[RFC 08/11] ARM: dts: am33xx: Add prcm_resets node

[Dan Murphy]

Tony

On 04/30/2014 05:33 PM, Tony Lindgren wrote:
> * Dan Murphy <dmurphy at ti.com> [140430 11:14]:
>> On 04/30/2014 01:10 PM, Tony Lindgren wrote:
>>> * Dan Murphy <dmurphy at ti.com> [140430 11:00]:
>>>> Tony and Arnd
>>>>
>>>> Thanks for the comments
>>>>
>>>> On 04/29/2014 07:22 PM, Tony Lindgren wrote:
>>>>> * Arnd Bergmann <arnd at arndb.de> [140429 13:35]:
>>>>>> On Tuesday 29 April 2014 15:19:47 Dan Murphy wrote:
>>>>>>> + * AM33xx reset index for PRCM Module
>>>>>>> + *
>>>>>>> + * Copyright 2014 Texas Instruments Inc.
>>>>>>> + *
>>>>>>> + * This program is free software; you can redistribute it and/or modify
>>>>>>> + * it under the terms of the GNU General Public License version 2 as
>>>>>>> + * published by the Free Software Foundation.
>>>>>>> + */
>>>>>>> +
>>>>>>> +#ifndef _DT_BINDINGS_RESET_TI_AM33XX_H
>>>>>>> +#define _DT_BINDINGS_RESET_TI_AM33XX_H
>>>>>>> +
>>>>>>> +#define RESET_DEVICE_RESET                     0
>>>>>>> +#define RESET_GFX_RESET                                1
>>>>>>> +#define RESET_PER_RESET                                2
>>>>>>> +
>>>>>>> +#endif
>>>>>> Interfaces like this should only be used if you can't use hardware
>>>>>> numbers, in general. If these numbers are in the data sheet, just
>>>>>> put them directly into the dts file, as we do for interrupt numbers,
>>>>>> gpio numbers, register offsets etc.
>>>>>>
>>>>>> If you have made them up to define an interface between the driver
>>>>>> and DT because there is no usable hardare ID, I'd suggest just using
>>>>>> a single file across all SoCs that have this driver, and have
>>>>>> a unified name space.
>>>>> Also, it's a bit unclear how the reset controller phandle is used
>>>>> referenced and used by the consumer device.. Maybe setting that up
>>>>> first in a Linux generic way is a good point starting point.
>>>>>
>>>>> Maybe something like this along the same way as clocks are set up
>>>>> (completely untested):
>>>>>
>>>>> &reset1 {
>>>>> 	iva_reset: reset1 {
>>>>> 		reg = /bits/ 8 <0>;
>>>>> 	};
>>>>> 	gfx_reset: reset1 {
>>>>> 		reg = /bits/ 8 <1>;
>>>>> 	};
>>>>> 	...
>>>>> };
>>>>>
>>>>> &iva {
>>>>> 	compatible = "ti,ivahd";
>>>>> 	resets = <&reset1 1>;
>>>>> 	...
>>>>> };
>>>> I had something very similar to this when I was developing this driver but moved away from this.
>>>>
>>>> Following the clocks implementation I had a separate dtsi for resets for each device and had the data defined like so
>>>> for each SoC.
>>>>
>>>> &prcm_resets {
>>>>        device_reset: device_reset {
>>>>                rstctrl_offs = <0x1104>;
>>>>                ctrl_bit-shift = <0>;
>>>>                rstst_offs      = <0x1114>;
>>>>                sts_bit-shift   = <0>;
>>>>        };
>>>>
>>>>        gpu_reset: gpu_reset {
>>>>                rstctrl_offs = <0x0D00>;
>>>>                ctrl_bit-shift = <3>;
>>>>                rstst_offs      = <0x0D0C>;
>>>>                sts_bit-shift = <5>;
>>>>        };
>>>> };
>>>>
>>>> And then any client interested in a specific reset driver would include this
>>>>
>>>> resets = <&prcm_resets &gpu_reset>;
>>>> reset-names = "gpu_reset";
>>>>
>>>> Our reset code would then retrieve the register data through the phandle instead of an index.
>>>>
>>>> Thoughts?
>>> Using phandles makes sense here because it avoids the indexing. Indexing
>>> has a problem of needing to be in sync with the .dts files and the
>>> device driver(s). Using an index also easily causes misuse of virtual
>>> indexes being added that no longer describe the hardware at all.
>> Thanks.  What about placing register data in the dts files?  Is there any issue with this concept?
> I don't have issues with that but others may. In this case it seems
> like you should get away just defining few different types of reset
> controllers without adding any any custom properties?
>
> In your example above, the rstctrl_offs should be just standard
> reg entry as an offset from the prcm_resets base address. Then you
> you only really need the bit shift and the type of the reset
> controller? And the type could be the compatible flag?

Well the only issue I have with declaring the reg with the standard dt entry
is I have two register offsets here.

I will have to see if I can do this per the standard.
I may have to have children called control and status and define the reg and bits that way.

Dan

> Regards,
>
> Tony
>


-- 
------------------
Dan Murphy