[PATCH 5/6] ARM: dts: imx: add initial imx6sx device tree source
Shawn Guo
shawn.guo at freescale.com
Tue May 13 07:12:18 PDT 2014
Add initial device tree source for i.MX6 SoloX SoC.
Signed-off-by: Anson Huang <b20788 at freescale.com>
Signed-off-by: Shawn Guo <shawn.guo at freescale.com>
---
arch/arm/boot/dts/imx6sx.dtsi | 1202 +++++++++++++++++++++++++++++++++++++++++
1 file changed, 1202 insertions(+)
create mode 100644 arch/arm/boot/dts/imx6sx.dtsi
diff --git a/arch/arm/boot/dts/imx6sx.dtsi b/arch/arm/boot/dts/imx6sx.dtsi
new file mode 100644
index 0000000..ac3866c
--- /dev/null
+++ b/arch/arm/boot/dts/imx6sx.dtsi
@@ -0,0 +1,1202 @@
+/*
+ * Copyright 2014 Freescale Semiconductor, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <dt-bindings/clock/imx6sx-clock.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include "imx6sx-pinfunc.h"
+#include "skeleton.dtsi"
+
+/ {
+ aliases {
+ can0 = &flexcan1;
+ can1 = &flexcan2;
+ ethernet0 = &fec1;
+ ethernet1 = &fec2;
+ gpio0 = &gpio1;
+ gpio1 = &gpio2;
+ gpio2 = &gpio3;
+ gpio3 = &gpio4;
+ gpio4 = &gpio5;
+ gpio5 = &gpio6;
+ gpio6 = &gpio7;
+ i2c0 = &i2c1;
+ i2c1 = &i2c2;
+ i2c2 = &i2c3;
+ i2c3 = &i2c4;
+ mmc0 = &usdhc1;
+ mmc1 = &usdhc2;
+ mmc2 = &usdhc3;
+ mmc3 = &usdhc4;
+ serial0 = &uart1;
+ serial1 = &uart2;
+ serial2 = &uart3;
+ serial3 = &uart4;
+ serial4 = &uart5;
+ serial5 = &uart6;
+ spi0 = &ecspi1;
+ spi1 = &ecspi2;
+ spi2 = &ecspi3;
+ spi3 = &ecspi4;
+ spi4 = &ecspi5;
+ usbphy0 = &usbphy1;
+ usbphy1 = &usbphy2;
+ };
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ cpu0: cpu at 0 {
+ compatible = "arm,cortex-a9";
+ device_type = "cpu";
+ reg = <0>;
+ next-level-cache = <&L2>;
+ operating-points = <
+ /* kHz uV */
+ 996000 1250000
+ 792000 1175000
+ 396000 1075000
+ >;
+ fsl,soc-operating-points = <
+ /* ARM kHz SOC uV */
+ 996000 1175000
+ 792000 1175000
+ 396000 1175000
+ >;
+ clock-latency = <61036>; /* two CLK32 periods */
+ clocks = <&clks IMX6SX_CLK_ARM>,
+ <&clks IMX6SX_CLK_PLL2_PFD2>,
+ <&clks IMX6SX_CLK_STEP>,
+ <&clks IMX6SX_CLK_PLL1_SW>,
+ <&clks IMX6SX_CLK_PLL1_SYS>;
+ clock-names = "arm", "pll2_pfd2_396m", "step",
+ "pll1_sw", "pll1_sys";
+ arm-supply = <®_arm>;
+ soc-supply = <®_soc>;
+ };
+ };
+
+ intc: interrupt-controller at 00a01000 {
+ compatible = "arm,cortex-a9-gic";
+ #interrupt-cells = <3>;
+ interrupt-controller;
+ reg = <0x00a01000 0x1000>,
+ <0x00a00100 0x100>;
+ };
+
+ clocks {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ckil: clock at 0 {
+ compatible = "fixed-clock";
+ reg = <0>;
+ #clock-cells = <0>;
+ clock-frequency = <32768>;
+ clock-output-names = "ckil";
+ };
+
+ osc: clock at 1 {
+ compatible = "fixed-clock";
+ reg = <1>;
+ #clock-cells = <0>;
+ clock-frequency = <24000000>;
+ clock-output-names = "osc";
+ };
+
+ ipp_di0: clock at 2 {
+ compatible = "fixed-clock";
+ reg = <2>;
+ #clock-cells = <0>;
+ clock-frequency = <0>;
+ clock-output-names = "ipp_di0";
+ };
+
+ ipp_di1: clock at 3 {
+ compatible = "fixed-clock";
+ reg = <3>;
+ #clock-cells = <0>;
+ clock-frequency = <0>;
+ clock-output-names = "ipp_di1";
+ };
+ };
+
+ soc {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "simple-bus";
+ interrupt-parent = <&intc>;
+ ranges;
+
+ pmu {
+ compatible = "arm,cortex-a9-pmu";
+ interrupts = <GIC_SPI 94 IRQ_TYPE_LEVEL_HIGH>;
+ };
+
+ ocram: sram at 00900000 {
+ compatible = "mmio-sram";
+ reg = <0x00900000 0x20000>;
+ clocks = <&clks IMX6SX_CLK_OCRAM>;
+ };
+
+ L2: l2-cache at 00a02000 {
+ compatible = "arm,pl310-cache";
+ reg = <0x00a02000 0x1000>;
+ interrupts = <GIC_SPI 92 IRQ_TYPE_LEVEL_HIGH>;
+ cache-unified;
+ cache-level = <2>;
+ arm,tag-latency = <4 2 3>;
+ arm,data-latency = <4 2 3>;
+ };
+
+ dma_apbh: dma-apbh at 01804000 {
+ compatible = "fsl,imx6sx-dma-apbh", "fsl,imx28-dma-apbh";
+ reg = <0x01804000 0x2000>;
+ interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "gpmi0", "gpmi1", "gpmi2", "gpmi3";
+ #dma-cells = <1>;
+ dma-channels = <4>;
+ clocks = <&clks IMX6SX_CLK_APBH_DMA>;
+ };
+
