[PATCH v2] ARM: realview: basic device tree implementation
jason at lakedaemon.net
Thu May 22 06:41:44 PDT 2014
On Fri, May 09, 2014 at 12:08:16AM +0200, Linus Walleij wrote:
> This implements basic device tree boot support for the RealView
> platforms, with a basic device tree for ARM PB1176 as an example.
> The implementation is done with a new DT-specific board file
> using only pre-existing bindings for the basic IRQ, timer and
> serial port drivers. A new compatible type is added to the GIC
> for the ARM1176.
> This implementation uses the MFD syscon handle from day one to
> access the system controller registers, and register the devices
> using the SoC bus.
> Cc: Arnd Bergmann <arnd at arndb.de>
> Cc: Rob Herring <robh at kernel.org>
> Signed-off-by: Linus Walleij <linus.walleij at linaro.org>
> ChangeLog v1->v2:
> - Adjust timer clock names to be the same as the example in the
> device tree binding.
> - Remove all memory fixup code - this should be handled by the
> device tree specification of memory areas or by special MM hacks
> for the RealView PBX.
> - Fix the documentation around syscon to specify that it can be in
> any node, need not be the root node.
> - Switch device tree license to the BSD license, taken from
> - Add a hunk for the new compatible string to
> - Move the clocks out of the SoC node, certainly the xtal is not
> sitting on the SoC...
> - Sort the selects in Kconfig alphabetically
> - Use IS_ENABLED() for the l2x0 code snippet
> - Instead of checking the board variant in the reset routine to
> figure out how to tweak the reset controller, have a compatible
> string for each syscon variant, map it to an enum that provides a
> unique type ID and that way figure out how to handle it in a maybe
> more elegant way.
> - Open issue: what do to with the l2x0 stuff?
> Documentation/devicetree/bindings/arm/arm-boards | 57 ++++++
> Documentation/devicetree/bindings/arm/gic.txt | 1 +
> arch/arm/boot/dts/Makefile | 1 +
> arch/arm/boot/dts/arm-realview-pb1176.dts | 177 ++++++++++++++++++
> arch/arm/mach-realview/Kconfig | 10 +
> arch/arm/mach-realview/Makefile | 1 +
> arch/arm/mach-realview/realview-dt.c | 225 +++++++++++++++++++++++
> arch/arm/mm/Kconfig | 2 +-
> drivers/irqchip/irq-gic.c | 1 +
> 9 files changed, 474 insertions(+), 1 deletion(-)
> create mode 100644 arch/arm/boot/dts/arm-realview-pb1176.dts
> create mode 100644 arch/arm/mach-realview/realview-dt.c
> diff --git a/Documentation/devicetree/bindings/arm/gic.txt b/Documentation/devicetree/bindings/arm/gic.txt
> index 5573c08d3180..539420194efd 100644
> --- a/Documentation/devicetree/bindings/arm/gic.txt
> +++ b/Documentation/devicetree/bindings/arm/gic.txt
> @@ -16,6 +16,7 @@ Main node required properties:
> + "arm,arm1176jzf-gic"
> - interrupt-controller : Identifies the node as an interrupt controller
> - #interrupt-cells : Specifies the number of cells needed to encode an
> interrupt source. The type shall be a <u32> and the value shall be 3.
> diff --git a/drivers/irqchip/irq-gic.c b/drivers/irqchip/irq-gic.c
> index 57d165e026f4..70281b38c73b 100644
> --- a/drivers/irqchip/irq-gic.c
> +++ b/drivers/irqchip/irq-gic.c
> @@ -1073,6 +1073,7 @@ gic_of_init(struct device_node *node, struct device_node *parent)
> IRQCHIP_DECLARE(cortex_a15_gic, "arm,cortex-a15-gic", gic_of_init);
> IRQCHIP_DECLARE(cortex_a9_gic, "arm,cortex-a9-gic", gic_of_init);
> +IRQCHIP_DECLARE(arm1176jzf_gic, "arm,arm1176jzf-gic", gic_of_init);
> IRQCHIP_DECLARE(msm_8660_qgic, "qcom,msm-8660-qgic", gic_of_init);
> IRQCHIP_DECLARE(msm_qgic2, "qcom,msm-qgic2", gic_of_init);
Please place in alphabetical order. We're starting to collect
compatible strings for this driver...
Acked-by: Jason Cooper <jason at lakedaemon.net>
More information about the linux-arm-kernel