[PATCH v4 10/15] clk: exynos5420: update clocks for FSYS and FSYS2 blocks

[Tomasz Figa]

Shaik,

On 06.05.2014 18:26, Shaik Ameer Basha wrote:
> This patch adds more clocks from FSYS and FSYS2 blocks
> and uses GATE_IP_* registers for gating IPs.
>
> Signed-off-by: Rahul Sharma <rahul.sharma at samsung.com>
> Signed-off-by: Shaik Ameer Basha <shaik.ameer at samsung.com>
> ---
>   drivers/clk/samsung/clk-exynos5420.c |   41 ++++++++++++++++++++++------------
>   1 file changed, 27 insertions(+), 14 deletions(-)
>
> diff --git a/drivers/clk/samsung/clk-exynos5420.c b/drivers/clk/samsung/clk-exynos5420.c
> index f0460b4..6d88ae2 100644
> --- a/drivers/clk/samsung/clk-exynos5420.c
> +++ b/drivers/clk/samsung/clk-exynos5420.c

[snip]

> @@ -736,12 +749,9 @@ static struct samsung_gate_clock exynos5420_gate_clks[] __initdata = {
>   	GATE(CLK_SCLK_USBPHY300, "sclk_usbphy300", "dout_usbphy300",
>   		GATE_TOP_SCLK_FSYS, 8, CLK_SET_RATE_PARENT, 0),
>   	GATE(CLK_SCLK_USBD300, "sclk_usbd300", "dout_usbd300",
> -		GATE_TOP_SCLK_FSYS, 9, CLK_SET_RATE_PARENT, 0),
> +		GATE_TOP_SCLK_FSYS, 9, CLK_IGNORE_UNUSED, 0),

Why CLK_IGNORE_UNUSED? Also CLK_SET_RATE_PARENT seems quite right for 
this clock.

>   	GATE(CLK_SCLK_USBD301, "sclk_usbd301", "dout_usbd301",
> -		GATE_TOP_SCLK_FSYS, 10, CLK_SET_RATE_PARENT, 0),
> -
> -	GATE(CLK_SCLK_USBD301, "sclk_unipro", "dout_unipro",
> -		SRC_MASK_FSYS, 24, CLK_SET_RATE_PARENT, 0),
> +		GATE_TOP_SCLK_FSYS, 10, CLK_IGNORE_UNUSED, 0),

Same here.

>
>   	/* Display */
>   	GATE(CLK_SCLK_FIMD1, "sclk_fimd1", "dout_fimd1",
> @@ -760,20 +770,23 @@ static struct samsung_gate_clock exynos5420_gate_clks[] __initdata = {
>   		GATE_TOP_SCLK_MAU, 0, CLK_SET_RATE_PARENT, 0),
>   	GATE(CLK_SCLK_MAUPCM0, "sclk_maupcm0", "dout_maupcm0",
>   		GATE_TOP_SCLK_MAU, 1, CLK_SET_RATE_PARENT, 0),
> -	/* FSYS */
> +
> +	/* FSYS Block */
>   	GATE(CLK_TSI, "tsi", "aclk200_fsys", GATE_BUS_FSYS0, 0, 0, 0),
>   	GATE(CLK_PDMA0, "pdma0", "aclk200_fsys", GATE_BUS_FSYS0, 1, 0, 0),
>   	GATE(CLK_PDMA1, "pdma1", "aclk200_fsys", GATE_BUS_FSYS0, 2, 0, 0),
>   	GATE(CLK_UFS, "ufs", "aclk200_fsys2", GATE_BUS_FSYS0, 3, 0, 0),
> -	GATE(CLK_RTIC, "rtic", "aclk200_fsys", GATE_BUS_FSYS0, 5, 0, 0),
> -	GATE(CLK_MMC0, "mmc0", "aclk200_fsys2", GATE_BUS_FSYS0, 12, 0, 0),
> -	GATE(CLK_MMC1, "mmc1", "aclk200_fsys2", GATE_BUS_FSYS0, 13, 0, 0),
> -	GATE(CLK_MMC2, "mmc2", "aclk200_fsys2", GATE_BUS_FSYS0, 14, 0, 0),
> +	GATE(CLK_RTIC, "rtic", "aclk200_fsys", GATE_IP_FSYS, 9, 0, 0),
> +	GATE(CLK_MMC0, "mmc0", "aclk200_fsys2", GATE_IP_FSYS, 12, 0, 0),
> +	GATE(CLK_MMC1, "mmc1", "aclk200_fsys2", GATE_IP_FSYS, 13, 0, 0),
> +	GATE(CLK_MMC2, "mmc2", "aclk200_fsys2", GATE_IP_FSYS, 14, 0, 0),
>   	GATE(CLK_SROMC, "sromc", "aclk200_fsys2",
> -			GATE_BUS_FSYS0, 19, CLK_IGNORE_UNUSED, 0),
> -	GATE(CLK_USBH20, "usbh20", "aclk200_fsys", GATE_BUS_FSYS0, 20, 0, 0),
> -	GATE(CLK_USBD300, "usbd300", "aclk200_fsys", GATE_BUS_FSYS0, 21, 0, 0),
> -	GATE(CLK_USBD301, "usbd301", "aclk200_fsys", GATE_BUS_FSYS0, 28, 0, 0),
> +			GATE_IP_FSYS, 17, CLK_IGNORE_UNUSED, 0),
> +	GATE(CLK_USBH20, "usbh20", "aclk200_fsys", GATE_IP_FSYS, 18, 0, 0),
> +	GATE(CLK_USBD300, "usbd300", "aclk200_fsys", GATE_IP_FSYS, 19, 0, 0),
> +	GATE(CLK_USBD301, "usbd301", "aclk200_fsys", GATE_IP_FSYS, 20, 0, 0),
> +	GATE(CLK_SCLK_UNIPRO, "sclk_unipro", "dout_unipro",
> +			GATE_IP_FSYS, 23, CLK_SET_RATE_PARENT, 0),

Gating an SCLK through an GATE_IP_* register looks a bit unusual. The 
original entry for this clock had SRC_MASK_FSYS register used. Also 
there is the GATE_TOP_SCLK_FSYS register, are you sure that there is no 
bit for this clock there?

Best regards,
Tomasz