[PATCH 02/12] phy: omap-control: Update DT binding information

[Tony Lindgren]

* Roger Quadros <rogerq at ti.com> [140305 04:26]:
> + George
> 
> Tony,
> 
> On 03/04/2014 06:28 PM, Tony Lindgren wrote:
> > * Roger Quadros <rogerq at ti.com> [140304 01:17]:
> >> Hi Tony,
> >>
> >> On 03/03/2014 09:02 PM, Tony Lindgren wrote:
> >>> * Roger Quadros <rogerq at ti.com> [140303 07:10]:
> >>>> Move omap-control binding information to the right location.
> >>>>
> >>>> Signed-off-by: Roger Quadros <rogerq at ti.com>
> >>>> ---
> >>>>  Documentation/devicetree/bindings/phy/ti-phy.txt   | 25 ++++++++++++++++++++++
> >>>>  Documentation/devicetree/bindings/usb/omap-usb.txt | 24 ---------------------
> >>>>  2 files changed, 25 insertions(+), 24 deletions(-)
> >>>>
> >>>> diff --git a/Documentation/devicetree/bindings/phy/ti-phy.txt b/Documentation/devicetree/bindings/phy/ti-phy.txt
> >>>> index 207e14c..41dc132 100644
> >>>> --- a/Documentation/devicetree/bindings/phy/ti-phy.txt
> >>>> +++ b/Documentation/devicetree/bindings/phy/ti-phy.txt
> >>>> @@ -1,5 +1,30 @@
> >>>>  TI PHY: DT DOCUMENTATION FOR PHYs in TI PLATFORMs
> >>>>  
> >>>> +OMAP CONTROL PHY
> >>>> +
> >>>> +Required properties:
> >>>> + - compatible: Should be one of
> >>>> + "ti,control-phy-otghs" - if it has otghs_control mailbox register as on OMAP4.
> >>>> + "ti,control-phy-usb2" - if it has Power down bit in control_dev_conf register
> >>>> +                        e.g. USB2_PHY on OMAP5.
> >>>> + "ti,control-phy-pipe3" - if it has DPLL and individual Rx & Tx power control
> >>>> +                        e.g. USB3 PHY and SATA PHY on OMAP5.
> >>>> + "ti,control-phy-dra7usb2" - if it has power down register like USB2 PHY on
> >>>> +                        DRA7 platform.
> >>>> + "ti,control-phy-am437usb2" - if it has power down register like USB2 PHY on
> >>>> +                        AM437 platform.
> >>>
> >>> To me it seems that you can leave out all the above. You can set these falgs
> >>> flags directly in the driver based on the compatible flag. Then just initialize
> >>> the .data in the driver based on the compatible flag.
> >>
> >> I'm not sure if I got you. A single platform can have different type of phys.
> >>
> >> e.g. OMAP5 has both usb2 and pipe3 PHYs,
> >> DRA7 has both pipe3 and usb2 PHYs, but this usb2 PHY is not compatible with OMAP5 one
> >> so we need a new compatible id for that.
> >>
> >> To add to the woes, the designers were creative enough to make another mutation to
> >> the USB2 PHY for AM437x, :(
> > 
> > Oh OK, in that case the compatible flag may not be enough for configuring the
> > various instances.
> >  
> >> What do you suggest the compatible ids should look like for these 5 types of PHY control?
> >> OTGHS	(OMAP4 & 5)
> >> USB2	(OMAP5)
> >> PIPE3	(OMAP5 & DRA7)
> >> USB2x	(DRA7)
> >> USB2y	(AM437)
> > 
> > I think in that case having the various instances fully configurable from
> > device tree is OK if you prefer that. But if you wanted to use the
> > compatible flag, then you could do something like this:
> > 
> > ti,control-phy-omap4-otghs	(assuming same on omap4 & 5)
> > ti,control-phy-omap5-usb2
> > ti,control-phy-omap5-pipe3	(assuming same on omap5 & dra7)
> > ti,control-phy-dra7-usb2x
> > ti,control-phy-am437-usb2y
> > ...
> > 
> 
> Please note that the original bindings were added in v3.13 and I'm just moving the documentation
> to the right location. So I don't think we should change the bindings now.

OK yeah if the bindings are established you should keep them around.
 
> "ti,control-phy-dra7usb2" and "ti,control-phy-am437usb2" have no users still so we could probably
> change those to "ti,control-phy-dra7-usb2" and "ti,control-phy-am437-usb2".
> 
> What do you say?

Makes sense to me.

Regards,

Tony