[PATCH v3 3/6] ata: ahci: add AHCI support for the Berlin BG2Q
Antoine Ténart
antoine.tenart at free-electrons.com
Wed May 14 02:48:59 PDT 2014
Add support for the Berlin BG2Q AHCI SATA controller allowing to
interface with devices like external hard drives.
Signed-off-by: Antoine Ténart <antoine.tenart at free-electrons.com>
---
drivers/ata/Kconfig | 10 +++
drivers/ata/Makefile | 1 +
drivers/ata/ahci_berlin.c | 202 ++++++++++++++++++++++++++++++++++++++++++++++
3 files changed, 213 insertions(+)
create mode 100644 drivers/ata/ahci_berlin.c
diff --git a/drivers/ata/Kconfig b/drivers/ata/Kconfig
index c2706047337f..37e6817b31f4 100644
--- a/drivers/ata/Kconfig
+++ b/drivers/ata/Kconfig
@@ -97,6 +97,16 @@ config SATA_AHCI_PLATFORM
If unsure, say N.
+config AHCI_BERLIN
+ tristate "Marvell Berlin AHCI SATA support"
+ depends on ARCH_BERLIN
+ select PHY_BERLIN_SATA
+ help
+ This option enables support for the Marvell Berlin SoC's
+ onboard AHCI SATA.
+
+ If unsure, say N.
+
config AHCI_DA850
tristate "DaVinci DA850 AHCI SATA support"
depends on ARCH_DAVINCI_DA850
diff --git a/drivers/ata/Makefile b/drivers/ata/Makefile
index 44c8016e565c..7fb78d1e0a44 100644
--- a/drivers/ata/Makefile
+++ b/drivers/ata/Makefile
@@ -10,6 +10,7 @@ obj-$(CONFIG_SATA_INIC162X) += sata_inic162x.o
obj-$(CONFIG_SATA_SIL24) += sata_sil24.o
obj-$(CONFIG_SATA_DWC) += sata_dwc_460ex.o
obj-$(CONFIG_SATA_HIGHBANK) += sata_highbank.o libahci.o
+obj-$(CONFIG_AHCI_BERLIN) += ahci_berlin.o libahci.o libahci_platform.o
obj-$(CONFIG_AHCI_DA850) += ahci_da850.o libahci.o libahci_platform.o
obj-$(CONFIG_AHCI_IMX) += ahci_imx.o libahci.o libahci_platform.o
obj-$(CONFIG_AHCI_SUNXI) += ahci_sunxi.o libahci.o libahci_platform.o
diff --git a/drivers/ata/ahci_berlin.c b/drivers/ata/ahci_berlin.c
new file mode 100644
index 000000000000..973c07e54a6a
--- /dev/null
+++ b/drivers/ata/ahci_berlin.c
@@ -0,0 +1,202 @@
+/*
+ * Marvell Berlin AHCI SATA platform driver
+ *
+ * Copyright (C) 2014 Marvell Technology Group Ltd.
+ *
+ * Antoine Ténart <antoine.tenart at free-electrons.com>
+ * Jisheng Zhang <jszhang at marvell.com>
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2. This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+
+#include <linux/ahci_platform.h>
+#include <linux/module.h>
+#include <linux/of_device.h>
+#include <linux/platform_device.h>
+
+#include "ahci.h"
+
+#define BERLIN_SATA_NPORTS 2
+
+#define PORT_VSR_ADDR 0x78
+#define PORT_VSR_DATA 0x7c
+
+#define PHY_BASE 0x200
+
+/* register 0x01 */
+#define REF_FREF_SEL_25 BIT(0)
+#define PHY_MODE_SATA (0x0 << 5)
+
+/* register 0x02 */
+#define USE_MAX_PLL_RATE BIT(12)
+
+/* register 0x23 */
+#define DATA_BIT_WIDTH_10 (0x0 << 10)
+#define DATA_BIT_WIDTH_20 (0x1 << 10)
+#define DATA_BIT_WIDTH_40 (0x2 << 10)
+
+/* register 0x25 */
+#define PHY_GEN_MAX_1_5 (0x0 << 10)
+#define PHY_GEN_MAX_3_0 (0x1 << 10)
+#define PHY_GEN_MAX_6_0 (0x2 << 10)
+
+struct berlin_ahci_priv {
+ struct ahci_host_priv *hpriv;
+ struct phy *phys[BERLIN_SATA_NPORTS];
+};
+
+static inline void ahci_berlin_reg_setbits(void __iomem *ctrl_reg, u32 reg,
+ u32 mask, u32 val)
+{
+ u32 regval;
+
+ /* select register */
+ writel(PHY_BASE + reg, ctrl_reg + PORT_VSR_ADDR);
+
+ /* set bits */
+ regval = readl(ctrl_reg + PORT_VSR_DATA);
+ regval &= ~mask;
+ regval |= val;
+ writel(regval, ctrl_reg + PORT_VSR_DATA);
+}
+
+static void ahci_berlin_port_init(struct ahci_host_priv *hpriv,
+ unsigned int port)
+{
