[PATCH] mmc: dw_mmc: Make sure we don't get stuck when we get an error

Seungwon Jeon tgih.jun at samsung.com
Mon May 12 21:52:23 PDT 2014


Hi Doug,

On Tue, May 13, 2014, Doug Anderson wrote:
> Seungwon,
> 
> On Sat, May 10, 2014 at 7:11 AM, Seungwon Jeon <tgih.jun at samsung.com> wrote:
> > On Fri, May 09, 2014, Sonny Rao wrote:
> >> On Thu, May 8, 2014 at 2:42 AM, Yuvaraj Kumar <yuvaraj.cd at gmail.com> wrote:
> >> > Any comments on this patch?
> >> >
> >>
> >> I'll just add that without this fix, running the tuning loop for UHS
> >> modes is not reliable on dw_mmc because errors will happen and you
> >> will eventually hit this race and hang.  This can happen any time
> >> there is tuning like during boot or during resume from suspend.
> >>
> >> > On Thu, Mar 27, 2014 at 11:48 AM, Yuvaraj Kumar C D
> >> > <yuvaraj.cd at gmail.com> wrote:
> >> >> From: Doug Anderson <dianders at chromium.org>
> >> >>
> >> >> If we happened to get a data error at just the wrong time the dw_mmc
> >> >> driver could get into a state where it would never complete its
> >> >> request.  That would leave the caller just hanging there.
> >> >>
> >> >> We fix this two ways and both of the two fixes on their own appear to
> >> >> fix the problems we've seen:
> >> >>
> >> >> 1. Fix a race in the tasklet where the interrupt setting the data
> >> >>    error happens _just after_ we check for it, then we get a
> >> >>    EVENT_XFER_COMPLETE.  We fix this by repeating a bit of code.
> > I think repeating is not good approach to fix race.
> > In your case, XFER_COMPLETE preceded data error and DTO didn't come?
> > It seems strange case.
> > I want to know actual error value if you can reproduce.
> 
> XFER_COMPLETE didn't necessarily precede data error.  Imagine this scenario:
> 
> 1. Check for data error: nope
> 2. Interrupt happens and we get a data error and immediately xfer complete
> 3. Check for xfer complete: yup
> 
> That's the state that we are handling.
> 
> The system that dw_mmc uses where the interrupt handler has no locking
> makes it incredibly difficult to get things right.  Can you propose an
> alternate fix that would avoid the race?
Thank you for detailed scenario.
You're right.
Have you consider using spin_lock() in interrupt handler?
Then, we'll need to change spin_lock() to spin_lock_irqsave() in tasklet func.
And other locks in driver may need to be adjusted properly.

To return above scenario:
1. Check for data error: nope
2. Check for xfer complete: nope -> escape tasklet.
3. Interrupt happens and we get a data error and immediately xfer complete
4. Check for data error (Again in tasklet) : yup

How about this change?