+ gpmi: gpmi-nand at 01806000{
+ compatible = "fsl,imx6sx-gpmi-nand";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ reg = <0x01806000 0x2000>, <0x01808000 0x4000>;
+ reg-names = "gpmi-nand", "bch";
+ interrupts = <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "bch";
+ clocks = <&clks IMX6SX_CLK_GPMI_IO>,
+ <&clks IMX6SX_CLK_GPMI_APB>,
+ <&clks IMX6SX_CLK_GPMI_BCH>,
+ <&clks IMX6SX_CLK_GPMI_BCH_APB>,
+ <&clks IMX6SX_CLK_PER1_BCH>;
+ clock-names = "gpmi_io", "gpmi_apb", "gpmi_bch",
+ "gpmi_bch_apb", "per1_bch";
+ dmas = <&dma_apbh 0>;
+ dma-names = "rx-tx";
+ status = "disabled";
+ };
+
+ aips1: aips-bus at 02000000 {
+ compatible = "fsl,aips-bus", "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ reg = <0x02000000 0x100000>;
+ ranges;
+
+ spba-bus at 02000000 {
+ compatible = "fsl,spba-bus", "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ reg = <0x02000000 0x40000>;
+ ranges;
+
+ spdif: spdif at 02004000 {
+ compatible = "fsl,imx6sx-spdif", "fsl,imx35-spdif";
+ reg = <0x02004000 0x4000>;
+ interrupts = <GIC_SPI 52 IRQ_TYPE_LEVEL_HIGH>;
+ dmas = <&sdma 14 18 0>,
+ <&sdma 15 18 0>;
+ dma-names = "rx", "tx";
+ clocks = <&clks IMX6SX_CLK_SPDIF>,
+ <&clks IMX6SX_CLK_OSC>,
+ <&clks IMX6SX_CLK_SPDIF>,
+ <&clks 0>, <&clks 0>, <&clks 0>,
+ <&clks IMX6SX_CLK_IPG>,
+ <&clks 0>, <&clks 0>,
+ <&clks IMX6SX_CLK_SPBA>;
+ clock-names = "core", "rxtx0",
+ "rxtx1", "rxtx2",
+ "rxtx3", "rxtx4",
+ "rxtx5", "rxtx6",
+ "rxtx7", "dma";
+ status = "disabled";
+ };
+
+ ecspi1: ecspi at 02008000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,imx6sx-ecspi", "fsl,imx51-ecspi";
+ reg = <0x02008000 0x4000>;
+ interrupts = <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX6SX_CLK_ECSPI1>,
+ <&clks IMX6SX_CLK_ECSPI1>;
+ clock-names = "ipg", "per";
+ status = "disabled";
+ };
+
+ ecspi2: ecspi at 0200c000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,imx6sx-ecspi", "fsl,imx51-ecspi";
+ reg = <0x0200c000 0x4000>;
+ interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX6SX_CLK_ECSPI2>,
+ <&clks IMX6SX_CLK_ECSPI2>;
+ clock-names = "ipg", "per";
+ status = "disabled";
+ };
+
+ ecspi3: ecspi at 02010000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,imx6sx-ecspi", "fsl,imx51-ecspi";
+ reg = <0x02010000 0x4000>;
+ interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX6SX_CLK_ECSPI3>,
+ <&clks IMX6SX_CLK_ECSPI3>;
+ clock-names = "ipg", "per";
+ status = "disabled";
+ };
+
+ ecspi4: ecspi at 02014000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,imx6sx-ecspi", "fsl,imx51-ecspi";
+ reg = <0x02014000 0x4000>;
+ interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX6SX_CLK_ECSPI4>,
+ <&clks IMX6SX_CLK_ECSPI4>;
+ clock-names = "ipg", "per";
+ status = "disabled";
+ };
+
+ uart1: serial at 02020000 {
+ compatible = "fsl,imx6sx-uart", "fsl,imx21-uart";
+ reg = <0x02020000 0x4000>;
+ interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX6SX_CLK_UART_IPG>,
+ <&clks IMX6SX_CLK_UART_SERIAL>;
+ clock-names = "ipg", "per";
+ dmas = <&sdma 25 4 0>, <&sdma 26 4 0>;
+ dma-names = "rx", "tx";
+ status = "disabled";
+ };
+
+ esai: esai at 02024000 {
+ reg = <0x02024000 0x4000>;
+ interrupts = <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX6SX_CLK_ESAI_IPG>,
+ <&clks IMX6SX_CLK_ESAI_MEM>,
+ <&clks IMX6SX_CLK_ESAI_EXTAL>,
+ <&clks IMX6SX_CLK_ESAI_IPG>,
+ <&clks IMX6SX_CLK_SPBA>;
+ clock-names = "core", "mem", "extal",
+ "fsys", "dma";
+ status = "disabled";
+ };
+
+ ssi1: ssi at 02028000 {
+ compatible = "fsl,imx6sx-ssi", "fsl,imx21-ssi";
+ reg = <0x02028000 0x4000>;
+ interrupts = <GIC_SPI 46 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX6SX_CLK_SSI1_IPG>,
+ <&clks IMX6SX_CLK_SSI1>;
+ clock-names = "ipg", "baud";
+ dmas = <&sdma 37 1 0>, <&sdma 38 1 0>;
+ dma-names = "rx", "tx";
+ status = "disabled";
+ };
+
+ ssi2: ssi at 0202c000 {
+ compatible = "fsl,imx6sx-ssi", "fsl,imx21-ssi";
+ reg = <0x0202c000 0x4000>;
+ interrupts = <GIC_SPI 47 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX6SX_CLK_SSI2_IPG>,
