[PATCH 1/2] ARM: dts: imx51-eukrea-mbimxsd51-baseboard: Add CAN support

[Fabio Estevam]

From: Fabio Estevam <fabio.estevam at freescale.com>

Add support for CAN based on a MPC2515 connected to ECSPI1.

Signed-off-by: Fabio Estevam <fabio.estevam at freescale.com>
---
Eric/Denis,

I don't have the hardware to test it. Please give it a test.

 .../boot/dts/imx51-eukrea-mbimxsd51-baseboard.dts  | 34 ++++++++++++++++++++++
 1 file changed, 34 insertions(+)

diff --git a/arch/arm/boot/dts/imx51-eukrea-mbimxsd51-baseboard.dts b/arch/arm/boot/dts/imx51-eukrea-mbimxsd51-baseboard.dts
index 8b1098e..f0067e9 100644
--- a/arch/arm/boot/dts/imx51-eukrea-mbimxsd51-baseboard.dts
+++ b/arch/arm/boot/dts/imx51-eukrea-mbimxsd51-baseboard.dts
@@ -86,6 +86,24 @@
 	status = "okay";
 };
 
+&ecspi1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ecspi1>;
+	fsl,spi-num-chipselects = <1>;
+	cs-gpios = <&gpio4 24 GPIO_ACTIVE_HIGH>;
+	status = "okay";
+
+	can0: can at 0 {
+		compatible = "microchip,mcp2515";
+		reg = <0>;
+		clocks = <&clks IMX5_CLK_OSC>;
+		spi-max-frequency = <1000000>;
+		spi-cs-high;
+		interrupt-parent = <&gpio1>;
+		interrupts = <1 IRQ_TYPE_EDGE_FALLING>;
+	};
+};
+
 &i2c1 {
 	tlv320aic23: codec at 1a {
 		compatible = "ti,tlv320aic23";
@@ -104,6 +122,22 @@
 			>;
 		};
 
+		pinctrl_ecspi1: ecspi1grp {
+			fsl,pins = <
+				MX51_PAD_CSPI1_MISO__ECSPI1_MISO	0x185
+				MX51_PAD_CSPI1_MOSI__ECSPI1_MOSI	0x185
+				MX51_PAD_CSPI1_SCLK__ECSPI1_SCLK	0x185
+				MX51_PAD_CSPI1_SS0__GPIO4_24		0x80000000 	/* CS0 */
+				MX51_PAD_CSI2_PIXCLK__GPIO4_15		0x80000000	/* nReset */
+				MX51_PAD_GPIO1_1__GPIO1_1		0x80000000	/* IRQ */
+				MX51_PAD_GPIO1_4__GPIO1_4		0x80000000	/* Control signals */
+				MX51_PAD_GPIO1_6__GPIO1_6		0x80000000
+				MX51_PAD_GPIO1_7__GPIO1_7		0x80000000
+				MX51_PAD_GPIO1_8__GPIO1_8		0x80000000
+				MX51_PAD_GPIO1_9__GPIO1_9		0x80000000
+			>;
+		};
+
 		pinctrl_esdhc1: esdhc1grp {
 			fsl,pins = <
 				MX51_PAD_SD1_CMD__SD1_CMD		0x400020d5
-- 
1.8.3.2