[PATCH v3 3/3] ARM: dts: overo: Add support for 3.5'' LCD output
Florian Vaussard
florian.vaussard at epfl.ch
Tue May 20 06:58:57 PDT 2014
Alto35 expansion board has a ZIF connector for a 3.5'' LCD.
Add a common include file for this configuration, and use it
on Alto35.
Signed-off-by: Florian Vaussard <florian.vaussard at epfl.ch>
---
arch/arm/boot/dts/omap3-overo-alto35-common.dtsi | 1 +
arch/arm/boot/dts/omap3-overo-common-lcd35.dtsi | 165 +++++++++++++++++++++++
2 files changed, 166 insertions(+)
create mode 100644 arch/arm/boot/dts/omap3-overo-common-lcd35.dtsi
diff --git a/arch/arm/boot/dts/omap3-overo-alto35-common.dtsi b/arch/arm/boot/dts/omap3-overo-alto35-common.dtsi
index 19d6486..7aae8fb 100644
--- a/arch/arm/boot/dts/omap3-overo-alto35-common.dtsi
+++ b/arch/arm/boot/dts/omap3-overo-alto35-common.dtsi
@@ -11,6 +11,7 @@
*/
#include "omap3-overo-common-peripherals.dtsi"
+#include "omap3-overo-common-lcd35.dtsi"
#include <dt-bindings/input/input.h>
diff --git a/arch/arm/boot/dts/omap3-overo-common-lcd35.dtsi b/arch/arm/boot/dts/omap3-overo-common-lcd35.dtsi
new file mode 100644
index 0000000..233c69e
--- /dev/null
+++ b/arch/arm/boot/dts/omap3-overo-common-lcd35.dtsi
@@ -0,0 +1,165 @@
+/*
+ * Copyright (C) 2014 Florian Vaussard, EPFL Mobots group
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+/*
+ * 4.3'' LCD panel output for some Gumstix Overo boards (Gallop43, Chestnut43)
+ */
+
+&omap3_pmx_core {
+ dss_dpi_pins: pinmux_dss_dpi_pins {
+ pinctrl-single,pins = <
+ OMAP3_CORE1_IOPAD(0x20d4, PIN_OUTPUT | MUX_MODE0) /* dss_pclk.dss_pclk */
+ OMAP3_CORE1_IOPAD(0x20d6, PIN_OUTPUT | MUX_MODE0) /* dss_hsync.dss_hsync */
+ OMAP3_CORE1_IOPAD(0x20d8, PIN_OUTPUT | MUX_MODE0) /* dss_vsync.dss_vsync */
+ OMAP3_CORE1_IOPAD(0x20da, PIN_OUTPUT | MUX_MODE0) /* dss_acbias.dss_acbias */
+ OMAP3_CORE1_IOPAD(0x20dc, PIN_OUTPUT | MUX_MODE0) /* dss_data0.dss_data0 */
+ OMAP3_CORE1_IOPAD(0x20de, PIN_OUTPUT | MUX_MODE0) /* dss_data1.dss_data1 */
+ OMAP3_CORE1_IOPAD(0x20e0, PIN_OUTPUT | MUX_MODE0) /* dss_data2.dss_data2 */
+ OMAP3_CORE1_IOPAD(0x20e2, PIN_OUTPUT | MUX_MODE0) /* dss_data3.dss_data3 */
+ OMAP3_CORE1_IOPAD(0x20e4, PIN_OUTPUT | MUX_MODE0) /* dss_data4.dss_data4 */
+ OMAP3_CORE1_IOPAD(0x20e6, PIN_OUTPUT | MUX_MODE0) /* dss_data5.dss_data5 */
+ OMAP3_CORE1_IOPAD(0x20e8, PIN_OUTPUT | MUX_MODE0) /* dss_data6.dss_data6 */
+ OMAP3_CORE1_IOPAD(0x20ea, PIN_OUTPUT | MUX_MODE0) /* dss_data7.dss_data7 */
+ OMAP3_CORE1_IOPAD(0x20ec, PIN_OUTPUT | MUX_MODE0) /* dss_data8.dss_data8 */
+ OMAP3_CORE1_IOPAD(0x20ee, PIN_OUTPUT | MUX_MODE0) /* dss_data9.dss_data9 */
+ OMAP3_CORE1_IOPAD(0x20f0, PIN_OUTPUT | MUX_MODE0) /* dss_data10.dss_data10 */
+ OMAP3_CORE1_IOPAD(0x20f2, PIN_OUTPUT | MUX_MODE0) /* dss_data11.dss_data11 */
+ OMAP3_CORE1_IOPAD(0x20f4, PIN_OUTPUT | MUX_MODE0) /* dss_data12.dss_data12 */
+ OMAP3_CORE1_IOPAD(0x20f6, PIN_OUTPUT | MUX_MODE0) /* dss_data13.dss_data13 */
+ OMAP3_CORE1_IOPAD(0x20f8, PIN_OUTPUT | MUX_MODE0) /* dss_data14.dss_data14 */
+ OMAP3_CORE1_IOPAD(0x20fa, PIN_OUTPUT | MUX_MODE0) /* dss_data15.dss_data15 */
+ OMAP3_CORE1_IOPAD(0x20fc, PIN_OUTPUT | MUX_MODE0) /* dss_data16.dss_data16 */
