[PATCH 3/4] OMAPDSS: panel-sharp-ls037v7dw01: add device tree support
Tony Lindgren
tony at atomide.com
Thu May 8 16:33:00 PDT 2014
* Tony Lindgren <tony at atomide.com> [140507 11:00]:
> * Tomi Valkeinen <tomi.valkeinen at ti.com> [140507 09:03]:
> > On 07/05/14 18:03, Tony Lindgren wrote:
> > >
> > > BTW, I'm also personally fine with all five gpios showing in a single
> > > gpios property, I'm not too exited about naming anything in DT..
> >
> > I don't have a strong opinion here. I don't have much experience with
> > DT, especially with making bindings compatible with other ones.
> >
> > I'd just forget the simple-panel, and have single gpio array.
>
> Well if it's a don't care flag for both of us, let's try to use
> the existing standard for simple-panel.txt and add mode-gpios
> property. I'll post a patch for that.
Here's an updated version using enable-gpios, reset-gpios and
mode-gpios. So it follows simple-panel.txt and adds mode-gpios
that's currently specific to this panel only.
Also updated for -EPROBE_DEFER handling, tested that by changing
one of the GPIOs to be a twl4030 GPIO.
Regards,
Tony
8<------------------
From: Tony Lindgren <tony at atomide.com>
Date: Mon, 28 Apr 2014 20:22:21 -0700
Subject: [PATCH] OMAPDSS: panel-sharp-ls037v7dw01: add device tree support
We can pass the GPIO configuration for ls037v7dw01 in a standard
gpios property.
Signed-off-by: Tony Lindgren <tony at atomide.com>
--- /dev/null
+++ b/Documentation/devicetree/bindings/panel/sharp,ls037v7dw01.txt
@@ -0,0 +1,56 @@
+SHARP LS037V7DW01 TFT-LCD panel
+
+Required properties:
+- compatible: should be "sharp,ls037v7dw01"
+
+Optional properties:
+- enable-gpios: a GPIO spec for the optional enable pin
+ this pin is the INI pin as specified in the LS037V7DW01.pdf file.
+- reset-gpios: a GPIO spec for the optional reset pin
+ this pin is the RESB pin as specified in the LS037V7DW01.pdf file.
+- mode-gpios: a GPIO
+ ordered MO, LR, and UD as specified in the LS037V7DW01.pdf file.
+
+This binding is compatible with the simple-panel binding, which is specified
+in simple-panel.txt in this directory.
+
+This panel can have zero to five GPIOs to configure
+to change configuration between QVGA and VGA mode
+and the scan direction. As these pins can be also
+configured with external pulls, all the GPIOs are
+considered optional with holes in the array.
+
+Example when connected to a omap2+ based device:
+
+ lcd0: display {
+ compatible = "sharp,ls037v7dw01";
+ power-supply = <&lcd_3v3>;
+ enable-gpios = <&gpio5 24 GPIO_ACTIVE_HIGH>; /* gpio152, lcd INI */
+ reset-gpios = <&gpio5 27 GPIO_ACTIVE_HIGH>; /* gpio155, lcd RESB */
+ mode-gpios = <&gpio5 26 GPIO_ACTIVE_HIGH /* gpio154, lcd MO */
+ &gpio1 2 GPIO_ACTIVE_HIGH /* gpio2, lcd LR */
+ &gpio1 3 GPIO_ACTIVE_HIGH>; /* gpio3, lcd UD */
+
+ panel-timing {
+ clock-frequency = <19200000>;
+ hback-porch = <28>;
+ hactive = <480>;
+ hfront-porch = <1>;
+ hsync-len = <2>;
+ vback-porch = <1>;
+ vactive = <640>;
+ vfront-porch = <1>;
+ vsync-len = <1>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <1>;
+ };
+
+ port {
+ lcd_in: endpoint {
+ remote-endpoint = <&dpi_out>;
+ };
+ };
+ };
+
--- a/drivers/video/fbdev/omap2/displays-new/panel-sharp-ls037v7dw01.c
+++ b/drivers/video/fbdev/omap2/displays-new/panel-sharp-ls037v7dw01.c
@@ -12,15 +12,19 @@
#include <linux/delay.h>
#include <linux/gpio.h>
#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_gpio.h>
#include <linux/platform_device.h>
#include <linux/slab.h>
-
+#include <linux/regulator/consumer.h>
+#include <video/of_display_timing.h>
#include <video/omapdss.h>
#include <video/omap-panel-data.h>