+ struct berlin_ahci_priv *berlin_priv = hpriv->plat_data;
+ void __iomem *ctrl_reg = hpriv->mmio + 0x100 + (port * 0x80);
+
+ /* power on the PHY */
+ phy_power_on(berlin_priv->phys[port]);
+
+ /* set PHY mode to SATA, ref freq to 25 MHz */
+ ahci_berlin_reg_setbits(ctrl_reg, 0x1, 0xff, REF_FREF_SEL_25 | PHY_MODE_SATA);
+
+ /* set PHY up to 6 Gbps */
+ ahci_berlin_reg_setbits(ctrl_reg, 0x25, 0xc00, PHY_GEN_MAX_6_0);
+
+ /* set 40 bits width */
+ ahci_berlin_reg_setbits(ctrl_reg, 0x23, 0xc00, DATA_BIT_WIDTH_40);
+
+ /* use max pll rate */
+ ahci_berlin_reg_setbits(ctrl_reg, 0x2, 0x0, USE_MAX_PLL_RATE);
+
+ /* set the controller speed */
+ writel(0x31, ctrl_reg + PORT_SCR_CTL);
+}
+
+static const struct ata_port_info ahci_berlin_port_info = {
+ .flags = AHCI_FLAG_COMMON | ATA_FLAG_NCQ,
+ .pio_mask = ATA_PIO4,
+ .udma_mask = ATA_UDMA6,
+ .port_ops = &ahci_platform_ops,
+};
+
+static int ahci_berlin_probe(struct platform_device *pdev)
+{
+ struct device *dev = &pdev->dev;
+ struct ahci_host_priv *hpriv;
+ struct berlin_ahci_priv *berlin_priv;
+ int ret, i = 0;
+ unsigned mask = 0;
+
+ hpriv = ahci_platform_get_resources(pdev);
+ if (IS_ERR(hpriv)) {
+ dev_err(dev, "cannot get AHCI resources\n");
+ return PTR_ERR(hpriv);
+ }
+
+ berlin_priv = devm_kzalloc(dev, sizeof(*berlin_priv), GFP_KERNEL);
+ if (!berlin_priv)
+ return -ENOMEM;
+
+ hpriv->plat_data = berlin_priv;
+
+ ret = ahci_platform_enable_resources(hpriv);
+ if (ret) {
+ dev_err(dev, "cannot enable resources: %d\n", ret);
+ return ret;
+ }
+
+ for (i = 0; i < BERLIN_SATA_NPORTS; i++) {
+ char phy_name[6];
+
+ sprintf(phy_name, "port%d", i);
+
+ berlin_priv->phys[i] = devm_phy_get(dev, phy_name);
+ if (IS_ERR(berlin_priv->phys[i])) {
+ dev_warn(dev, "%s not available\n", phy_name);
+ continue;
+ }
+
+ mask |= 1 << i;
+ ahci_berlin_port_init(hpriv, i);
+ }
+
+ ret = ahci_platform_init_host(pdev, hpriv, &ahci_berlin_port_info,
+ 0, mask);
+ if (ret) {
+ dev_err(dev, "host init failed: %d\n", ret);
+ goto disable_resources;
+ }
+
+ return 0;
+
+disable_resources:
+ ahci_platform_disable_resources(hpriv);
+ return ret;
+}
+
+#ifdef CONFIG_PM_SLEEP
+static int ahci_berlin_resume(struct device *dev)
+{
+ struct ata_host *host = dev_get_drvdata(dev);
+ struct ahci_host_priv *hpriv = host->private_data;
+ struct berlin_ahci_priv *berlin_priv = hpriv->plat_data;
+ int ret, i;
+
+ ret = ahci_platform_enable_resources(hpriv);
+ if (ret)
+ return ret;
+
+ for (i = 0; i < BERLIN_SATA_NPORTS; i++) {
+ if (!IS_ERR(berlin_priv->phys[i]))
+ ahci_berlin_port_init(hpriv, i);
+ }
+
+ ret = ahci_platform_resume_host(dev);
+ if (ret) {
+ ahci_platform_disable_resources(hpriv);
+ return ret;
+ }
+
+ return 0;
+}
+#endif
+
+static SIMPLE_DEV_PM_OPS(ahci_berlin_pm_ops, ahci_platform_suspend,
+ ahci_berlin_resume);
+
+static const struct of_device_id ahci_berlin_of_match[] = {
+ { .compatible = "marvell,berlin-ahci" },
+ { },
+};
+MODULE_DEVICE_TABLE(of, ahci_berlin_of_match);
+
+static struct platform_driver ahci_berlin_driver = {
+ .probe = ahci_berlin_probe,
+ .remove = ata_platform_remove_one,
+ .driver = {
+ .name = "ahci-berlin",
+ .owner = THIS_MODULE,
+ .of_match_table = ahci_berlin_of_match,
+ .pm = &ahci_berlin_pm_ops,
+ },
+};
+module_platform_driver(ahci_berlin_driver);
+
+MODULE_DESCRIPTION("Marvell Berlin AHCI SATA driver");
+MODULE_AUTHOR("Antoine Ténart <antoine.tenart at free-electrons.com>");
+MODULE_LICENSE("GPL");
--
1.9.1
More information about the linux-arm-kernel
mailing list