells = <0>;
> + compatible = "allwinner,sun8i-a23-pll1-clk";
> + reg = <0x01c20000 0x4>;
> + clocks = <&osc24M>;
> + clock-output-names = "pll1";
> + };
> +
> + pll6: clk at 01c20028 {
> + #clock-cells = <1>;
> + compatible = "allwinner,sun6i-a31-pll6-clk";
> + reg = <0x01c20028 0x4>;
> + clocks = <&osc24M>;
> + clock-output-names = "pll6_other", "pll6";
> + };
> +
> + cpu: cpu_clk at 01c20050 {
> + #clock-cells = <0>;
> + compatible = "allwinner,sun4i-a10-cpu-clk";
> + reg = <0x01c20050 0x4>;
> +
> + /*
> + * PLL1 is listed twice here.
> + * While it looks suspicious, it's actually documented
> + * that way both in the datasheet and in the code from
> + * Allwinner.
> + */
> + clocks = <&osc32k>, <&osc24M>, <&pll1>, <&pll1>;
> + clock-output-names = "cpu";
> + };
> +
> + axi: axi_clk at 01c20050 {
> + #clock-cells = <0>;
> + /*
> + * AXI clock on A23 is actually wider,
> + * but extra bit is useless for divider
> + */
Then please add a new compatible for this, even though we're not doing
anything differently (yet).
> + compatible = "allwinner,sun4i-a10-axi-clk";
> + reg = <0x01c20050 0x4>;
> + clocks = <&cpu>;
> + clock-output-names = "axi";
> + };
> +
> + ahb1_pll6: ahb1_pll6_clk at 01c20054 {
> + #clock-cells = <0>;
> + compatible = "allwinner,sun6i-a31-ahb1-pll6-clk";
> + reg = <0x01c20054 0x4>;
> + clocks = <&pll6 0>;
> + clock-output-names = "ahb1_pll6";
> + };
> +
> + ahb1_mux: ahb1_mux_clk at 01c20054 {
> + #clock-cells = <0>;
> + compatible = "allwinner,sun6i-a31-ahb1-mux-clk";
> + reg = <0x01c20054 0x4>;
> + clocks = <&osc32k>, <&osc24M>, <&axi>, <&ahb1_pll6>;
> + clock-output-names = "ahb1_mux";
> + };
> +
> + ahb1: ahb1_clk at 01c20054 {
> + #clock-cells = <0>;
> + compatible = "allwinner,sun4i-a10-ahb-clk";
> + reg = <0x01c20054 0x4>;
> + clocks = <&ahb1_mux>;
> + clock-output-names = "ahb1";
> + };
> +
> + ahb1_gates: clk at 01c20060 {
> + #clock-cells = <1>;
> + compatible = "allwinner,sun8i-a23-ahb1-gates-clk";
> + reg = <0x01c20060 0x8>;
> + clocks = <&ahb1>;
> + clock-output-names = "ahb1_mipidsi", "ahb1_dma",
> + "ahb1_mmc0", "ahb1_mmc1", "ahb1_mmc2",
> + "ahb1_nand", "ahb1_sdram",
> + "ahb1_hstimer", "ahb1_spi0",
> + "ahb1_spi1", "ahb1_otg", "ahb1_ehci",
> + "ahb1_ohci", "ahb1_ve", "ahb1_lcd",
> + "ahb1_csi", "ahb1_be", "ahb1_fe",
> + "ahb1_gpu", "ahb1_spinlock",
> + "ahb1_drc";
> + };
> +
> + apb1: apb1_clk at 01c20054 {
> + #clock-cells = <0>;
> + compatible = "allwinner,sun4i-a10-apb0-clk";
> + reg = <0x01c20054 0x4>;
> + clocks = <&ahb1>;
> + clock-output-names = "apb1";
> + };
> +
> + apb1_gates: clk at 01c20068 {
> + #clock-cells = <1>;
> + compatible = "allwinner,sun8i-a23-apb1-gates-clk";
> + reg = <0x01c20068 0x4>;
> + clocks = <&apb1>;
> + clock-output-names = "apb1_codec", "apb1_pio",
> + "apb1_daudio0", "apb1_daudio1";
> + };
> +
> + apb2_mux: apb2_mux at 01c20058 {
> + #clock-cells = <0>;
> + compatible = "allwinner,sun4i-a10-apb1-mux-clk";
> + reg = <0x01c20058 0x4>;
> + clocks = <&osc32k>, <&osc24M>, <&pll6 0>, <&pll6 0>;
> + clock-output-names = "apb2_mux";
> + };
It doesn't look to be ordered by physical address.