struct panel_drv_data {
struct omap_dss_device dssdev;
struct omap_dss_device *in;
+ struct regulator *vcc;
int data_lines;
@@ -95,7 +99,8 @@ static int sharp_ls_enable(struct omap_dss_device *dssdev)
if (omapdss_device_is_enabled(dssdev))
return 0;
- in->ops.dpi->set_data_lines(in, ddata->data_lines);
+ if (ddata->data_lines)
+ in->ops.dpi->set_data_lines(in, ddata->data_lines);
in->ops.dpi->set_timings(in, &ddata->videomode);
r = in->ops.dpi->enable(in);
@@ -240,6 +245,88 @@ static int sharp_ls_probe_pdata(struct platform_device *pdev)
if (PTR_ERR(ddata->ini_gpio) == -EPROBE_DEFER)
return -EPROBE_DEFER;
+ ddata->videomode = sharp_ls_timings;
+
+ return 0;
+}
+
+static struct gpio_desc *
+sharp_ls_get_gpio_of(struct device *dev, int index, int val, char *desc)
+{
+ struct gpio_desc *gpio;
+
+ gpio = devm_gpiod_get_index(dev, desc, index);
+ if (IS_ERR(gpio))
+ return gpio;
+
+ gpiod_direction_output(gpio, val);
+
+ return gpio;
+}
+
+static int sharp_ls_probe_of(struct platform_device *pdev)
+{
+ struct panel_drv_data *ddata = platform_get_drvdata(pdev);
+ struct device_node *node = pdev->dev.of_node;
+ struct omap_dss_device *in;
+ struct display_timing timing;
+ struct videomode vm;
+ int r;
+
+ ddata->vcc = devm_regulator_get(&pdev->dev, "envdd");
+ if (IS_ERR(ddata->vcc)) {
+ dev_err(&pdev->dev, "failed to get regulator\n");
+ return PTR_ERR(ddata->vcc);
+ }
+
+ r = regulator_enable(ddata->vcc);
+ if (r != 0) {
+ dev_err(&pdev->dev, "failed to enable regulator\n");
+ return r;
+ }
+
+ /* lcd INI */
+ ddata->ini_gpio = sharp_ls_get_gpio_of(&pdev->dev, 3, 0, "enable");
+ if (PTR_ERR(ddata->ini_gpio) == -EPROBE_DEFER)
+ return -EPROBE_DEFER;
+
+ /* lcd RESB */
+ ddata->resb_gpio = sharp_ls_get_gpio_of(&pdev->dev, 0, 0, "reset");
+ if (PTR_ERR(ddata->resb_gpio) == -EPROBE_DEFER)
+ return -EPROBE_DEFER;
+
+ /* lcd MO */
+ ddata->mo_gpio = sharp_ls_get_gpio_of(&pdev->dev, 0, 0, "mode");
+ if (PTR_ERR(ddata->mo_gpio) == -EPROBE_DEFER)
+ return -EPROBE_DEFER;
+
+ /* lcd LR */
+ ddata->lr_gpio = sharp_ls_get_gpio_of(&pdev->dev, 1, 1, "mode");
+ if (PTR_ERR(ddata->lr_gpio) == -EPROBE_DEFER)
+ return -EPROBE_DEFER;
+
+ /* lcd UD */
+ ddata->ud_gpio = sharp_ls_get_gpio_of(&pdev->dev, 2, 1, "mode");
+ if (PTR_ERR(ddata->ud_gpio) == -EPROBE_DEFER)
+ return -EPROBE_DEFER;
+
+ r = of_get_display_timing(node, "panel-timing", &timing);
+ if (r) {
+ dev_err(&pdev->dev, "failed to get video timing\n");
+ return r;
+ }
+
+ videomode_from_timing(&timing, &vm);
+ videomode_to_omap_video_timings(&vm, &ddata->videomode);
+
+ in = omapdss_of_find_source_for_first_ep(node);
+ if (IS_ERR(in)) {
+ dev_err(&pdev->dev, "failed to find video source\n");
+ return PTR_ERR(in);
+ }
+
+ ddata->in = in;
+
return 0;
}
@@ -259,12 +346,14 @@ static int sharp_ls_probe(struct platform_device *pdev)
r = sharp_ls_probe_pdata(pdev);
if (r)
return r;
+ } else if (pdev->dev.of_node) {
+ r = sharp_ls_probe_of(pdev);
+ if (r)
+ return r;
} else {
return -ENODEV;
}
- ddata->videomode = sharp_ls_timings;
-
dssdev = &ddata->dssdev;
dssdev->dev = &pdev->dev;
dssdev->driver = &sharp_ls_ops;
@@ -302,12 +391,20 @@ static int __exit sharp_ls_remove(struct platform_device *pdev)
return 0;
}
+static const struct of_device_id sharp_ls_of_match[] = {
+ { .compatible = "sharp,ls037v7dw01", },
+ {},
+};
+
+MODULE_DEVICE_TABLE(of, sharp_ls_of_match);
+
static struct platform_driver sharp_ls_driver = {
.probe = sharp_ls_probe,
.remove = __exit_p(sharp_ls_remove),
.driver = {
.name = "panel-sharp-ls037v7dw01",
.owner = THIS_MODULE,
+ .of_match_table = sharp_ls_of_match,
},
};
More information about the linux-arm-kernel
mailing list