[RFC PATCH 01/12] phy: phy-omap-pipe3: Add support for PCIe PHY
Kishon Vijay Abraham I
kishon at ti.com
Wed Mar 26 09:57:41 EDT 2014
PCIe PHY uses an external pll instead of the internal pll used by SATA
and USB3. So added support in pipe3 PHY to use external pll
Signed-off-by: Kishon Vijay Abraham I <kishon at ti.com>
---
Documentation/devicetree/bindings/phy/ti-phy.txt | 8 +-
drivers/phy/phy-ti-pipe3.c | 99 +++++++++++++++++-----
2 files changed, 84 insertions(+), 23 deletions(-)
diff --git a/Documentation/devicetree/bindings/phy/ti-phy.txt b/Documentation/devicetree/bindings/phy/ti-phy.txt
index 788fb0f..e628a23 100644
--- a/Documentation/devicetree/bindings/phy/ti-phy.txt
+++ b/Documentation/devicetree/bindings/phy/ti-phy.txt
@@ -49,8 +49,8 @@ usb2phy at 4a0ad080 {
TI PIPE3 PHY
Required properties:
- - compatible: Should be "ti,phy-usb3" or "ti,phy-pipe3-sata".
- "ti,omap-usb3" is deprecated.
+ - compatible: Should be "ti,phy-usb3", "ti,phy-pipe3-sata" or
+ "ti,phy-pipe3-pcie. "ti,omap-usb3" is deprecated.
- reg : Address and length of the register set for the device.
- reg-names: The names of the register addresses corresponding to the registers
filled in "reg".
@@ -62,6 +62,10 @@ Required properties:
* "wkupclk" - wakeup clock.
* "sysclk" - system clock.
* "refclk" - reference clock.
+ * "dpll_ref" - external dpll ref clk
+ * "dpll_ref_m2" - external dpll ref clk
+ * "phy-div" - divider for apll
+ * "div-clk" - apll clock
Optional properties:
- ctrl-module : phandle of the control module used by PHY driver to power on
diff --git a/drivers/phy/phy-ti-pipe3.c b/drivers/phy/phy-ti-pipe3.c
index 5913676..d43019d 100644
--- a/drivers/phy/phy-ti-pipe3.c
+++ b/drivers/phy/phy-ti-pipe3.c
@@ -80,6 +80,7 @@ struct ti_pipe3 {
struct clk *wkupclk;
struct clk *sys_clk;
struct clk *refclk;
+ struct clk *div_clk;
struct pipe3_dpll_map *dpll_map;
};
@@ -215,6 +216,9 @@ static int ti_pipe3_init(struct phy *x)
u32 val;
int ret = 0;
+ if (of_device_is_compatible(phy->dev->of_node, "ti,phy-pipe3-pcie"))
+ return 0;
+
/* Bring it out of IDLE if it is IDLE */
val = ti_pipe3_readl(phy->pll_ctrl_base, PLL_CONFIGURATION2);
if (val & PLL_IDLE) {
@@ -238,8 +242,11 @@ static int ti_pipe3_exit(struct phy *x)
u32 val;
unsigned long timeout;
- /* SATA DPLL can't be powered down due to Errata i783 */
- if (of_device_is_compatible(phy->dev->of_node, "ti,phy-pipe3-sata"))
+ /* SATA DPLL can't be powered down due to Errata i783 and PCIe
+ * does not have internal DPLL
+ */
+ if (of_device_is_compatible(phy->dev->of_node, "ti,phy-pipe3-sata") ||
+ of_device_is_compatible(phy->dev->of_node, "ti,phy-pipe3-pcie"))
return 0;
/* Put DPLL in IDLE mode */
@@ -286,32 +293,41 @@ static int ti_pipe3_probe(struct platform_device *pdev)
struct device_node *control_node;
struct platform_device *control_pdev;
const struct of_device_id *match;
-
- match = of_match_device(of_match_ptr(ti_pipe3_id_table), &pdev->dev);
- if (!match)
- return -EINVAL;
+ struct clk *clk;
phy = devm_kzalloc(&pdev->dev, sizeof(*phy), GFP_KERNEL);
if (!phy) {
dev_err(&pdev->dev, "unable to alloc mem for TI PIPE3 PHY\n");
return -ENOMEM;
}
+ phy->dev = &pdev->dev;
- phy->dpll_map = (struct pipe3_dpll_map *)match->data;
- if (!phy->dpll_map) {
- dev_err(&pdev->dev, "no DPLL data\n");
