[PATCH 02/11] ARM: shmobile: henninger: add SDHI0/2 DT support

Simon Horman horms+renesas at verge.net.au
Thu May 15 17:58:11 PDT 2014


From: Sergei Shtylyov <sergei.shtylyov at cogentembedded.com>

Define the Henninger board dependent part of the SDHI0/2 device nodes along with
the necessary voltage regulators (note that the Vcc regulators are dummy -- they
are required but don't actually exist on the board). Also, GPIOs have to be used
for the CD and WP signals due to the SDHI driver constraints...

Signed-off-by: Sergei Shtylyov <sergei.shtylyov at cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas at verge.net.au>
---
 arch/arm/boot/dts/r8a7791-henninger.dts | 76 +++++++++++++++++++++++++++++++++
 1 file changed, 76 insertions(+)

diff --git a/arch/arm/boot/dts/r8a7791-henninger.dts b/arch/arm/boot/dts/r8a7791-henninger.dts
index 0a65523..2e45c06 100644
--- a/arch/arm/boot/dts/r8a7791-henninger.dts
+++ b/arch/arm/boot/dts/r8a7791-henninger.dts
@@ -11,6 +11,7 @@
 
 /dts-v1/;
 #include "r8a7791.dtsi"
+#include <dt-bindings/gpio/gpio.h>
 
 / {
 	model = "Henninger";
@@ -33,6 +34,50 @@
 		device_type = "memory";
 		reg = <2 0x00000000 0 0x40000000>;
 	};
+
+	vcc_sdhi0: regulator at 0 {
+		compatible = "regulator-fixed";
+
+		regulator-name = "SDHI0 Vcc";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+	};
+
+	vccq_sdhi0: regulator at 1 {
+		compatible = "regulator-gpio";
+
+		regulator-name = "SDHI0 VccQ";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <3300000>;
+
+		gpios = <&gpio2 12 GPIO_ACTIVE_HIGH>;
+		gpios-states = <1>;
+		states = <3300000 1
+			  1800000 0>;
+	};
+
+	vcc_sdhi2: regulator at 2 {
+		compatible = "regulator-fixed";
+
+		regulator-name = "SDHI2 Vcc";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+	};
+
+	vccq_sdhi2: regulator at 3 {
+		compatible = "regulator-gpio";
+
+		regulator-name = "SDHI2 VccQ";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <3300000>;
+
+		gpios = <&gpio2 26 GPIO_ACTIVE_HIGH>;
+		gpios-states = <1>;
+		states = <3300000 1
+			  1800000 0>;
+	};
 };
 
 &extal_clk {
@@ -54,6 +99,16 @@
 		renesas,groups = "intc_irq0";
 		renesas,function = "intc";
 	};
+
+	sdhi0_pins: sd0 {
+		renesas,groups = "sdhi0_data4", "sdhi0_ctrl";
+		renesas,function = "sdhi0";
+	};
+
+	sdhi2_pins: sd2 {
+		renesas,groups = "sdhi2_data4", "sdhi2_ctrl";
+		renesas,function = "sdhi2";
+	};
 };
 
 &scif0 {
@@ -82,3 +137,24 @@
 &sata0 {
        status = "okay";
 };
+
+&sdhi0 {
+	pinctrl-0 = <&sdhi0_pins>;
+	pinctrl-names = "default";
+
+	vmmc-supply = <&vcc_sdhi0>;
+	vqmmc-supply = <&vccq_sdhi0>;
+	cd-gpios = <&gpio6 6 GPIO_ACTIVE_LOW>;
+	wp-gpios = <&gpio6 7 GPIO_ACTIVE_HIGH>;
+	status = "okay";
+};
+
+&sdhi2 {
+	pinctrl-0 = <&sdhi2_pins>;
+	pinctrl-names = "default";
+
+	vmmc-supply = <&vcc_sdhi2>;
+	vqmmc-supply = <&vccq_sdhi2>;
+	cd-gpios = <&gpio6 22 GPIO_ACTIVE_LOW>;
+	status = "okay";
+};
-- 
1.8.5.2




More information about the linux-arm-kernel mailing list