+ <&clks IMX6SX_CLK_SSI2>;
+ clock-names = "ipg", "baud";
+ dmas = <&sdma 41 1 0>, <&sdma 42 1 0>;
+ dma-names = "rx", "tx";
+ status = "disabled";
+ };
+
+ ssi3: ssi at 02030000 {
+ compatible = "fsl,imx6sx-ssi", "fsl,imx21-ssi";
+ reg = <0x02030000 0x4000>;
+ interrupts = <GIC_SPI 48 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX6SX_CLK_SSI3_IPG>,
+ <&clks IMX6SX_CLK_SSI3>;
+ clock-names = "ipg", "baud";
+ dmas = <&sdma 45 1 0>, <&sdma 46 1 0>;
+ dma-names = "rx", "tx";
+ status = "disabled";
+ };
+
+ asrc: asrc at 02034000 {
+ reg = <0x02034000 0x4000>;
+ interrupts = <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX6SX_CLK_ASRC_MEM>,
+ <&clks IMX6SX_CLK_ASRC_IPG>,
+ <&clks IMX6SX_CLK_SPDIF>,
+ <&clks IMX6SX_CLK_SPBA>;
+ clock-names = "mem", "ipg", "asrck", "dma";
+ dmas = <&sdma 17 20 1>, <&sdma 18 20 1>,
+ <&sdma 19 20 1>, <&sdma 20 20 1>,
+ <&sdma 21 20 1>, <&sdma 22 20 1>;
+ dma-names = "rxa", "rxb", "rxc",
+ "txa", "txb", "txc";
+ status = "okay";
+ };
+ };
+
+ pwm1: pwm at 02080000 {
+ compatible = "fsl,imx6sx-pwm", "fsl,imx27-pwm";
+ reg = <0x02080000 0x4000>;
+ interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX6SX_CLK_PWM1>,
+ <&clks IMX6SX_CLK_PWM1>;
+ clock-names = "ipg", "per";
+ #pwm-cells = <2>;
+ };
+
+ pwm2: pwm at 02084000 {
+ compatible = "fsl,imx6sx-pwm", "fsl,imx27-pwm";
+ reg = <0x02084000 0x4000>;
+ interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX6SX_CLK_PWM2>,
+ <&clks IMX6SX_CLK_PWM2>;
+ clock-names = "ipg", "per";
+ #pwm-cells = <2>;
+ };
+
+ pwm3: pwm at 02088000 {
+ compatible = "fsl,imx6sx-pwm", "fsl,imx27-pwm";
+ reg = <0x02088000 0x4000>;
+ interrupts = <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX6SX_CLK_PWM3>,
+ <&clks IMX6SX_CLK_PWM3>;
+ clock-names = "ipg", "per";
+ #pwm-cells = <2>;
+ };
+
+ pwm4: pwm at 0208c000 {
+ compatible = "fsl,imx6sx-pwm", "fsl,imx27-pwm";
+ reg = <0x0208c000 0x4000>;
+ interrupts = <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX6SX_CLK_PWM4>,
+ <&clks IMX6SX_CLK_PWM4>;
+ clock-names = "ipg", "per";
+ #pwm-cells = <2>;
+ };
+
+ flexcan1: can at 02090000 {
+ compatible = "fsl,imx6sx-flexcan", "fsl,imx6q-flexcan";
+ reg = <0x02090000 0x4000>;
+ interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX6SX_CLK_CAN1_IPG>,
+ <&clks IMX6SX_CLK_CAN1_SERIAL>;
+ clock-names = "ipg", "per";
+ status = "disabled";
+ };
+
+ flexcan2: can at 02094000 {
+ compatible = "fsl,imx6sx-flexcan", "fsl,imx6q-flexcan";
+ reg = <0x02094000 0x4000>;
+ interrupts = <GIC_SPI 111 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX6SX_CLK_CAN2_IPG>,
+ <&clks IMX6SX_CLK_CAN2_SERIAL>;
+ clock-names = "ipg", "per";
+ status = "disabled";
+ };
+
+ gpt: gpt at 02098000 {
+ compatible = "fsl,imx6sx-gpt", "fsl,imx31-gpt";
+ reg = <0x02098000 0x4000>;
+ interrupts = <GIC_SPI 55 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX6SX_CLK_GPT_BUS>,
+ <&clks IMX6SX_CLK_GPT_SERIAL>;
+ clock-names = "ipg", "per";
+ };
+
+ gpio1: gpio at 0209c000 {
+ compatible = "fsl,imx6sx-gpio", "fsl,imx35-gpio";
+ reg = <0x0209c000 0x4000>;
+ interrupts = <GIC_SPI 66 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 67 IRQ_TYPE_LEVEL_HIGH>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpio2: gpio at 020a0000 {
+ compatible = "fsl,imx6sx-gpio", "fsl,imx35-gpio";
+ reg = <0x020a0000 0x4000>;
+ interrupts = <GIC_SPI 68 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpio3: gpio at 020a4000 {
+ compatible = "fsl,imx6sx-gpio", "fsl,imx35-gpio";
+ reg = <0x020a4000 0x4000>;
+ interrupts = <GIC_SPI 70 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 71 IRQ_TYPE_LEVEL_HIGH>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpio4: gpio at 020a8000 {
+ compatible = "fsl,imx6sx-gpio", "fsl,imx35-gpio";
+ reg = <0x020a8000 0x4000>;
+ interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpio5: gpio at 020ac000 {
+ compatible = "fsl,imx6sx-gpio", "fsl,imx35-gpio";
+ reg = <0x020ac000 0x4000>;
+ interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpio6: gpio at 020b0000 {
