[RFC PATCH] ARM: cache-l2x0: add setup entry for l2 in non-secure mode
Gioh Kim
gioh.kim at lge.com
Sun May 18 17:29:52 PDT 2014
2014-05-18 오후 10:13, Barry Song 쓴 글:
> 2014-05-15 13:39 GMT+08:00 Gioh Kim <gioh.kim at lge.com>:
>>
>> Hi,
>>
>> My board is using Trustzone and running kernel is non-secure mode.
>> But setup function of PL310 driver is only for secure mode kernel.
>>
>> What about adding an entry for non-secure mode setup function?
>>
>> I'm sorry for my poor code but I just wanna say what I need .
>
> Gioh,
>
> i don't really understand what is the user scenarios for this, if you
> are running linux in non-secure mode, your security-mode codes have
> enabled L2, so this makes non-secure linux have no chance to execute
> setup at all:
My platform runs linux kernel before L2 cache activation.
And the L2 cache is activated when the kernel sends command to Trustzone firmware.
At this moment L2 is not activated. Linux should send command for L2 activation to Trustzone at the moment.
> 992 /* L2 configuration can only be changed if the cache is disabled */
> 993 if (!(readl_relaxed(l2x0_base + L2X0_CTRL) & L2X0_CTRL_EN)) {
> 994 if (data->setup)
> 995 data->setup(np, &aux_val, &aux_mask);
>
> anyway, cache-l2x0.c supported non-secure linux as you can read:
If non-secure linux try to access l2x0 register, it would generate fault.
If L2 is not activated at l2x0_of_init, follow code can generate fault.
So the L2 should be activated before the follow code.
> 387 /*
> 388 * Check if l2x0 controller is already enabled.
> 389 * If you are booting from non-secure mode
> 390 * accessing the below registers will fault.
> 391 */
> 392 if (!(readl_relaxed(l2x0_base + L2X0_CTRL) & L2X0_CTRL_EN)) {
> 393 /* Make sure that I&D is not locked down when starting */
> 394 l2x0_unlock(cache_id);
> 395
> 396 /* l2x0 controller is disabled */
> 397 writel_relaxed(aux, l2x0_base + L2X0_AUX_CTRL);
> 398
> 399 l2x0_inv_all();
> 400
> 401 /* enable L2X0 */
> 402 writel_relaxed(L2X0_CTRL_EN, l2x0_base + L2X0_CTRL);
> 403 }
>
>
>
>>
>> ------------------------------ 8< -------------------------------
>> From ee4b03fb2c12038c6bbb9f752558abae8d500c07 Mon Sep 17 00:00:00 2001
>> From: Gioh Kim <gioh.kim at lge.com>
>> Date: Thu, 15 May 2014 14:06:36 +0900
>> Subject: [PATCH] ARM: cache-l2x0: add setup entry for l2 in non-secure mode
>>
>> For some platforms using Trustzone and running kernel in non-secure mode,
>> another l2 setup function is necessary.
>>
>> Signed-off-by: Gioh Kim <gioh.kim at lge.c>
>> ---
>> arch/arm/include/asm/hardware/cache-l2x0.h | 9 +++++++++
>> arch/arm/mm/cache-l2x0.c | 26 +++++++++++++++++++++++++-
>> 2 files changed, 34 insertions(+), 1 deletion(-)
>>
>> diff --git a/arch/arm/include/asm/hardware/cache-l2x0.h b/arch/arm/include/asm/hardware/cache-l2x0.h
>> index 6dec6da..de31114 100644
>> --- a/arch/arm/include/asm/hardware/cache-l2x0.h
>> +++ b/arch/arm/include/asm/hardware/cache-l2x0.h
>> @@ -21,6 +21,7 @@
>> #define __ASM_ARM_HARDWARE_L2X0_H
>>
>> #include <linux/errno.h>
>> +#include <linux/of.h>
>>
>> #define L2X0_CACHE_ID 0x000
>> #define L2X0_CACHE_TYPE 0x004
>> @@ -110,11 +111,19 @@
>> extern void __init l2x0_init(void __iomem *base, u32 aux_val, u32 aux_mask);
>> #if defined(CONFIG_CACHE_L2X0) && defined(CONFIG_OF)
>> extern int l2x0_of_init(u32 aux_val, u32 aux_mask);
>> +extern int l2x0_of_set_setup_nonsecure(const char *compatible, size_t len,
>> + void (*fp)(const struct device_node *, u32 *, u32 *));
>> #else
>> static inline int l2x0_of_init(u32 aux_val, u32 aux_mask)
>> {
>> return -ENODEV;
>> }
>> +static inline int l2x0_of_set_setup_nonsecure(const char *compatible,
>> + size_t len,
>> + void (*fp)(const struct device_node *, u32 *, u32 *))
>> +{
>> + return -ENODEV;
>> +}
>> #endif
>>
>> struct l2x0_regs {
>> diff --git a/arch/arm/mm/cache-l2x0.c b/arch/arm/mm/cache-l2x0.c
>> index 728d644..582ea37 100644
>> --- a/arch/arm/mm/cache-l2x0.c
>> +++ b/arch/arm/mm/cache-l2x0.c
>> @@ -45,6 +45,7 @@ struct l2x0_regs l2x0_saved_regs;
>> struct l2x0_of_data {
>> void (*setup)(const struct device_node *, u32 *, u32 *);
>> void (*save)(void);
>> + void (*setup_nonsecure)(const struct device_node *, u32 *, u32 *);
>> struct outer_cache_fns outer_cache;
>> };
>>
>> @@ -968,6 +969,23 @@ static const struct of_device_id l2x0_ids[] __initconst = {
>> {}
>> };
>>
>> +int l2x0_of_set_setup_nonsecure(const char *compatible, size_t len,
>> + void (*fp)(const struct device_node *, u32 *, u32 *))
>> +{
>> + const struct of_device_id *id;
>> +
>> + for (id = &l2x0_ids[0]; id->compatible != NULL; id++) {
>> + if (strncmp(id->compatible, compatible, len) == 0) {
>> + struct l2x0_of_data *data = id->data;
>> +
>> + data->setup_nonsecure = fp;
>> + return 0;
>> + }
>> + }
>> +
>> + return -EINVAL;
>> +}
>> +
>> int __init l2x0_of_init(u32 aux_val, u32 aux_mask)
>> {
>> struct device_node *np;
>> @@ -989,8 +1007,14 @@ int __init l2x0_of_init(u32 aux_val, u32 aux_mask)
>>
>> /* L2 configuration can only be changed if the cache is disabled */
>> if (!(readl_relaxed(l2x0_base + L2X0_CTRL) & L2X0_CTRL_EN)) {
>> - if (data->setup)
>> +
>> + if (data->setup_nonsecure)
>> + data->setup_nonsecure(np, &aux_val, &aux_mask);
>> + else if (data->setup)
>> data->setup(np, &aux_val, &aux_mask);
>> + else
>> + /* no function to enable cache */
>> + return -ENODEV;
>>
>> /* For aurora cache in no outer mode select the
>> * correct mode using the coprocessor*/
>> --
>> 1.7.9.5
>
>
> -barry
>
More information about the linux-arm-kernel
mailing list