[PATCH v2 02/13] phy: omap-control: Update DT binding information

[Roger Quadros]

Move omap-control binding information to the right location.

Signed-off-by: Roger Quadros <rogerq at ti.com>
---
 Documentation/devicetree/bindings/phy/ti-phy.txt   | 25 ++++++++++++++++++++++
 Documentation/devicetree/bindings/usb/omap-usb.txt | 24 ---------------------
 2 files changed, 25 insertions(+), 24 deletions(-)

diff --git a/Documentation/devicetree/bindings/phy/ti-phy.txt b/Documentation/devicetree/bindings/phy/ti-phy.txt
index f671163..5c5b1b0 100644
--- a/Documentation/devicetree/bindings/phy/ti-phy.txt
+++ b/Documentation/devicetree/bindings/phy/ti-phy.txt
@@ -1,5 +1,30 @@
 TI PHY: DT DOCUMENTATION FOR PHYs in TI PLATFORMs
 
+OMAP CONTROL PHY
+
+Required properties:
+ - compatible: Should be one of
+ "ti,control-phy-otghs" - if it has otghs_control mailbox register as on OMAP4.
+ "ti,control-phy-usb2" - if it has Power down bit in control_dev_conf register
+                        e.g. USB2_PHY on OMAP5.
+ "ti,control-phy-pipe3" - if it has DPLL and individual Rx & Tx power control
+                        e.g. USB3 PHY and SATA PHY on OMAP5.
+ "ti,control-phy-dra7usb2" - if it has power down register like USB2 PHY on
+                        DRA7 platform.
+ "ti,control-phy-am437usb2" - if it has power down register like USB2 PHY on
+                        AM437 platform.
+ - reg : Address and length of the register set for the device. It contains
+   the address of "otghs_control" for control-phy-otghs or "power" register
+   for other types.
+ - reg-names: should be "otghs_control" control-phy-otghs and "power" for
+   other types.
+
+omap_control_usb: omap-control-usb at 4a002300 {
+        compatible = "ti,control-phy-otghs";
+        reg = <0x4a00233c 0x4>;
+        reg-names = "otghs_control";
+};
+
 OMAP USB2 PHY
 
 Required properties:
diff --git a/Documentation/devicetree/bindings/usb/omap-usb.txt b/Documentation/devicetree/bindings/usb/omap-usb.txt
index c495135..38b2fae 100644
--- a/Documentation/devicetree/bindings/usb/omap-usb.txt
+++ b/Documentation/devicetree/bindings/usb/omap-usb.txt
@@ -76,27 +76,3 @@ omap_dwc3 {
 	ranges;
 };
 
-OMAP CONTROL USB
-
-Required properties:
- - compatible: Should be one of
- "ti,control-phy-otghs" - if it has otghs_control mailbox register as on OMAP4.
- "ti,control-phy-usb2" - if it has Power down bit in control_dev_conf register
-			e.g. USB2_PHY on OMAP5.
- "ti,control-phy-pipe3" - if it has DPLL and individual Rx & Tx power control
-			e.g. USB3 PHY and SATA PHY on OMAP5.
- "ti,control-phy-dra7usb2" - if it has power down register like USB2 PHY on
-			DRA7 platform.
- "ti,control-phy-am437usb2" - if it has power down register like USB2 PHY on
-			AM437 platform.
- - reg : Address and length of the register set for the device. It contains
-   the address of "otghs_control" for control-phy-otghs or "power" register
-   for other types.
- - reg-names: should be "otghs_control" control-phy-otghs and "power" for
-   other types.
-
-omap_control_usb: omap-control-usb at 4a002300 {
-	compatible = "ti,control-phy-otghs";
-	reg = <0x4a00233c 0x4>;
-	reg-names = "otghs_control";
-};
-- 
1.8.3.2