+ compatible = "fsl,imx6sx-gpio", "fsl,imx35-gpio";
+ reg = <0x020b0000 0x4000>;
+ interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpio7: gpio at 020b4000 {
+ compatible = "fsl,imx6sx-gpio", "fsl,imx35-gpio";
+ reg = <0x020b4000 0x4000>;
+ interrupts = <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 79 IRQ_TYPE_LEVEL_HIGH>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ kpp: kpp at 020b8000 {
+ compatible = "fsl,imx6sx-kpp", "fsl,imx21-kpp";
+ reg = <0x020b8000 0x4000>;
+ interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX6SX_CLK_DUMMY>;
+ status = "disabled";
+ };
+
+ wdog1: wdog at 020bc000 {
+ compatible = "fsl,imx6sx-wdt", "fsl,imx21-wdt";
+ reg = <0x020bc000 0x4000>;
+ interrupts = <GIC_SPI 80 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX6SX_CLK_DUMMY>;
+ };
+
+ wdog2: wdog at 020c0000 {
+ compatible = "fsl,imx6sx-wdt", "fsl,imx21-wdt";
+ reg = <0x020c0000 0x4000>;
+ interrupts = <GIC_SPI 81 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX6SX_CLK_DUMMY>;
+ status = "disabled";
+ };
+
+ clks: ccm at 020c4000 {
+ compatible = "fsl,imx6sx-ccm";
+ reg = <0x020c4000 0x4000>;
+ interrupts = <GIC_SPI 87 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 88 IRQ_TYPE_LEVEL_HIGH>;
+ #clock-cells = <1>;
+ clocks = <&ckil>, <&osc>, <&ipp_di0>, <&ipp_di1>;
+ clock-names = "ckil", "osc", "ipp_di0", "ipp_di1";
+ };
+
+ anatop: anatop at 020c8000 {
+ compatible = "fsl,imx6sx-anatop", "fsl,imx6q-anatop",
+ "syscon", "simple-bus";
+ reg = <0x020c8000 0x1000>;
+ interrupts = <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 54 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 127 IRQ_TYPE_LEVEL_HIGH>;
+
+ regulator-1p1 at 110 {
+ compatible = "fsl,anatop-regulator";
+ regulator-name = "vdd1p1";
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1375000>;
+ regulator-always-on;
+ anatop-reg-offset = <0x110>;
+ anatop-vol-bit-shift = <8>;
+ anatop-vol-bit-width = <5>;
+ anatop-min-bit-val = <4>;
+ anatop-min-voltage = <800000>;
+ anatop-max-voltage = <1375000>;
+ };
+
+ regulator-3p0 at 120 {
+ compatible = "fsl,anatop-regulator";
+ regulator-name = "vdd3p0";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <3150000>;
+ regulator-always-on;
+ anatop-reg-offset = <0x120>;
+ anatop-vol-bit-shift = <8>;
+ anatop-vol-bit-width = <5>;
+ anatop-min-bit-val = <0>;
+ anatop-min-voltage = <2625000>;
+ anatop-max-voltage = <3400000>;
+ };
+
+ regulator-2p5 at 130 {
+ compatible = "fsl,anatop-regulator";
+ regulator-name = "vdd2p5";
+ regulator-min-microvolt = <2100000>;
+ regulator-max-microvolt = <2875000>;
+ regulator-always-on;
+ anatop-reg-offset = <0x130>;
+ anatop-vol-bit-shift = <8>;
+ anatop-vol-bit-width = <5>;
+ anatop-min-bit-val = <0>;
+ anatop-min-voltage = <2100000>;
+ anatop-max-voltage = <2875000>;
+ };
+
+ reg_arm: regulator-vddcore at 140 {
+ compatible = "fsl,anatop-regulator";
+ regulator-name = "cpu";
+ regulator-min-microvolt = <725000>;
+ regulator-max-microvolt = <1450000>;
+ regulator-always-on;
+ anatop-reg-offset = <0x140>;
+ anatop-vol-bit-shift = <0>;
+ anatop-vol-bit-width = <5>;
+ anatop-delay-reg-offset = <0x170>;
+ anatop-delay-bit-shift = <24>;
+ anatop-delay-bit-width = <2>;
+ anatop-min-bit-val = <1>;
+ anatop-min-voltage = <725000>;
+ anatop-max-voltage = <1450000>;
+ };
+
+ reg_pcie: regulator-vddpcie at 140 {
+ compatible = "fsl,anatop-regulator";
+ regulator-name = "vddpcie";
+ regulator-min-microvolt = <725000>;
+ regulator-max-microvolt = <1450000>;
+ anatop-reg-offset = <0x140>;
+ anatop-vol-bit-shift = <9>;
+ anatop-vol-bit-width = <5>;
+ anatop-delay-reg-offset = <0x170>;
+ anatop-delay-bit-shift = <26>;
+ anatop-delay-bit-width = <2>;
+ anatop-min-bit-val = <1>;
+ anatop-min-voltage = <725000>;
+ anatop-max-voltage = <1450000>;
+ };
+
+ reg_soc: regulator-vddsoc at 140 {
+ compatible = "fsl,anatop-regulator";
+ regulator-name = "vddsoc";
+ regulator-min-microvolt = <725000>;
+ regulator-max-microvolt = <1450000>;