> + apb2: apb2 at 01c20058 {
> + #clock-cells = <0>;
> + compatible = "allwinner,sun6i-a31-apb2-div-clk";
> + reg = <0x01c20058 0x4>;
> + clocks = <&apb2_mux>;
> + clock-output-names = "apb2";
> + };
> +
> + apb2_gates: clk at 01c2006c {
> + #clock-cells = <1>;
> + compatible = "allwinner,sun8i-a23-apb2-gates-clk";
> + reg = <0x01c2006c 0x4>;
> + clocks = <&apb2>;
> + clock-output-names = "apb2_i2c0", "apb2_i2c1",
> + "apb2_i2c2", "apb2_uart0",
> + "apb2_uart1", "apb2_uart2",
> + "apb2_uart3", "apb2_uart4";
> + };
> +
> + mmc0_clk: clk at 01c20088 {
> + #clock-cells = <0>;
> + compatible = "allwinner,sun4i-a10-mod0-clk";
> + reg = <0x01c20088 0x4>;
> + clocks = <&osc24M>, <&pll6 0>;
> + clock-output-names = "mmc0";
> + };
> +
> + mmc1_clk: clk at 01c2008c {
> + #clock-cells = <0>;
> + compatible = "allwinner,sun4i-a10-mod0-clk";
> + reg = <0x01c2008c 0x4>;
> + clocks = <&osc24M>, <&pll6 0>;
> + clock-output-names = "mmc1";
> + };
> +
> + mmc2_clk: clk at 01c20090 {
> + #clock-cells = <0>;
> + compatible = "allwinner,sun4i-a10-mod0-clk";
> + reg = <0x01c20090 0x4>;
> + clocks = <&osc24M>, <&pll6 0>;
> + clock-output-names = "mmc2";
> + };
> +
> + spi0_clk: clk at 01c200a0 {
> + #clock-cells = <0>;
> + compatible = "allwinner,sun4i-a10-mod0-clk";
> + reg = <0x01c200a0 0x4>;
> + clocks = <&osc24M>, <&pll6 0>;
> + clock-output-names = "spi0";
> + };
> +
> + spi1_clk: clk at 01c200a4 {
> + #clock-cells = <0>;
> + compatible = "allwinner,sun4i-a10-mod0-clk";
> + reg = <0x01c200a4 0x4>;
> + clocks = <&osc24M>, <&pll6 0>;
> + clock-output-names = "spi1";
> + };
> + };
> +
> + soc at 01c00000 {
> + compatible = "simple-bus";
> + #address-cells = <1>;
> + #size-cells = <1>;
> + ranges;
> +
> + pio: pinctrl at 01c20800 {
> + compatible = "allwinner,sun8i-a23-pinctrl";
> + reg = <0x01c20800 0x400>;
> + interrupts = <0 11 4>,
> + <0 15 4>,
> + <0 17 4>;
> + clocks = <&apb1_gates 5>;
> + gpio-controller;
> + interrupt-controller;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + #gpio-cells = <3>;
> +
> + uart0_pins_a: uart0 at 0 {
> + allwinner,pins = "PF2", "PF4";
> + allwinner,function = "uart0";
> + allwinner,drive = <0>;
> + allwinner,pull = <0>;
> + };
> +
> + i2c0_pins_a: i2c0 at 0 {
> + allwinner,pins = "PH2", "PH3";
> + allwinner,function = "i2c0";
> + allwinner,drive = <0>;
> + allwinner,pull = <0>;
> + };
> +
> + i2c1_pins_a: i2c1 at 0 {
> + allwinner,pins = "PH4", "PH5";
> + allwinner,function = "i2c1";
> + allwinner,drive = <0>;
> + allwinner,pull = <0>;
> + };
> + };
> +
> + ahb1_rst: reset at 01c202c0 {
> + #reset-cells = <1>;
> + compatible = "allwinner,sun6i-a31-ahb1-reset";
> + reg = <0x01c202c0 0xc>;
> + };
> +
> + apb1_rst: reset at 01c202d0 {
> + #reset-cells = <1>;
> + compatible = "allwinner,sun6i-a31-clock-reset";
> + reg = <0x01c202d0 0x4>;
> + };
> +
> + apb2_rst: reset at 01c202d8 {
