[PATCH RESEND v2 3/4] regulator: bcm590xx: add support for regulators on secondary I2C slave
Matt Porter
mporter at linaro.org
Tue May 20 13:28:05 PDT 2014
The bcm590xx MFD driver now exposes a secondary regmap descriptor
making the registers for regulators on the secondary I2C slave address
available. Add support for GPLDO1-6 and VBUS regulators found within
this register range.
Signed-off-by: Matt Porter <mporter at linaro.org>
Acked-by: Mark Brown <broonie at linaro.org>
---
drivers/regulator/bcm590xx-regulator.c | 92 ++++++++++++++++++++++++++++++----
1 file changed, 82 insertions(+), 10 deletions(-)
diff --git a/drivers/regulator/bcm590xx-regulator.c b/drivers/regulator/bcm590xx-regulator.c
index c3750c5..57544e2 100644
--- a/drivers/regulator/bcm590xx-regulator.c
+++ b/drivers/regulator/bcm590xx-regulator.c
@@ -22,7 +22,7 @@
#include <linux/regulator/of_regulator.h>
#include <linux/slab.h>
-/* Register defs */
+/* I2C slave 0 registers */
#define BCM590XX_RFLDOPMCTRL1 0x60
#define BCM590XX_IOSR1PMCTRL1 0x7a
#define BCM590XX_IOSR2PMCTRL1 0x7c
@@ -31,13 +31,34 @@
#define BCM590XX_SDSR2PMCTRL1 0x86
#define BCM590XX_MSRPMCTRL1 0x8a
#define BCM590XX_VSRPMCTRL1 0x8e
-#define BCM590XX_REG_ENABLE BIT(7)
-
#define BCM590XX_RFLDOCTRL 0x96
#define BCM590XX_CSRVOUT1 0xc0
+
+/* I2C slave 1 registers */
+#define BCM590XX_GPLDO5PMCTRL1 0x16
+#define BCM590XX_GPLDO6PMCTRL1 0x18
+#define BCM590XX_GPLDO1CTRL 0x1a
+#define BCM590XX_GPLDO2CTRL 0x1b
+#define BCM590XX_GPLDO3CTRL 0x1c
+#define BCM590XX_GPLDO4CTRL 0x1d
+#define BCM590XX_GPLDO5CTRL 0x1e
+#define BCM590XX_GPLDO6CTRL 0x1f
+#define BCM590XX_OTG_CTRL 0x40
+#define BCM590XX_GPLDO1PMCTRL1 0x57
+#define BCM590XX_GPLDO2PMCTRL1 0x59
+#define BCM590XX_GPLDO3PMCTRL1 0x5b
+#define BCM590XX_GPLDO4PMCTRL1 0x5d
+
+#define BCM590XX_REG_ENABLE BIT(7)
+#define BCM590XX_VBUS_ENABLE BIT(2)
#define BCM590XX_LDO_VSEL_MASK GENMASK(5, 3)
#define BCM590XX_SR_VSEL_MASK GENMASK(5, 0)
+/*
+ * RFLDO to VSR regulators are
+ * accessed via I2C slave 0
+ */
+
/* LDO regulator IDs */
#define BCM590XX_REG_RFLDO 0
#define BCM590XX_REG_CAMLDO1 1
@@ -62,9 +83,25 @@
#define BCM590XX_REG_SDSR2 18
#define BCM590XX_REG_VSR 19
-#define BCM590XX_NUM_REGS 20
+/*
+ * GPLDO1 to VBUS regulators are
+ * accessed via I2C slave 1
+ */
+
+#define BCM590XX_REG_GPLDO1 20
+#define BCM590XX_REG_GPLDO2 21
+#define BCM590XX_REG_GPLDO3 22
+#define BCM590XX_REG_GPLDO4 23
+#define BCM590XX_REG_GPLDO5 24
+#define BCM590XX_REG_GPLDO6 25
+#define BCM590XX_REG_VBUS 26
+
+#define BCM590XX_NUM_REGS 27
#define BCM590XX_REG_IS_LDO(n) (n < BCM590XX_REG_CSR)
+#define BCM590XX_REG_IS_GPLDO(n) \
+ ((n > BCM590XX_REG_VSR) && (n < BCM590XX_REG_VBUS))
+#define BCM590XX_REG_IS_VBUS(n) (n == BCM590XX_REG_VBUS)
struct bcm590xx_board {
struct regulator_init_data *bcm590xx_pmu_init_data[BCM590XX_NUM_REGS];
@@ -149,6 +186,12 @@ static struct bcm590xx_info bcm590xx_regs[] = {
BCM590XX_REG_RANGES(sdsr1, dcdc_sdsr1_ranges),
BCM590XX_REG_RANGES(sdsr2, dcdc_iosr1_ranges),
BCM590XX_REG_RANGES(vsr, dcdc_iosr1_ranges),
+ BCM590XX_REG_TABLE(gpldo1, ldo_a_table),
+ BCM590XX_REG_TABLE(gpldo2, ldo_a_table),
+ BCM590XX_REG_TABLE(gpldo3, ldo_a_table),
+ BCM590XX_REG_TABLE(gpldo4, ldo_a_table),