+ OMAP3_CORE1_IOPAD(0x20fe, PIN_OUTPUT | MUX_MODE0) /* dss_data17.dss_data17 */
+ OMAP3_CORE1_IOPAD(0x2100, PIN_OUTPUT | MUX_MODE0) /* dss_data18.dss_data18 */
+ OMAP3_CORE1_IOPAD(0x2102, PIN_OUTPUT | MUX_MODE0) /* dss_data19.dss_data19 */
+ OMAP3_CORE1_IOPAD(0x2104, PIN_OUTPUT | MUX_MODE0) /* dss_data20.dss_data20 */
+ OMAP3_CORE1_IOPAD(0x2106, PIN_OUTPUT | MUX_MODE0) /* dss_data21.dss_data21 */
+ OMAP3_CORE1_IOPAD(0x2108, PIN_OUTPUT | MUX_MODE0) /* dss_data22.dss_data22 */
+ OMAP3_CORE1_IOPAD(0x210a, PIN_OUTPUT | MUX_MODE0) /* dss_data23.dss_data23 */
+ >;
+ };
+
+ lb035_pins: pinmux_lb035_pins {
+ pinctrl-single,pins = <
+ OMAP3_CORE1_IOPAD(0x2174, PIN_OUTPUT | MUX_MODE4) /* uart2_cts.gpio_144 */
+ >;
+ };
+
+ backlight_pins: pinmux_backlight_pins {
+ pinctrl-single,pins = <
+ OMAP3_CORE1_IOPAD(0x2176, PIN_OUTPUT | MUX_MODE4) /* uart2_rts.gpio_145 */
+ >;
+ };
+
+ mcspi1_pins: pinmux_mcspi1_pins {
+ pinctrl-single,pins = <
+ OMAP3_CORE1_IOPAD(0x21c8, PIN_INPUT | MUX_MODE0) /* mcspi1_clk.mcspi1_clk */
+ OMAP3_CORE1_IOPAD(0x21ca, PIN_INPUT | MUX_MODE0) /* mcspi1_simo.mcspi1_simo */
+ OMAP3_CORE1_IOPAD(0x21cc, PIN_INPUT | MUX_MODE0) /* mcspi1_somi.mcspi1_somi */
+ OMAP3_CORE1_IOPAD(0x21ce, PIN_INPUT | MUX_MODE0) /* mcspi1_cs0.mcspi1_cs0 */
+ >;
+ };
+
+ ads7846_pins: pinmux_ads7846_pins {
+ pinctrl-single,pins = <
+ OMAP3_CORE1_IOPAD(0x2138, PIN_INPUT_PULLDOWN | MUX_MODE4) /* csi2_dx1.gpio_114 */
+ >;
+ };
+};
+
+/* Needed to power the DPI pins */
+&vpll2 {
+ regulator-always-on;
+};
+
+&dss {
+ status = "ok";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&dss_dpi_pins>;
+
+ port {
+ dpi_out: endpoint {
+ remote-endpoint = <&lcd_in>;
+ data-lines = <24>;
+ };
+ };
+};
+
+/ {
+ aliases {
+ display0 = &lcd0;
+ };
+
+ ads7846reg: ads7846-reg {
+ compatible = "regulator-fixed";
+ regulator-name = "ads7846-reg";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ backlight {
+ compatible = "gpio-backlight";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&backlight_pins>;
+ gpios = <&gpio5 17 GPIO_ACTIVE_HIGH>; /* gpio_145 */
+
+ default-on;
+ };
+};
+
+&mcspi1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mcspi1_pins>;
+
+ lcd0: display at 0 {
+ compatible = "lgphilips,lb035q02";
+ label = "lcd";
+
+ reg = <1>; /* CS1 */
+ spi-max-frequency = <10000000>;
+ spi-cpol;
+ spi-cpha;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&lb035_pins>;
+ enable-gpios = <&gpio5 16 GPIO_ACTIVE_HIGH>; /* gpio_144 */
+
+ port {
+ lcd_in: endpoint {
+ remote-endpoint = <&dpi_out>;
+ };
+ };
+ };
+
+ /* touch controller */
+ ads7846 at 0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&ads7846_pins>;
+
+ compatible = "ti,ads7846";
+ vcc-supply = <&ads7846reg>;
+
+ reg = <0>; /* CS0 */
+ spi-max-frequency = <1500000>;
+
+ interrupt-parent = <&gpio4>;
+ interrupts = <18 0>; /* gpio_114 */
+ pendown-gpio = <&gpio4 18 0>;
+
+ ti,x-min = /bits/ 16 <0x0>;
+ ti,x-max = /bits/ 16 <0x0fff>;
+ ti,y-min = /bits/ 16 <0x0>;
+ ti,y-max = /bits/ 16 <0x0fff>;
+ ti,x-plate-ohms = /bits/ 16 <180>;
+ ti,pressure-max = /bits/ 16 <255>;
+
+ linux,wakeup;
+ };
+};
--
1.8.3.2
More information about the linux-arm-kernel
mailing list