[PATCH v2] arm/dts: am335x-evmsk enable display and lcd panel support
Darren Etheridge
detheridge at ti.com
Fri May 9 11:49:14 PDT 2014
Add the necessary nodes to enable the LCD controller and the
LCD panel that is attached to the Texas Instruments AM335x
EVMSK platform. Also setup the necessary pin mux within the
DT file to drive the LCD connector and add the correct
pinmux settings for the lcd pins to be configured to when
the SoC goes into sleep state for the minimum power
consumption.
For the sleep mode LCD pin settings, MUX_MODE7 is chosen as
this corresponds to switching the pins into input GPIO's with
an internal pulldown. Which has been determined to offer the
lowest power solution vs leaving the pins configured in LCD
mode.
Signed-off-by: Darren Etheridge <detheridge at ti.com>
---
v2:
Fixed up the incorrect label ordering in the pinmux comments for LCD pins
16 through 23 as reported by Wolfram Sang <wsa at sang-engineering.com>
arch/arm/boot/dts/am335x-evmsk.dts | 105 +++++++++++++++++++++++++++++++++++++
1 file changed, 105 insertions(+)
diff --git a/arch/arm/boot/dts/am335x-evmsk.dts b/arch/arm/boot/dts/am335x-evmsk.dts
index ab23885..d99c1b1 100644
--- a/arch/arm/boot/dts/am335x-evmsk.dts
+++ b/arch/arm/boot/dts/am335x-evmsk.dts
@@ -138,12 +138,113 @@
"Headphone Jack", "HPLOUT",
"Headphone Jack", "HPROUT";
};
+
+ panel {
+ compatible = "ti,tilcdc,panel";
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&lcd_pins_default>;
+ pinctrl-1 = <&lcd_pins_sleep>;
+ status = "okay";
+ panel-info {
+ ac-bias = <255>;
+ ac-bias-intrpt = <0>;
+ dma-burst-sz = <16>;
+ bpp = <32>;
+ fdd = <0x80>;
+ sync-edge = <0>;
+ sync-ctrl = <1>;
+ raster-order = <0>;
+ fifo-th = <0>;
+ };
+ display-timings {
+ 480x272 {
+ hactive = <480>;
+ vactive = <272>;
+ hback-porch = <43>;
+ hfront-porch = <8>;
+ hsync-len = <4>;
+ vback-porch = <12>;
+ vfront-porch = <4>;
+ vsync-len = <10>;
+ clock-frequency = <9000000>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ };
+ };
+ };
};
&am33xx_pinmux {
pinctrl-names = "default";
pinctrl-0 = <&gpio_keys_s0 &clkout2_pin>;
+ lcd_pins_default: lcd_pins_default {
+ pinctrl-single,pins = <
+ 0x20 (PIN_OUTPUT | MUX_MODE1) /* gpmc_ad8.lcd_data23 */
+ 0x24 (PIN_OUTPUT | MUX_MODE1) /* gpmc_ad9.lcd_data22 */
+ 0x28 (PIN_OUTPUT | MUX_MODE1) /* gpmc_ad10.lcd_data21 */
+ 0x2c (PIN_OUTPUT | MUX_MODE1) /* gpmc_ad11.lcd_data20 */
+ 0x30 (PIN_OUTPUT | MUX_MODE1) /* gpmc_ad12.lcd_data19 */
+ 0x34 (PIN_OUTPUT | MUX_MODE1) /* gpmc_ad13.lcd_data18 */
+ 0x38 (PIN_OUTPUT | MUX_MODE1) /* gpmc_ad14.lcd_data17 */
+ 0x3c (PIN_OUTPUT | MUX_MODE1) /* gpmc_ad15.lcd_data16 */
+ 0xa0 (PIN_OUTPUT | MUX_MODE0) /* lcd_data0.lcd_data0 */
+ 0xa4 (PIN_OUTPUT | MUX_MODE0) /* lcd_data1.lcd_data1 */
+ 0xa8 (PIN_OUTPUT | MUX_MODE0) /* lcd_data2.lcd_data2 */
+ 0xac (PIN_OUTPUT | MUX_MODE0) /* lcd_data3.lcd_data3 */
+ 0xb0 (PIN_OUTPUT | MUX_MODE0) /* lcd_data4.lcd_data4 */
+ 0xb4 (PIN_OUTPUT | MUX_MODE0) /* lcd_data5.lcd_data5 */
+ 0xb8 (PIN_OUTPUT | MUX_MODE0) /* lcd_data6.lcd_data6 */
+ 0xbc (PIN_OUTPUT | MUX_MODE0) /* lcd_data7.lcd_data7 */
