[PATCH 1/5] ARM: S5PV210: Remove camera support from mach-goni.c

[Kukjin Kim]

Sylwester Nawrocki wrote:
> 
> S5PV210 is going to get DT support, so we can remove the camera
> bits from the only board using camera on S5PV210. This allows to
> clean the exynos4-is driver by dropping code for non-dt platforms.
> This patch can be dropped if a patch removing the whole board
> file is applied first.
> 
> Signed-off-by: Sylwester Nawrocki <s.nawrocki at samsung.com>
> Acked-by: Kyungmin Park <kyungmin.park at samsung.com>

Hi Sylwester,

Cleanup is always welcome ;-)

I think, when this series is ready for mainline, this will be handled in
media tree. So,

Acked-by: Kukjin Kim <kgene.kim at samsung.com>

Thanks,
Kukjin

> ---
>  arch/arm/mach-s5pv210/mach-goni.c |   51
---------------------------------
> ----
>  1 file changed, 51 deletions(-)
> 
> diff --git a/arch/arm/mach-s5pv210/mach-goni.c b/arch/arm/mach-
> s5pv210/mach-goni.c
> index b41a38a..6c719ec 100644
> --- a/arch/arm/mach-s5pv210/mach-goni.c
> +++ b/arch/arm/mach-s5pv210/mach-goni.c
> @@ -49,11 +49,6 @@
>  #include <plat/clock.h>
>  #include <plat/samsung-time.h>
>  #include <plat/mfc.h>
> -#include <plat/camport.h>
> -
> -#include <media/v4l2-mediabus.h>
> -#include <media/s5p_fimc.h>
> -#include <media/noon010pc30.h>
> 
>  #include "common.h"
> 
> @@ -285,14 +280,6 @@ static void __init goni_tsp_init(void)
>  /* USB OTG */
>  static struct s3c_hsotg_plat goni_hsotg_pdata;
> 
> -static void goni_camera_init(void)
> -{
> -	s5pv210_fimc_setup_gpio(S5P_CAMPORT_A);
> -
> -	/* Set max driver strength on CAM_A_CLKOUT pin. */
> -	s5p_gpio_set_drvstr(S5PV210_GPE1(3), S5P_GPIO_DRVSTR_LV4);
> -}
> -
>  /* MAX8998 regulators */
>  #if defined(CONFIG_REGULATOR_MAX8998) ||
> defined(CONFIG_REGULATOR_MAX8998_MODULE)
> 
> @@ -825,34 +812,6 @@ static void goni_setup_sdhci(void)
>  	s3c_sdhci2_set_platdata(&goni_hsmmc2_data);
>  };
> 
> -static struct noon010pc30_platform_data noon010pc30_pldata = {
> -	.clk_rate	= 16000000UL,
> -	.gpio_nreset	= S5PV210_GPB(2), /* CAM_CIF_NRST */
> -	.gpio_nstby	= S5PV210_GPB(0), /* CAM_CIF_NSTBY */
> -};
> -
> -static struct i2c_board_info noon010pc30_board_info = {
> -	I2C_BOARD_INFO("NOON010PC30", 0x60 >> 1),
> -	.platform_data = &noon010pc30_pldata,
> -};
> -
> -static struct fimc_source_info goni_camera_sensors[] = {
> -	{
> -		.mux_id		= 0,
> -		.flags		= V4L2_MBUS_PCLK_SAMPLE_FALLING |
> -				  V4L2_MBUS_VSYNC_ACTIVE_LOW,
> -		.fimc_bus_type	= FIMC_BUS_TYPE_ITU_601,
> -		.board_info	= &noon010pc30_board_info,
> -		.i2c_bus_num	= 0,
> -		.clk_frequency	= 16000000UL,
> -	},
> -};
> -
> -static struct s5p_platform_fimc goni_fimc_md_platdata __initdata = {
> -	.source_info	= goni_camera_sensors,
> -	.num_clients	= ARRAY_SIZE(goni_camera_sensors),
> -};
> -
>  /* Audio device */
>  static struct platform_device goni_device_audio = {
>  	.name = "smdk-audio",
> @@ -874,10 +833,6 @@ static struct platform_device *goni_devices[]
> __initdata = {
>  	&s5p_device_mixer,
>  	&s5p_device_sdo,
>  	&s3c_device_i2c0,
> -	&s5p_device_fimc0,
> -	&s5p_device_fimc1,
> -	&s5p_device_fimc2,
> -	&s5p_device_fimc_md,
>  	&s3c_device_hsmmc0,
>  	&s3c_device_hsmmc1,
>  	&s3c_device_hsmmc2,
> @@ -946,14 +901,8 @@ static void __init goni_machine_init(void)
>  	/* FB */
>  	s3c_fb_set_platdata(&goni_lcd_pdata);
> 
> -	/* FIMC */
> -	s3c_set_platdata(&goni_fimc_md_platdata,
> sizeof(goni_fimc_md_platdata),
> -			 &s5p_device_fimc_md);
> -
>  	s3c_hsotg_set_platdata(&goni_hsotg_pdata);
> 
> -	goni_camera_init();
> -
>  	/* SPI */
>  	spi_register_board_info(spi_board_info, ARRAY_SIZE(spi_board_info));
> 
> --
> 1.7.9.5