[PATCH 3/4] ARM: DT: STi: Add DT node for MiPHY365x

[Mark Rutland]

On Fri, Feb 14, 2014 at 11:23:55AM +0000, Lee Jones wrote:
> The MiPHY365x is a Generic PHY which can serve various SATA or PCIe
> devices. It has 2 ports which it can use for either; both SATA, both
> PCIe or one of each in any configuration.
> 
> Cc: devicetree at vger.kernel.org
> Cc: Srinivas Kandagatla <srinivas.kandagatla at st.com>
> Signed-off-by: Lee Jones <lee.jones at linaro.org>
> ---
>  arch/arm/boot/dts/stih416-b2020-revE.dts |  6 +++++-
>  arch/arm/boot/dts/stih416-b2020.dts      |  6 ++++++
>  arch/arm/boot/dts/stih416.dtsi           | 13 +++++++++++++
>  3 files changed, 24 insertions(+), 1 deletion(-)
> 
> diff --git a/arch/arm/boot/dts/stih416-b2020-revE.dts b/arch/arm/boot/dts/stih416-b2020-revE.dts
> index a874570..dbe67fa 100644
> --- a/arch/arm/boot/dts/stih416-b2020-revE.dts
> +++ b/arch/arm/boot/dts/stih416-b2020-revE.dts
> @@ -32,6 +32,10 @@
>  		ethernet1: ethernet at fef08000 {
>  			snps,reset-gpio 	= <&PIO0 7>;
>  		};
> -	};
>  
> +		miphy365x_phy: miphy365x at 0 {

This has registers at 0x0? Or is the unit-address wrong?

> +			st,pcie_tx_pol_inv = <1>;

This is a boolean. The '= <1>' is not required and is confusing.

> +			st,sata_gen = "gen3";

s/"gen3"/<3>/

Both these properties need s/_/-/ applied.

All these apply to the other dts too.

> +		};
> +	};
>  };
> diff --git a/arch/arm/boot/dts/stih416-b2020.dts b/arch/arm/boot/dts/stih416-b2020.dts
> index 276f28d..fd9cbad 100644
> --- a/arch/arm/boot/dts/stih416-b2020.dts
> +++ b/arch/arm/boot/dts/stih416-b2020.dts
> @@ -13,4 +13,10 @@
>  	model = "STiH416 B2020";
>  	compatible = "st,stih416", "st,stih416-b2020";

This compatible list is the wrong way around. Left to right should go
from most specific to most general / oldest variant.

>  
> +	soc {
> +		miphy365x_phy: miphy365x at 0 {

> +			st,pcie_tx_pol_inv = <1>;
> +			st,sata_gen = "gen3";
> +		};
> +	};
>  };
> diff --git a/arch/arm/boot/dts/stih416.dtsi b/arch/arm/boot/dts/stih416.dtsi
> index 85b8063..9fd8efb 100644
> --- a/arch/arm/boot/dts/stih416.dtsi
> +++ b/arch/arm/boot/dts/stih416.dtsi
> @@ -9,6 +9,8 @@
>  #include "stih41x.dtsi"
>  #include "stih416-clock.dtsi"
>  #include "stih416-pinctrl.dtsi"
> +
> +#include <dt-bindings/phy/phy-miphy365x.h>
>  #include <dt-bindings/interrupt-controller/arm-gic.h>
>  #include <dt-bindings/reset-controller/stih416-resets.h>
>  / {
> @@ -140,5 +142,16 @@
>  			clocks		= <&CLK_S_ICN_REG_0>;
>  		};
>  
> +		miphy365x_phy: miphy365x at 0 {

The unit-address should be fe382000 rather than 0 to match the first reg
entry.

Cheers,
Mark.

> +			compatible      = "st,miphy365x-phy";
> +			reg        	= <0xfe382000 0x100>,
> +					  <0xfe38a000 0x100>,
> +					  <0xfe394000 0x100>,
> +					  <0xfe804000 0x100>;
> +			reg-names  	= "sata0", "sata1", "pcie0", "pcie1";
> +
> +			#phy-cells 	= <2>;
> +			st,syscfg  	= <&syscfg_rear>;
> +		};
>  	};
>  };
> -- 
> 1.8.3.2
> 
> --
> To unsubscribe from this list: send the line "unsubscribe devicetree" in
> the body of a message to majordomo at vger.kernel.org
> More majordomo info at  http://vger.kernel.org/majordomo-info.html
>