+ regulator-always-on;
+ anatop-reg-offset = <0x140>;
+ anatop-vol-bit-shift = <18>;
+ anatop-vol-bit-width = <5>;
+ anatop-delay-reg-offset = <0x170>;
+ anatop-delay-bit-shift = <28>;
+ anatop-delay-bit-width = <2>;
+ anatop-min-bit-val = <1>;
+ anatop-min-voltage = <725000>;
+ anatop-max-voltage = <1450000>;
+ };
+ };
+
+ tempmon: tempmon {
+ compatible = "fsl,imx6sx-tempmon", "fsl,imx6q-tempmon";
+ interrupts = <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>;
+ fsl,tempmon = <&anatop>;
+ fsl,tempmon-data = <&ocotp>;
+ clocks = <&clks IMX6SX_CLK_PLL3_USB_OTG>;
+ };
+
+ usbphy1: usbphy at 020c9000 {
+ compatible = "fsl,imx6sx-usbphy", "fsl,imx23-usbphy";
+ reg = <0x020c9000 0x1000>;
+ interrupts = <GIC_SPI 44 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX6SX_CLK_USBPHY1>;
+ fsl,anatop = <&anatop>;
+ };
+
+ usbphy2: usbphy at 020ca000 {
+ compatible = "fsl,imx6sx-usbphy", "fsl,imx23-usbphy";
+ reg = <0x020ca000 0x1000>;
+ interrupts = <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX6SX_CLK_USBPHY2>;
+ fsl,anatop = <&anatop>;
+ };
+
+ snvs: snvs at 020cc000 {
+ compatible = "fsl,sec-v4.0-mon", "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 0x020cc000 0x4000>;
+
+ snvs-rtc-lp at 34 {
+ compatible = "fsl,sec-v4.0-mon-rtc-lp";
+ reg = <0x34 0x58>;
+ interrupts = <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>;
+ };
+ };
+
+ epit1: epit at 020d0000 {
+ reg = <0x020d0000 0x4000>;
+ interrupts = <GIC_SPI 56 IRQ_TYPE_LEVEL_HIGH>;
+ };
+
+ epit2: epit at 020d4000 {
+ reg = <0x020d4000 0x4000>;
+ interrupts = <GIC_SPI 57 IRQ_TYPE_LEVEL_HIGH>;
+ };
+
+ src: src at 020d8000 {
+ compatible = "fsl,imx6sx-src", "fsl,imx51-src";
+ reg = <0x020d8000 0x4000>;
+ interrupts = <GIC_SPI 91 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>;
+ #reset-cells = <1>;
+ };
+
+ gpc: gpc at 020dc000 {
+ compatible = "fsl,imx6sx-gpc", "fsl,imx6q-gpc";
+ reg = <0x020dc000 0x4000>;
+ interrupts = <GIC_SPI 89 IRQ_TYPE_LEVEL_HIGH>;
+ };
+
+ iomuxc: iomuxc at 020e0000 {
+ compatible = "fsl,imx6sx-iomuxc";
+ reg = <0x020e0000 0x4000>;
+ };
+
+ gpr: iomuxc-gpr at 020e4000 {
+ compatible = "fsl,imx6sx-iomuxc-gpr", "syscon";
+ reg = <0x020e4000 0x4000>;
+ };
+
+ sdma: sdma at 020ec000 {
+ compatible = "fsl,imx6sx-sdma";
+ reg = <0x020ec000 0x4000>;
+ interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX6SX_CLK_SDMA>,
+ <&clks IMX6SX_CLK_SDMA>;
+ clock-names = "ipg", "ahb";
+ #dma-cells = <3>;
+ };
+ };
+
+ aips2: aips-bus at 02100000 {
+ compatible = "fsl,aips-bus", "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ reg = <0x02100000 0x100000>;
+ ranges;
+
+ usbotg1: usb at 02184000 {
+ compatible = "fsl,imx6sx-usb", "fsl,imx27-usb";
+ reg = <0x02184000 0x200>;
+ interrupts = <GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX6SX_CLK_USBOH3>;
+ fsl,usbphy = <&usbphy1>;
+ fsl,usbmisc = <&usbmisc 0>;
+ fsl,anatop = <&anatop>;
+ status = "disabled";
+ };
+
+ usbotg2: usb at 02184200 {
+ compatible = "fsl,imx6sx-usb", "fsl,imx27-usb";
+ reg = <0x02184200 0x200>;
+ interrupts = <GIC_SPI 42 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX6SX_CLK_USBOH3>;
+ fsl,usbphy = <&usbphy2>;
+ fsl,usbmisc = <&usbmisc 1>;
+ status = "disabled";
+ };
+
+ usbh: usb at 02184400 {
+ compatible = "fsl,imx6sx-usb", "fsl,imx27-usb";
+ reg = <0x02184400 0x200>;
+ interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX6SX_CLK_USBOH3>;
+ fsl,usbmisc = <&usbmisc 2>;
+ phy_type = "hsic";
+ fsl,anatop = <&anatop>;
+ status = "disabled";
+ };
+
+ usbmisc: usbmisc at 02184800 {
+ #index-cells = <1>;
+ compatible = "fsl,imx6sx-usbmisc";
+ reg = <0x02184800 0x200>;
+ clocks = <&clks IMX6SX_CLK_USBOH3>;
+ };
+
+ fec1: ethernet at 02188000 {
+ compatible = "fsl,imx6sx-fec", "fsl,imx6q-fec";
+ reg = <0x02188000 0x4000>;
+ interrupts = <GIC_SPI 118 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 119 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX6SX_CLK_ENET>,
+ <&clks IMX6SX_CLK_ENET_AHB>,
+ <&clks IMX6SX_CLK_ENET_PTP>,
