[Patch v4 2/5] Power: reset: add bindings for keystone reset driver

[Ivan Khoronzhuk]

On 05/21/2014 05:50 PM, Arnd Bergmann wrote:
> On Wednesday 21 May 2014 17:27:31 Ivan Khoronzhuk wrote:
>> This node is intended to allow SoC reset in case of software reset
>> or appropriate watchdogs.
>>
>> The Keystone SoCs can contain up to 4 watchdog timers to reset
>> SoC. Each watchdog timer event input is connected to the Reset Mux
>> block. The Reset Mux block can be configured to cause reset or not.
>>
>> Additionally soft or hard reset can be configured.
>>
>> Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk at ti.com>
>> ---
>>   .../bindings/power/reset/keystone-reset.txt        | 66 ++++++++++++++++++++++
>>   1 file changed, 66 insertions(+)
>>   create mode 100644 Documentation/devicetree/bindings/power/reset/keystone-reset.txt
>>
>> diff --git a/Documentation/devicetree/bindings/power/reset/keystone-reset.txt b/Documentation/devicetree/bindings/power/reset/keystone-reset.txt
>> new file mode 100644
>> index 0000000..64cb7b4
>> --- /dev/null
>> +++ b/Documentation/devicetree/bindings/power/reset/keystone-reset.txt
>> @@ -0,0 +1,66 @@
>> +* Device tree bindings for Texas Instruments keystone reset
>> +
>> +This node is intended to allow SoC reset in case of software reset
>> +of selected watchdogs.
>> +
>> +The Keystone SoCs can contain up to 4 watchdog timers to reset
>> +SoC. Each watchdog timer event input is connected to the Reset Mux
>> +block. The Reset Mux block can be configured to cause reset or not.
>> +
>> +Additionally soft or hard reset can be configured.
>> +
>> +Required properties:
>> +
>> +- compatible:		ti,keystone-reset
>> +
>> +- ti,syscon-pll:	syscon register range used to access pll controller
>> +			registers in order to use reset control registers.
>> +
>> +- ti,syscon-dev:	syscon register range used to access device state
>> +			control registers in order to use mux block registers
>> +			for all watchdogs.
> This should be updated to call these phandles rather than register ranges.
>
>> +Optional properties:
>> +
>> +- ti,soft-reset:	Boolean option indicating soft reset.
>> +			By default hard reset is used.
>> +
>> +- ti,wdt_list:		WDT list that can cause SoC reset. It's not related
>> +			to WDT driver, it's just needed to enable a SoC related
>> +			reset that's triggered by one of WDTs. The list is
>> +			in format: <0>, <2>; It can be in random order and
>> +			begins from 0 to 3, as keystone can contain up to 4 SoC
>> +			reset watchdogs and can be in random order.
>> +
>> +Example 1:
>> +Setup keystone reset so that in case software reset or
>> +WDT0 is triggered it issues hard reset for SoC.
>> +
>> +pllctrl: pll_controller {
>> +	compatible = "syscon";
>> +	reg = <0x2310000 0x200>;
>> +};
>> +
>> +devctrl: device_state_control {
>> +	compatible = "syscon";
>> +	reg = <0x2620000 0x1000>;
>> +};
> It's ok to have these in the example, but please also add a binding file
> for each one describing what they are, and add a proper "compatible" string
> so they can be matched by a high-level device driver if needed.
>
> This could for instance be
>
> 	compatible = "ti,keystone-1.0-pll-controller", "syscon";

Arnd,

I've slightly confused where should I add these bindings.
The main pll controller mostly used by clk driver....
As its register set is used also by reset driver it's logically to put 
it to bindings/mfd,
but pll controller in mfd it's strange....

Could you please help to decide where should it be?.

-- 
Regards,
Ivan Khoronzhuk