+ BCM590XX_REG_TABLE(gpldo5, ldo_a_table),
+ BCM590XX_REG_TABLE(gpldo6, ldo_a_table),
};
struct bcm590xx_reg {
@@ -161,6 +204,8 @@ static int bcm590xx_get_vsel_register(int id)
{
if (BCM590XX_REG_IS_LDO(id))
return BCM590XX_RFLDOCTRL + id;
+ else if (BCM590XX_REG_IS_GPLDO(id))
+ return BCM590XX_GPLDO1CTRL + id;
else
return BCM590XX_CSRVOUT1 + (id - BCM590XX_REG_CSR) * 3;
}
@@ -171,6 +216,8 @@ static int bcm590xx_get_enable_register(int id)
if (BCM590XX_REG_IS_LDO(id))
reg = BCM590XX_RFLDOPMCTRL1 + id * 2;
+ else if (BCM590XX_REG_IS_GPLDO(id))
+ reg = BCM590XX_GPLDO1PMCTRL1 + id * 2;
else
switch (id) {
case BCM590XX_REG_CSR:
@@ -191,8 +238,11 @@ static int bcm590xx_get_enable_register(int id)
case BCM590XX_REG_SDSR2:
reg = BCM590XX_SDSR2PMCTRL1;
break;
+ case BCM590XX_REG_VBUS:
+ reg = BCM590XX_OTG_CTRL;
};
+
return reg;
}
@@ -216,6 +266,12 @@ static struct regulator_ops bcm590xx_ops_dcdc = {
.map_voltage = regulator_map_voltage_linear_range,
};
+static struct regulator_ops bcm590xx_ops_vbus = {
+ .is_enabled = regulator_is_enabled_regmap,
+ .enable = regulator_enable_regmap,
+ .disable = regulator_disable_regmap,
+};
+
#define BCM590XX_MATCH(_name, _id) \
{ \
.name = #_name, \
@@ -243,6 +299,13 @@ static struct of_regulator_match bcm590xx_matches[] = {
BCM590XX_MATCH(sdsr1, SDSR1),
BCM590XX_MATCH(sdsr2, SDSR2),
BCM590XX_MATCH(vsr, VSR),
+ BCM590XX_MATCH(gpldo1, GPLDO1),
+ BCM590XX_MATCH(gpldo2, GPLDO2),
+ BCM590XX_MATCH(gpldo3, GPLDO3),
+ BCM590XX_MATCH(gpldo4, GPLDO4),
+ BCM590XX_MATCH(gpldo5, GPLDO5),
+ BCM590XX_MATCH(gpldo6, GPLDO6),
+ BCM590XX_MATCH(vbus, VBUS),
};
static struct bcm590xx_board *bcm590xx_parse_dt_reg_data(
@@ -353,17 +416,23 @@ static int bcm590xx_probe(struct platform_device *pdev)
pmu->desc[i].linear_ranges = info->linear_ranges;
pmu->desc[i].n_linear_ranges = info->n_linear_ranges;
- if (BCM590XX_REG_IS_LDO(i)) {
+ if ((BCM590XX_REG_IS_LDO(i)) || (BCM590XX_REG_IS_GPLDO(i))) {
pmu->desc[i].ops = &bcm590xx_ops_ldo;
pmu->desc[i].vsel_mask = BCM590XX_LDO_VSEL_MASK;
- } else {
+ } else if (BCM590XX_REG_IS_VBUS(i))
+ pmu->desc[i].ops = &bcm590xx_ops_vbus;
+ else {
pmu->desc[i].ops = &bcm590xx_ops_dcdc;
pmu->desc[i].vsel_mask = BCM590XX_SR_VSEL_MASK;
}
- pmu->desc[i].vsel_reg = bcm590xx_get_vsel_register(i);
- pmu->desc[i].enable_is_inverted = true;
- pmu->desc[i].enable_mask = BCM590XX_REG_ENABLE;
+ if (BCM590XX_REG_IS_VBUS(i))
+ pmu->desc[i].enable_mask = BCM590XX_VBUS_ENABLE;
+ else {
+ pmu->desc[i].vsel_reg = bcm590xx_get_vsel_register(i);
+ pmu->desc[i].enable_is_inverted = true;
+ pmu->desc[i].enable_mask = BCM590XX_REG_ENABLE;
+ }
pmu->desc[i].enable_reg = bcm590xx_get_enable_register(i);
pmu->desc[i].type = REGULATOR_VOLTAGE;
pmu->desc[i].owner = THIS_MODULE;
@@ -371,7 +440,10 @@ static int bcm590xx_probe(struct platform_device *pdev)
config.dev = bcm590xx->dev;
config.init_data = reg_data;
config.driver_data = pmu;
- config.regmap = bcm590xx->regmap;
+ if (BCM590XX_REG_IS_GPLDO(i) || BCM590XX_REG_IS_VBUS(i))
+ config.regmap = bcm590xx->regmap_sec;
+ else
+ config.regmap = bcm590xx->regmap_pri;
if (bcm590xx_reg_matches)
config.of_node = bcm590xx_reg_matches[i].of_node;
--
1.8.4
More information about the linux-arm-kernel
mailing list