[PATCH v4 1/2] arm64: adjust el0_sync so that a function can be called

[Larry Bassel]

On 23 May 14 15:44, Catalin Marinas wrote:
> On Thu, May 22, 2014 at 11:35:20PM +0100, Larry Bassel wrote:
> > > On 05/22/2014 03:27 PM, Larry Bassel wrote:
> > > > To implement the context tracker properly on arm64,
> > > > a function call needs to be made after debugging and
> > > > interrupts are turned on, but before the lr is changed
> > > > to point to ret_to_user(). If the function call
> > > > is made after the lr is changed the function will not
> > > > return to the correct place.
> > > > 
> > > > For similar reasons, defer the setting of x0 so that
> > > > it doesn't need to be saved around the function call
> > > > (save far_el1 in x26 temporarily instead).
> > > > 
> > > > Signed-off-by: Larry Bassel <larry.bassel at linaro.org>
> > > > ---
> > > >  arch/arm64/kernel/entry.S | 24 +++++++++++++++++-------
> > > >  1 file changed, 17 insertions(+), 7 deletions(-)
> > > > 
> > > > diff --git a/arch/arm64/kernel/entry.S b/arch/arm64/kernel/entry.S
> > > > index e8b23a3..20b336e 100644
> > > > --- a/arch/arm64/kernel/entry.S
> > > > +++ b/arch/arm64/kernel/entry.S
> > > > @@ -354,7 +354,6 @@ el0_sync:
> > > >  	lsr	x24, x25, #ESR_EL1_EC_SHIFT	// exception class
> > > >  	cmp	x24, #ESR_EL1_EC_SVC64		// SVC in 64-bit state
> > > >  	b.eq	el0_svc
> > > > -	adr	lr, ret_to_user
> > > >  	cmp	x24, #ESR_EL1_EC_DABT_EL0	// data abort in EL0
> > > >  	b.eq	el0_da
> > > >  	cmp	x24, #ESR_EL1_EC_IABT_EL0	// instruction abort in EL0
> > > > @@ -383,7 +382,6 @@ el0_sync_compat:
> > > >  	lsr	x24, x25, #ESR_EL1_EC_SHIFT	// exception class
> > > >  	cmp	x24, #ESR_EL1_EC_SVC32		// SVC in 32-bit state
> > > >  	b.eq	el0_svc_compat
> > > > -	adr	lr, ret_to_user
> > > >  	cmp	x24, #ESR_EL1_EC_DABT_EL0	// data abort in EL0
> > > >  	b.eq	el0_da
> > > >  	cmp	x24, #ESR_EL1_EC_IABT_EL0	// instruction abort in EL0
> > > > @@ -426,22 +424,26 @@ el0_da:
> > > >  	/*
> > > >  	 * Data abort handling
> > > >  	 */
> > > > -	mrs	x0, far_el1
> > > > -	bic	x0, x0, #(0xff << 56)
> > > > +	mrs	x26, far_el1
> > > >  	// enable interrupts before calling the main handler
> > > >  	enable_dbg_and_irq
> > > > +	mov	x0, x26
> > > > +	bic	x0, x0, #(0xff << 56)
> > > 
> > > Nit: I believe you can bit clear with x26 as the source register and omit the
> > > move instruction.
> > 
> > Is that really an improvement (assuming it works)? Are we saving
> > any cycles here? If so, does it matter? It is easy to see what
> > the move instruction is doing.
> 
> Even if it's not noticeable, I would still reduce the number of lines by
> one. BIC with immediate is just an alias for AND and it supports
> different source and destination.

Ack.

> 
> -- 
> Catalin

Larry