> + #reset-cells = <1>;
> + compatible = "allwinner,sun6i-a31-clock-reset";
> + reg = <0x01c202d8 0x4>;
> + };
> +
> + timer at 01c20c00 {
> + compatible = "allwinner,sun4i-a10-timer";
> + reg = <0x01c20c00 0xa0>;
> + interrupts = <0 18 4>,
> + <0 19 4>;
> + clocks = <&osc24M>;
> + };
> +
> + wdt0: watchdog at 01c20ca0 {
> + compatible = "allwinner,sun6i-a31-wdt";
> + reg = <0x01c20ca0 0x20>;
> + interrupts = <0 25 4>;
> + };
> +
> + uart0: serial at 01c28000 {
> + compatible = "snps,dw-apb-uart";
> + reg = <0x01c28000 0x400>;
> + interrupts = <0 0 4>;
> + reg-shift = <2>;
> + reg-io-width = <4>;
> + clocks = <&apb2_gates 16>;
> + resets = <&apb2_rst 16>;
> + status = "disabled";
> + };
> +
> + uart1: serial at 01c28400 {
> + compatible = "snps,dw-apb-uart";
> + reg = <0x01c28400 0x400>;
> + interrupts = <0 1 4>;
> + reg-shift = <2>;
> + reg-io-width = <4>;
> + clocks = <&apb2_gates 17>;
> + resets = <&apb2_rst 17>;
> + status = "disabled";
> + };
> +
> + uart2: serial at 01c28800 {
> + compatible = "snps,dw-apb-uart";
> + reg = <0x01c28800 0x400>;
> + interrupts = <0 2 4>;
> + reg-shift = <2>;
> + reg-io-width = <4>;
> + clocks = <&apb2_gates 18>;
> + resets = <&apb2_rst 18>;
> + status = "disabled";
> + };
> +
> + uart3: serial at 01c28c00 {
> + compatible = "snps,dw-apb-uart";
> + reg = <0x01c28c00 0x400>;
> + interrupts = <0 3 4>;
> + reg-shift = <2>;
> + reg-io-width = <4>;
> + clocks = <&apb2_gates 19>;
> + resets = <&apb2_rst 19>;
> + status = "disabled";
> + };
> +
> + uart4: serial at 01c29000 {
> + compatible = "snps,dw-apb-uart";
> + reg = <0x01c29000 0x400>;
> + interrupts = <0 4 4>;
> + reg-shift = <2>;
> + reg-io-width = <4>;
> + clocks = <&apb2_gates 20>;
> + resets = <&apb2_rst 20>;
> + status = "disabled";
> + };
> +
> + i2c0: i2c at 01c2ac00 {
> + compatible = "allwinner,sun6i-a31-i2c";
> + reg = <0x01c2ac00 0x400>;
> + interrupts = <0 6 4>;
> + clocks = <&apb2_gates 0>;
> + clock-frequency = <100000>;
> + resets = <&apb2_rst 0>;
> + status = "disabled";
> + };
> +
> + i2c1: i2c at 01c2b000 {
> + compatible = "allwinner,sun6i-a31-i2c";
> + reg = <0x01c2b000 0x400>;
> + interrupts = <0 7 4>;
> + clocks = <&apb2_gates 1>;
> + clock-frequency = <100000>;
> + resets = <&apb2_rst 1>;
> + status = "disabled";
> + };
> +
> + i2c2: i2c at 01c2b400 {
> + compatible = "allwinner,sun6i-a31-i2c";
> + reg = <0x01c2b400 0x400>;
> + interrupts = <0 8 4>;
> + clocks = <&apb2_gates 2>;
> + clock-frequency = <100000>;
> + resets = <&apb2_rst 2>;
> + status = "disabled";
> + };
> +
> + spi0: spi at 01c68000 {
> + compatible = "allwinner,sun6i-a31-spi";
> + reg = <0x01c68000 0x1000>;
> + interrupts = <0 65 4>;
> + clocks = <&ahb1_gates 20>, <&spi0_clk>;
> + clock-names = "ahb", "mod";
> + resets = <&ahb1_rst 20>;
> + status = "disabled";
> + };
> +
> + spi1: spi at 01c69000 {
> + compatible = "allwinner,sun6i-a31-spi";