+ <&clks IMX6SX_CLK_ENET_REF>,
+ <&clks IMX6SX_CLK_ENET_PTP>;
+ clock-names = "ipg", "ahb", "ptp",
+ "enet_clk_ref", "enet_out";
+ status = "disabled";
+ };
+
+ mlb: mlb at 0218c000 {
+ reg = <0x0218c000 0x4000>;
+ interrupts = <GIC_SPI 53 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 126 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX6SX_CLK_MLB>;
+ status = "disabled";
+ };
+
+ usdhc1: usdhc at 02190000 {
+ compatible = "fsl,imx6sx-usdhc", "fsl,imx6sl-usdhc";
+ reg = <0x02190000 0x4000>;
+ interrupts = <GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX6SX_CLK_USDHC1>,
+ <&clks IMX6SX_CLK_USDHC1>,
+ <&clks IMX6SX_CLK_USDHC1>;
+ clock-names = "ipg", "ahb", "per";
+ bus-width = <4>;
+ status = "disabled";
+ };
+
+ usdhc2: usdhc at 02194000 {
+ compatible = "fsl,imx6sx-usdhc", "fsl,imx6sl-usdhc";
+ reg = <0x02194000 0x4000>;
+ interrupts = <GIC_SPI 23 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX6SX_CLK_USDHC2>,
+ <&clks IMX6SX_CLK_USDHC2>,
+ <&clks IMX6SX_CLK_USDHC2>;
+ clock-names = "ipg", "ahb", "per";
+ bus-width = <4>;
+ status = "disabled";
+ };
+
+ usdhc3: usdhc at 02198000 {
+ compatible = "fsl,imx6sx-usdhc", "fsl,imx6sl-usdhc";
+ reg = <0x02198000 0x4000>;
+ interrupts = <GIC_SPI 24 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX6SX_CLK_USDHC3>,
+ <&clks IMX6SX_CLK_USDHC3>,
+ <&clks IMX6SX_CLK_USDHC3>;
+ clock-names = "ipg", "ahb", "per";
+ bus-width = <4>;
+ status = "disabled";
+ };
+
+ usdhc4: usdhc at 0219c000 {
+ compatible = "fsl,imx6sx-usdhc", "fsl,imx6sl-usdhc";
+ reg = <0x0219c000 0x4000>;
+ interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX6SX_CLK_USDHC4>,
+ <&clks IMX6SX_CLK_USDHC4>,
+ <&clks IMX6SX_CLK_USDHC4>;
+ clock-names = "ipg", "ahb", "per";
+ bus-width = <4>;
+ status = "disabled";
+ };
+
+ i2c1: i2c at 021a0000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,imx6sx-i2c", "fsl,imx21-i2c";
+ reg = <0x021a0000 0x4000>;
+ interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX6SX_CLK_I2C1>;
+ status = "disabled";
+ };
+
+ i2c2: i2c at 021a4000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,imx6sx-i2c", "fsl,imx21-i2c";
+ reg = <0x021a4000 0x4000>;
+ interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX6SX_CLK_I2C2>;
+ status = "disabled";
+ };
+
+ i2c3: i2c at 021a8000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,imx6sx-i2c", "fsl,imx21-i2c";
+ reg = <0x021a8000 0x4000>;
+ interrupts = <GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX6SX_CLK_I2C3>;
+ status = "disabled";
+ };
+
+ mmdc: mmdc at 021b0000 {
+ compatible = "fsl,imx6sx-mmdc", "fsl,imx6q-mmdc";
+ reg = <0x021b0000 0x4000>;
+ };
+
+ fec2: ethernet at 021b4000 {
+ compatible = "fsl,imx6sx-fec";
+ reg = <0x021b4000 0x4000>;
+ interrupts = <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX6SX_CLK_ENET>,
+ <&clks IMX6SX_CLK_ENET_AHB>,
+ <&clks IMX6SX_CLK_ENET_PTP>,
+ <&clks IMX6SX_CLK_ENET2_REF_125M>,
+ <&clks IMX6SX_CLK_ENET_PTP>;
+ clock-names = "ipg", "ahb", "ptp",
+ "enet_clk_ref", "enet_out";
+ status = "disabled";
+ };
+
+ weim: weim at 021b8000 {
+ compatible = "fsl,imx6sx-weim", "fsl,imx6q-weim";
+ reg = <0x021b8000 0x4000>;
+ interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX6SX_CLK_EIM_SLOW>;
+ };
+
+ ocotp: ocotp at 021bc000 {
+ compatible = "fsl,imx6sx-ocotp", "syscon";
+ reg = <0x021bc000 0x4000>;
+ clocks = <&clks IMX6SX_CLK_OCOTP>;
+ };
+
+ sai1: sai at 021d4000 {
+ compatible = "fsl,imx6sx-sai";
+ reg = <0x021d4000 0x4000>;
+ interrupts = <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX6SX_CLK_SAI1_IPG>,
+ <&clks IMX6SX_CLK_SAI1>,
+ <&clks 0>, <&clks 0>;
+ clock-names = "bus", "mclk1", "mclk2", "mclk3";
+ dma-names = "rx", "tx";
+ dmas = <&sdma 31 23 0>, <&sdma 32 23 0>;
+ dma-source = <&gpr 0 15 0 16>;
+ status = "disabled";
+ };
+
+ audmux: audmux at 021d8000 {
+ compatible = "fsl,imx6sx-audmux", "fsl,imx31-audmux";
+ reg = <0x021d8000 0x4000>;
+ status = "disabled";
+ };
+
+ sai2: sai at 021dc000 {
+ compatible = "fsl,imx6sx-sai";