- return -EINVAL;
- }
+ if (!of_device_is_compatible(node, "ti,phy-pipe3-pcie")) {
+ match = of_match_device(of_match_ptr(ti_pipe3_id_table),
+ &pdev->dev);
+ if (!match)
+ return -EINVAL;
- res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "pll_ctrl");
- phy->pll_ctrl_base = devm_ioremap_resource(&pdev->dev, res);
- if (IS_ERR(phy->pll_ctrl_base))
- return PTR_ERR(phy->pll_ctrl_base);
+ phy->dpll_map = (struct pipe3_dpll_map *)match->data;
+ if (!phy->dpll_map) {
+ dev_err(&pdev->dev, "no DPLL data\n");
+ return -EINVAL;
+ }
- phy->dev = &pdev->dev;
+ res = platform_get_resource_byname(pdev, IORESOURCE_MEM,
+ "pll_ctrl");
+ phy->pll_ctrl_base = devm_ioremap_resource(&pdev->dev, res);
+ if (IS_ERR(phy->pll_ctrl_base))
+ return PTR_ERR(phy->pll_ctrl_base);
- if (!of_device_is_compatible(node, "ti,phy-pipe3-sata")) {
+ phy->sys_clk = devm_clk_get(phy->dev, "sysclk");
+ if (IS_ERR(phy->sys_clk)) {
+ dev_err(&pdev->dev, "unable to get sysclk\n");
+ return -EINVAL;
+ }
+ }
+ if (!of_device_is_compatible(node, "ti,phy-pipe3-sata")) {
phy->wkupclk = devm_clk_get(phy->dev, "wkupclk");
if (IS_ERR(phy->wkupclk)) {
dev_err(&pdev->dev, "unable to get wkupclk\n");
@@ -328,10 +344,35 @@ static int ti_pipe3_probe(struct platform_device *pdev)
phy->refclk = ERR_PTR(-ENODEV);
}
- phy->sys_clk = devm_clk_get(phy->dev, "sysclk");
- if (IS_ERR(phy->sys_clk)) {
- dev_err(&pdev->dev, "unable to get sysclk\n");
- return -EINVAL;
+ if (of_device_is_compatible(node, "ti,phy-pipe3-pcie")) {
+ clk = devm_clk_get(phy->dev, "dpll_ref");
+ if (IS_ERR(clk)) {
+ dev_err(&pdev->dev, "unable to get dpll ref clk\n");
+ return PTR_ERR(clk);
+ }
+ clk_set_rate(clk, 1500000000);
+
+ clk = devm_clk_get(phy->dev, "dpll_ref_m2");
+ if (IS_ERR(clk)) {
+ dev_err(&pdev->dev, "unable to get dpll ref m2 clk\n");
+ return PTR_ERR(clk);
+ }
+ clk_set_rate(clk, 100000000);
+
+ clk = devm_clk_get(phy->dev, "phy-div");
+ if (IS_ERR(clk)) {
+ dev_err(&pdev->dev, "unable to get phy-div clk\n");
+ return PTR_ERR(clk);
+ }
+ clk_set_rate(clk, 100000000);
+
+ phy->div_clk = devm_clk_get(phy->dev, "div-clk");
+ if (IS_ERR(phy->div_clk)) {
+ dev_err(&pdev->dev, "unable to get div-clk\n");
+ return PTR_ERR(phy->div_clk);
+ }
+ } else {
+ phy->div_clk = ERR_PTR(-ENODEV);
}
control_node = of_parse_phandle(node, "ctrl-module", 0);
@@ -387,6 +428,8 @@ static int ti_pipe3_runtime_suspend(struct device *dev)
clk_disable_unprepare(phy->wkupclk);
if (!IS_ERR(phy->refclk))
clk_disable_unprepare(phy->refclk);
+ if (!IS_ERR(phy->div_clk))
+ clk_disable_unprepare(phy->div_clk);
return 0;
}
@@ -412,8 +455,19 @@ static int ti_pipe3_runtime_resume(struct device *dev)
}
}
+ if (!IS_ERR(phy->div_clk)) {
+ ret = clk_prepare_enable(phy->div_clk);
+ if (ret) {
+ dev_err(phy->dev, "Failed to enable div_clk %d\n", ret);
+ goto err3;
+ }
+ }
return 0;
+err3:
+ if (!IS_ERR(phy->wkupclk))
+ clk_disable_unprepare(phy->wkupclk);
+
err2:
if (!IS_ERR(phy->refclk))
clk_disable_unprepare(phy->refclk);
@@ -446,6 +500,9 @@ static const struct of_device_id ti_pipe3_id_table[] = {
.compatible = "ti,phy-pipe3-sata",
.data = dpll_map_sata,
},
+ {
+ .compatible = "ti,phy-pipe3-pcie",
+ },
{}
};
MODULE_DEVICE_TABLE(of, ti_pipe3_id_table);
--
1.7.9.5
More information about the linux-arm-kernel
mailing list