> + reg = <0x01c69000 0x1000>;
> + interrupts = <0 66 4>;
> + clocks = <&ahb1_gates 21>, <&spi1_clk>;
> + clock-names = "ahb", "mod";
> + resets = <&ahb1_rst 21>;
> + status = "disabled";
> + };
> +
> + gic: interrupt-controller at 01c81000 {
> + compatible = "arm,cortex-a7-gic", "arm,cortex-a15-gic";
> + reg = <0x01c81000 0x1000>,
> + <0x01c82000 0x1000>;
> + interrupt-controller;
> + #interrupt-cells = <3>;
> + };
> +
> + nmi_intc: interrupt-controller at 01f00c0c {
> + compatible = "allwinner,sun6i-a31-sc-nmi";
> + interrupt-controller;
> + #interrupt-cells = <2>;
> + reg = <0x01f00c0c 0x38>;
> + interrupts = <0 32 4>;
> + };
> +
> + prcm at 01f01400 {
> + compatible = "allwinner,sun8i-a23-prcm";
> + reg = <0x01f01400 0x200>;
> +
> + ar100: ar100_clk {
> + compatible = "fixed-factor-clock";
> + #clock-cells = <0>;
> + clock-div = <1>;
> + clock-mult = <1>;
> + clocks = <&osc24M>;
> + clock-output-names = "ar100";
> + };
> +
> + ahb0: ahb0_clk {
> + compatible = "fixed-factor-clock";
> + #clock-cells = <0>;
> + clock-div = <1>;
> + clock-mult = <1>;
> + clocks = <&ar100>;
> + clock-output-names = "ahb0";
> + };
> +
> + apb0: apb0_clk {
> + compatible = "allwinner,sun8i-a23-apb0-clk";
> + #clock-cells = <0>;
> + clocks = <&ahb0>;
> + clock-output-names = "apb0";
> + };
> +
> + apb0_gates: apb0_gates_clk {
> + compatible = "allwinner,sun6i-a31-apb0-gates-clk";
> + #clock-cells = <1>;
> + clocks = <&apb0>;
> + clock-indices = <0>, <2>, <3>, <4>, <6>;
> + clock-output-names = "apb0_pio", "apb0_timer",
> + "apb0_rsb", "apb0_uart",
> + "apb0_i2c";
> + };
> +
> + apb0_rst: apb0_rst {
> + compatible = "allwinner,sun6i-a31-clock-reset";
> + #reset-cells = <1>;
> + };
> + };
> +
> + cpucfg at 01f01c00 {
> + compatible = "allwinner,sun8i-a23-cpuconfig";
> + reg = <0x01f01c00 0x300>;
> + };
> +
> + r_uart: serial at 01f02800 {
> + compatible = "snps,dw-apb-uart";
> + reg = <0x01f02800 0x400>;
> + interrupts = <0 38 4>;
> + reg-shift = <2>;
> + reg-io-width = <4>;
> + clocks = <&apb0_gates 4>;
> + resets = <&apb0_rst 4>;
> + status = "disabled";
> + };
> +
> + r_pio: pinctrl at 01f02c00 {
> + compatible = "allwinner,sun8i-a23-r-pinctrl";
> + reg = <0x01f02c00 0x400>;
> + interrupts = <0 45 4>;
> + clocks = <&apb0_gates 0>;
> + resets = <&apb0_rst 0>;
> + gpio-controller;
> + interrupt-controller;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + #gpio-cells = <3>;
> +
> + r_uart_pins_a: r_uart at 0 {
> + allwinner,pins = "PL2", "PL3";
> + allwinner,function = "s_uart";
> + allwinner,drive = <0>;
> + allwinner,pull = <0>;
> + };
> +
> + };
> + };
> +};
Thanks,
Maxime
--
Maxime Ripard, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 819 bytes
Desc: Digital signature
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20140525/1130fc21/attachment.sig>
More information about the linux-arm-kernel
mailing list