[PATCH 21/71] clocksource: sh_tmu: Use request_irq() instead of setup_irq()
Daniel Lezcano
daniel.lezcano at linaro.org
Fri May 23 03:31:01 PDT 2014
From: Laurent Pinchart <laurent.pinchart+renesas at ideasonboard.com>
The driver claims it needs to register an interrupt handler too early
for request_irq(). This might have been true in the past, but the only
meaningful difference between request_irq() and setup_irq() today is an
additional kzalloc() call in request_irq(). As the driver calls
kmalloc() itself we know that the slab allocator is available, we can
thus switch to request_irq().
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas at ideasonboard.com>
---
drivers/clocksource/sh_tmu.c | 22 ++++++++--------------
1 file changed, 8 insertions(+), 14 deletions(-)
diff --git a/drivers/clocksource/sh_tmu.c b/drivers/clocksource/sh_tmu.c
index ecd7b60..8613cc9 100644
--- a/drivers/clocksource/sh_tmu.c
+++ b/drivers/clocksource/sh_tmu.c
@@ -38,7 +38,7 @@
struct sh_tmu_priv {
void __iomem *mapbase;
struct clk *clk;
- struct irqaction irqaction;
+ int irq;
struct platform_device *pdev;
unsigned long rate;
unsigned long periodic;
@@ -401,10 +401,11 @@ static void sh_tmu_register_clockevent(struct sh_tmu_priv *p,
clockevents_config_and_register(ced, 1, 0x300, 0xffffffff);
- ret = setup_irq(p->irqaction.irq, &p->irqaction);
+ ret = request_irq(p->irq, sh_tmu_interrupt,
+ IRQF_TIMER | IRQF_IRQPOLL | IRQF_NOBALANCING,
+ dev_name(&p->pdev->dev), p);
if (ret) {
- dev_err(&p->pdev->dev, "failed to request irq %d\n",
- p->irqaction.irq);
+ dev_err(&p->pdev->dev, "failed to request irq %d\n", p->irq);
return;
}
}
@@ -425,7 +426,7 @@ static int sh_tmu_setup(struct sh_tmu_priv *p, struct platform_device *pdev)
{
struct sh_timer_config *cfg = pdev->dev.platform_data;
struct resource *res;
- int irq, ret;
+ int ret;
ret = -ENXIO;
memset(p, 0, sizeof(*p));
@@ -444,8 +445,8 @@ static int sh_tmu_setup(struct sh_tmu_priv *p, struct platform_device *pdev)
goto err0;
}
- irq = platform_get_irq(p->pdev, 0);
- if (irq < 0) {
+ p->irq = platform_get_irq(p->pdev, 0);
+ if (p->irq < 0) {
dev_err(&p->pdev->dev, "failed to get irq\n");
goto err0;
}
@@ -457,13 +458,6 @@ static int sh_tmu_setup(struct sh_tmu_priv *p, struct platform_device *pdev)
goto err0;
}
- /* setup data for setup_irq() (too early for request_irq()) */
- p->irqaction.name = dev_name(&p->pdev->dev);
- p->irqaction.handler = sh_tmu_interrupt;
- p->irqaction.dev_id = p;
- p->irqaction.irq = irq;
- p->irqaction.flags = IRQF_TIMER | IRQF_IRQPOLL | IRQF_NOBALANCING;
-
/* get hold of clock */
p->clk = clk_get(&p->pdev->dev, "tmu_fck");
if (IS_ERR(p->clk)) {
--
1.7.9.5
More information about the linux-arm-kernel
mailing list