+ reg = <0x021dc000 0x4000>;
+ interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX6SX_CLK_SAI2_IPG>,
+ <&clks IMX6SX_CLK_SAI2>,
+ <&clks 0>, <&clks 0>;
+ clock-names = "bus", "mclk1", "mclk2", "mclk3";
+ dma-names = "rx", "tx";
+ dmas = <&sdma 33 23 0>, <&sdma 34 23 0>;
+ dma-source = <&gpr 0 17 0 18>;
+ status = "disabled";
+ };
+
+ qspi1: qspi at 021e0000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,imx6sx-qspi";
+ reg = <0x021e0000 0x4000>, <0x60000000 0x10000000>;
+ reg-names = "QuadSPI", "QuadSPI-memory";
+ interrupts = <GIC_SPI 107 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX6SX_CLK_QSPI1>,
+ <&clks IMX6SX_CLK_QSPI1>;
+ clock-names = "qspi_en", "qspi";
+ status = "disabled";
+ };
+
+ qspi2: qspi at 021e4000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,imx6sx-qspi";
+ reg = <0x021e4000 0x4000>, <0x70000000 0x10000000>;
+ reg-names = "QuadSPI", "QuadSPI-memory";
+ interrupts = <GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX6SX_CLK_QSPI2>,
+ <&clks IMX6SX_CLK_QSPI2>;
+ clock-names = "qspi_en", "qspi";
+ status = "disabled";
+ };
+
+ uart2: serial at 021e8000 {
+ compatible = "fsl,imx6sx-uart", "fsl,imx21-uart";
+ reg = <0x021e8000 0x4000>;
+ interrupts = <GIC_SPI 27 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX6SX_CLK_UART_IPG>,
+ <&clks IMX6SX_CLK_UART_SERIAL>;
+ clock-names = "ipg", "per";
+ dmas = <&sdma 27 4 0>, <&sdma 28 4 0>;
+ dma-names = "rx", "tx";
+ status = "disabled";
+ };
+
+ uart3: serial at 021ec000 {
+ compatible = "fsl,imx6sx-uart", "fsl,imx21-uart";
+ reg = <0x021ec000 0x4000>;
+ interrupts = <GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX6SX_CLK_UART_IPG>,
+ <&clks IMX6SX_CLK_UART_SERIAL>;
+ clock-names = "ipg", "per";
+ dmas = <&sdma 29 4 0>, <&sdma 30 4 0>;
+ dma-names = "rx", "tx";
+ status = "disabled";
+ };
+
+ uart4: serial at 021f0000 {
+ compatible = "fsl,imx6sx-uart", "fsl,imx21-uart";
+ reg = <0x021f0000 0x4000>;
+ interrupts = <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX6SX_CLK_UART_IPG>,
+ <&clks IMX6SX_CLK_UART_SERIAL>;
+ clock-names = "ipg", "per";
+ dmas = <&sdma 31 4 0>, <&sdma 32 4 0>;
+ dma-names = "rx", "tx";
+ status = "disabled";
+ };
+
+ uart5: serial at 021f4000 {
+ compatible = "fsl,imx6sx-uart", "fsl,imx21-uart";
+ reg = <0x021f4000 0x4000>;
+ interrupts = <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX6SX_CLK_UART_IPG>,
+ <&clks IMX6SX_CLK_UART_SERIAL>;
+ clock-names = "ipg", "per";
+ dmas = <&sdma 33 4 0>, <&sdma 34 4 0>;
+ dma-names = "rx", "tx";
+ status = "disabled";
+ };
+
+ i2c4: i2c at 021f8000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,imx6sx-i2c", "fsl,imx21-i2c";
+ reg = <0x021f8000 0x4000>;
+ interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX6SX_CLK_I2C4>;
+ status = "disabled";
+ };
+ };
+
+ aips3: aips-bus at 02200000 {
+ compatible = "fsl,aips-bus", "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ reg = <0x02200000 0x100000>;
+ ranges;
+
+ spba-bus at 02200000 {
+ compatible = "fsl,spba-bus", "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ reg = <0x02240000 0x40000>;
+ ranges;
+
+ csi1: csi at 02214000 {
+ reg = <0x02214000 0x4000>;
+ interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX6SX_CLK_DISPLAY_AXI>,
+ <&clks IMX6SX_CLK_CSI>,
+ <&clks IMX6SX_CLK_DCIC1>;
+ clock-names = "disp-axi", "csi_mclk", "dcic";
+ status = "disabled";
+ };
+
+ pxp: pxp at 02218000 {
+ reg = <0x02218000 0x4000>;
+ interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX6SX_CLK_PXP_AXI>,
+ <&clks IMX6SX_CLK_DISPLAY_AXI>;
+ clock-names = "pxp-axi", "disp-axi";
+ status = "disabled";
+ };
+
+ csi2: csi at 0221c000 {
+ reg = <0x0221c000 0x4000>;
+ interrupts = <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX6SX_CLK_DISPLAY_AXI>,
+ <&clks IMX6SX_CLK_CSI>,
+ <&clks IMX6SX_CLK_DCIC2>;
+ clock-names = "disp-axi", "csi_mclk", "dcic";
+ status = "disabled";
+ };
+
+ lcdif1: lcdif at 02220000 {
+ reg = <0x02220000 0x4000>;