+ 0xc0 (PIN_OUTPUT | MUX_MODE0) /* lcd_data8.lcd_data8 */
+ 0xc4 (PIN_OUTPUT | MUX_MODE0) /* lcd_data9.lcd_data9 */
+ 0xc8 (PIN_OUTPUT | MUX_MODE0) /* lcd_data10.lcd_data10 */
+ 0xcc (PIN_OUTPUT | MUX_MODE0) /* lcd_data11.lcd_data11 */
+ 0xd0 (PIN_OUTPUT | MUX_MODE0) /* lcd_data12.lcd_data12 */
+ 0xd4 (PIN_OUTPUT | MUX_MODE0) /* lcd_data13.lcd_data13 */
+ 0xd8 (PIN_OUTPUT | MUX_MODE0) /* lcd_data14.lcd_data14 */
+ 0xdc (PIN_OUTPUT | MUX_MODE0) /* lcd_data15.lcd_data15 */
+ 0xe0 (PIN_OUTPUT | MUX_MODE0) /* lcd_vsync.lcd_vsync */
+ 0xe4 (PIN_OUTPUT | MUX_MODE0) /* lcd_hsync.lcd_hsync */
+ 0xe8 (PIN_OUTPUT | MUX_MODE0) /* lcd_pclk.lcd_pclk */
+ 0xec (PIN_OUTPUT | MUX_MODE0) /* lcd_ac_bias_en.lcd_ac_bias_en */
+ >;
+ };
+
+ lcd_pins_sleep: lcd_pins_sleep {
+ pinctrl-single,pins = <
+ 0x20 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpmc_ad8.lcd_data23 */
+ 0x24 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpmc_ad9.lcd_data22 */
+ 0x28 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpmc_ad10.lcd_data21 */
+ 0x2c (PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpmc_ad11.lcd_data20 */
+ 0x30 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpmc_ad12.lcd_data19 */
+ 0x34 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpmc_ad13.lcd_data18 */
+ 0x38 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpmc_ad14.lcd_data17 */
+ 0x3c (PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpmc_ad15.lcd_data16 */
+ 0xa0 (PULL_DISABLE | MUX_MODE7) /* lcd_data0.lcd_data0 */
+ 0xa4 (PULL_DISABLE | MUX_MODE7) /* lcd_data1.lcd_data1 */
+ 0xa8 (PULL_DISABLE | MUX_MODE7) /* lcd_data2.lcd_data2 */
+ 0xac (PULL_DISABLE | MUX_MODE7) /* lcd_data3.lcd_data3 */
+ 0xb0 (PULL_DISABLE | MUX_MODE7) /* lcd_data4.lcd_data4 */
+ 0xb4 (PULL_DISABLE | MUX_MODE7) /* lcd_data5.lcd_data5 */
+ 0xb8 (PULL_DISABLE | MUX_MODE7) /* lcd_data6.lcd_data6 */
+ 0xbc (PULL_DISABLE | MUX_MODE7) /* lcd_data7.lcd_data7 */
+ 0xc0 (PULL_DISABLE | MUX_MODE7) /* lcd_data8.lcd_data8 */
+ 0xc4 (PULL_DISABLE | MUX_MODE7) /* lcd_data9.lcd_data9 */
+ 0xc8 (PULL_DISABLE | MUX_MODE7) /* lcd_data10.lcd_data10 */
+ 0xcc (PULL_DISABLE | MUX_MODE7) /* lcd_data11.lcd_data11 */
+ 0xd0 (PULL_DISABLE | MUX_MODE7) /* lcd_data12.lcd_data12 */
+ 0xd4 (PULL_DISABLE | MUX_MODE7) /* lcd_data13.lcd_data13 */
+ 0xd8 (PULL_DISABLE | MUX_MODE7) /* lcd_data14.lcd_data14 */
+ 0xdc (PULL_DISABLE | MUX_MODE7) /* lcd_data15.lcd_data15 */
+ 0xe0 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* lcd_vsync.lcd_vsync */
+ 0xe4 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* lcd_hsync.lcd_hsync */
+ 0xe8 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* lcd_pclk.lcd_pclk */
+ 0xec (PIN_INPUT_PULLDOWN | MUX_MODE7) /* lcd_ac_bias_en.lcd_ac_bias_en */
+ >;
+ };
+
+
user_leds_s0: user_leds_s0 {
pinctrl-single,pins = <
0x10 (PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* gpmc_ad4.gpio1_4 */
@@ -560,3 +661,7 @@
ti,wire-config = <0x00 0x11 0x22 0x33>;
};
};
+
+&lcdc {
+ status = "okay";
+};
--
1.8.4
More information about the linux-arm-kernel
mailing list