Thanks,
Seungwon Jeon
> 
> 
> >> >> 2. Fix it so that if we detect that we've got an error in the "data
> >> >>    busy" state and we're not going to do anything else we end the
> >> >>    request and unblock anyone waiting.
> >> >>
> >> >> Signed-off-by: Doug Anderson <dianders at chromium.org>
> >> >> Signed-off-by: Yuvaraj Kumar C D <yuvaraj.cd at gmail.com>
> >> >> ---
> >> >>  drivers/mmc/host/dw_mmc.c |   47 +++++++++++++++++++++++++++++++++++++++++++++
> >> >>  1 file changed, 47 insertions(+)
> >> >>
> >> >> diff --git a/drivers/mmc/host/dw_mmc.c b/drivers/mmc/host/dw_mmc.c
> >> >> index 1d77431..4c589f1 100644
> >> >> --- a/drivers/mmc/host/dw_mmc.c
> >> >> +++ b/drivers/mmc/host/dw_mmc.c
> >> >> @@ -1300,6 +1300,14 @@ static void dw_mci_tasklet_func(unsigned long priv)
> >> >>                         /* fall through */
> >> >>
> >> >>                 case STATE_SENDING_DATA:
> >> >> +                       /*
> >> >> +                        * We could get a data error and never a transfer
> >> >> +                        * complete so we'd better check for it here.
> >> >> +                        *
> >> >> +                        * Note that we don't really care if we also got a
> >> >> +                        * transfer complete; stopping the DMA and sending an
> >> >> +                        * abort won't hurt.
> >> >> +                        */
> >> >>                         if (test_and_clear_bit(EVENT_DATA_ERROR,
> >> >>                                                &host->pending_events)) {
> >> >>                                 dw_mci_stop_dma(host);
> >> >> @@ -1313,7 +1321,29 @@ static void dw_mci_tasklet_func(unsigned long priv)
> >> >>                                 break;
> >> >>
> >> >>                         set_bit(EVENT_XFER_COMPLETE, &host->completed_events);
> >> >> +
> >> >> +                       /*
> >> >> +                        * Handle an EVENT_DATA_ERROR that might have shown up
> >> >> +                        * before the transfer completed.  This might not have
> >> >> +                        * been caught by the check above because the interrupt
> >> >> +                        * could have gone off between the previous check and
> >> >> +                        * the check for transfer complete.
> >> >> +                        *
> >> >> +                        * Technically this ought not be needed assuming we
> >> >> +                        * get a DATA_COMPLETE eventually (we'll notice the
> >> >> +                        * error and end the request), but it shouldn't hurt.
> >> >> +                        *
> >> >> +                        * This has the advantage of sending the stop command.
> >> >> +                        */
> >> >> +                       if (test_and_clear_bit(EVENT_DATA_ERROR,
> >> >> +                                              &host->pending_events)) {
> >> >> +                               dw_mci_stop_dma(host);
> >> >> +                               send_stop_abort(host, data);
> >> >> +                               state = STATE_DATA_ERROR;
> >> >> +                               break;
> >> >> +                       }
> >> >>                         prev_state = state = STATE_DATA_BUSY;
> >> >> +
> >> >>                         /* fall through */
> >> >>
> >> >>                 case STATE_DATA_BUSY:
> >> >> @@ -1336,6 +1366,23 @@ static void dw_mci_tasklet_func(unsigned long priv)
> >> >>                                 /* stop command for open-ended transfer*/
> >> >>                                 if (data->stop)
> >> >>                                         send_stop_abort(host, data);
> >> >> +                       } else {
> >> >> +                               /*
> >> >> +                                * If we don't have a command complete now we'll
> >> >> +                                * never get one since we just reset everything;
> >> >> +                                * better end the request.
> >> >> +                                *
> >> >> +                                * If we do have a command complete we'll fall
> >> >> +                                * through to the SENDING_STOP command and
> >> >> +                                * everything will be peachy keen.
> >> >> +                                *
> >> >> +                                * TODO: I guess we shouldn't send a stop?
> >> >> +                                */
> >> >> +                               if (!test_bit(EVENT_CMD_COMPLETE,
> >> >> +                                             &host->pending_events)) {
> >> >> +                                       dw_mci_request_end(host, mrq);
> >> >> +                                       goto unlock;
> >> >> +                               }
> > Can you explain what happens above?
> > What is it for?
> 
> This was an alternate fix for the above, but appears to actually hit
> in practice too.
> 
> Said another way: if we don't add the extra checking for
> EVENT_DATA_ERROR (above) we'll end up here.  ...and if we ever get
> into this "else" and don't do _something_ then we'll wedge forever.
> 
> -Doug
> --
> To unsubscribe from this list: send the line "unsubscribe linux-mmc" in
> the body of a message to majordomo at vger.kernel.org
> More majordomo info at  http://vger.kernel.org/majordomo-info.html




More information about the linux-arm-kernel mailing list