+ interrupts = <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX6SX_CLK_LCDIF1_PIX>,
+ <&clks IMX6SX_CLK_LCDIF_APB>,
+ <&clks IMX6SX_CLK_DISPLAY_AXI>;
+ clock-names = "pix", "axi", "disp_axi";
+ status = "disabled";
+ };
+
+ lcdif2: lcdif at 02224000 {
+ reg = <0x02224000 0x4000>;
+ interrupts = <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX6SX_CLK_LCDIF2_PIX>,
+ <&clks IMX6SX_CLK_LCDIF_APB>,
+ <&clks IMX6SX_CLK_DISPLAY_AXI>;
+ clock-names = "pix", "axi", "disp_axi";
+ status = "disabled";
+ };
+
+ vadc: vadc at 02228000 {
+ reg = <0x02228000 0x4000>, <0x0222c000 0x4000>;
+ reg-names = "vadc-vafe", "vadc-vdec";
+ clocks = <&clks IMX6SX_CLK_VADC>,
+ <&clks IMX6SX_CLK_CSI>;
+ clock-names = "vadc", "csi";
+ status = "disabled";
+ };
+ };
+
+ adc1: adc at 02280000 {
+ compatible = "fsl,imx6sx-adc", "fsl,vf610-adc";
+ reg = <0x02280000 0x4000>;
+ interrupts = <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX6SX_CLK_IPG>;
+ clock-names = "adc";
+ status = "disabled";
+ };
+
+ adc2: adc at 02284000 {
+ compatible = "fsl,imx6sx-adc", "fsl,vf610-adc";
+ reg = <0x02284000 0x4000>;
+ interrupts = <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX6SX_CLK_IPG>;
+ clock-names = "adc";
+ status = "disabled";
+ };
+
+ wdog3: wdog at 02288000 {
+ compatible = "fsl,imx6sx-wdt", "fsl,imx21-wdt";
+ reg = <0x02288000 0x4000>;
+ interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX6SX_CLK_DUMMY>;
+ status = "disabled";
+ };
+
+ ecspi5: ecspi at 0228c000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,imx6sx-ecspi", "fsl,imx51-ecspi";
+ reg = <0x0228c000 0x4000>;
+ interrupts = <GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX6SX_CLK_ECSPI5>,
+ <&clks IMX6SX_CLK_ECSPI5>;
+ clock-names = "ipg", "per";
+ status = "disabled";
+ };
+
+ uart6: serial at 022a0000 {
+ compatible = "fsl,imx6sx-uart", "fsl,imx21-uart";
+ reg = <0x022a0000 0x4000>;
+ interrupts = <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX6SX_CLK_UART_IPG>,
+ <&clks IMX6SX_CLK_UART_SERIAL>;
+ clock-names = "ipg", "per";
+ dmas = <&sdma 0 4 0>, <&sdma 47 4 0>;
+ dma-names = "rx", "tx";
+ status = "disabled";
+ };
+
+ pwm5: pwm at 022a4000 {
+ compatible = "fsl,imx6sx-pwm", "fsl,imx27-pwm";
+ reg = <0x022a4000 0x4000>;
+ interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX6SX_CLK_PWM5>,
+ <&clks IMX6SX_CLK_PWM5>;
+ clock-names = "ipg", "per";
+ #pwm-cells = <2>;
+ };
+
+ pwm6: pwm at 022a8000 {
+ compatible = "fsl,imx6sx-pwm", "fsl,imx27-pwm";
+ reg = <0x022a8000 0x4000>;
+ interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX6SX_CLK_PWM6>,
+ <&clks IMX6SX_CLK_PWM6>;
+ clock-names = "ipg", "per";
+ #pwm-cells = <2>;
+ };
+
+ pwm7: pwm at 022ac000 {
+ compatible = "fsl,imx6sx-pwm", "fsl,imx27-pwm";
+ reg = <0x022ac000 0x4000>;
+ interrupts = <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX6SX_CLK_PWM7>,
+ <&clks IMX6SX_CLK_PWM7>;
+ clock-names = "ipg", "per";
+ #pwm-cells = <2>;
+ };
+
+ pwm8: pwm at 0022b0000 {
+ compatible = "fsl,imx6sx-pwm", "fsl,imx27-pwm";
+ reg = <0x0022b0000 0x4000>;
+ interrupts = <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX6SX_CLK_PWM8>,
+ <&clks IMX6SX_CLK_PWM8>;
+ clock-names = "ipg", "per";
+ #pwm-cells = <2>;
+ };
+ };
+
+ pcie: pcie at 0x08000000 {
+ compatible = "fsl,imx6sx-pcie", "snps,dw-pcie";
+ reg = <0x08ffc000 0x4000>; /* DBI */
+ #address-cells = <3>;
+ #size-cells = <2>;
+ device_type = "pci";
+ /* configuration space */
+ ranges = <0x00000800 0 0x08f00000 0x08f00000 0 0x00080000
+ /* downstream I/O */
+ 0x81000000 0 0 0x08f80000 0 0x00010000
+ /* non-prefetchable memory */
+ 0x82000000 0 0x08000000 0x08000000 0 0x00f00000>;
+ num-lanes = <1>;
+ interrupts = <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX6SX_CLK_PCIE_REF_125M>,
+ <&clks IMX6SX_CLK_PCIE_AXI>,
+ <&clks IMX6SX_CLK_LVDS1_OUT>,
+ <&clks IMX6SX_CLK_DISPLAY_AXI>;
+ clock-names = "pcie_ref_125m", "pcie_axi",
+ "lvds_gate", "display_axi";
+ status = "disabled";
+ };
+ };
+};
--
1.8.3.2
More information about the linux-arm-kernel
mailing list