[PATCH 3/5] phy: miphy365x: Provide support for the MiPHY356x Generic PHY
Lee Jones
lee.jones at linaro.org
Mon Jun 30 06:01:55 PDT 2014
The MiPHY365x is a Generic PHY which can serve various SATA or PCIe
devices. It has 2 ports which it can use for either; both SATA, both
PCIe or one of each in any configuration.
Acked-by: Kishon Vijay Abraham I <kishon at ti.com>
Acked-by: Mark Rutland <mark.rutland at arm.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue at st.com>
Signed-off-by: Lee Jones <lee.jones at linaro.org>
---
drivers/phy/Kconfig | 10 +
drivers/phy/Makefile | 1 +
drivers/phy/phy-miphy365x.c | 630 ++++++++++++++++++++++++++++++++++++++++++++
3 files changed, 641 insertions(+)
create mode 100644 drivers/phy/phy-miphy365x.c
diff --git a/drivers/phy/Kconfig b/drivers/phy/Kconfig
index 16a2f06..5d54dcf 100644
--- a/drivers/phy/Kconfig
+++ b/drivers/phy/Kconfig
@@ -31,6 +31,16 @@ config PHY_MVEBU_SATA
depends on OF
select GENERIC_PHY
+config PHY_MIPHY365X
+ tristate "STMicroelectronics MIPHY365X PHY driver for STiH41x series"
+ depends on ARCH_STI
+ depends on GENERIC_PHY
+ depends on HAS_IOMEM
+ depends on OF
+ help
+ Enable this to support the miphy transceiver (for SATA/PCIE)
+ that is part of STMicroelectronics STiH41x SoC series.
+
config OMAP_CONTROL_PHY
tristate "OMAP CONTROL PHY Driver"
depends on ARCH_OMAP2PLUS || COMPILE_TEST
diff --git a/drivers/phy/Makefile b/drivers/phy/Makefile
index b4f1d57..4602f67 100644
--- a/drivers/phy/Makefile
+++ b/drivers/phy/Makefile
@@ -7,6 +7,7 @@ obj-$(CONFIG_BCM_KONA_USB2_PHY) += phy-bcm-kona-usb2.o
obj-$(CONFIG_PHY_EXYNOS_DP_VIDEO) += phy-exynos-dp-video.o
obj-$(CONFIG_PHY_EXYNOS_MIPI_VIDEO) += phy-exynos-mipi-video.o
obj-$(CONFIG_PHY_MVEBU_SATA) += phy-mvebu-sata.o
+obj-$(CONFIG_PHY_MIPHY365X) += phy-miphy365x.o
obj-$(CONFIG_OMAP_CONTROL_PHY) += phy-omap-control.o
obj-$(CONFIG_OMAP_USB2) += phy-omap-usb2.o
obj-$(CONFIG_TI_PIPE3) += phy-ti-pipe3.o
diff --git a/drivers/phy/phy-miphy365x.c b/drivers/phy/phy-miphy365x.c
new file mode 100644
index 0000000..1109f42
--- /dev/null
+++ b/drivers/phy/phy-miphy365x.c
@@ -0,0 +1,630 @@
+/*
+ * Copyright (C) 2014 STMicroelectronics
+ *
+ * STMicroelectronics PHY driver MiPHY365 (for SoC STiH416).
+ *
+ * Author: Alexandre Torgue <alexandre.torgue at st.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2, as
+ * published by the Free Software Foundation.
+ *
+ */
+
+#include <linux/platform_device.h>
+#include <linux/io.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_platform.h>
+#include <linux/clk.h>
+#include <linux/phy/phy.h>
+#include <linux/delay.h>
+#include <linux/mfd/syscon.h>
+#include <linux/regmap.h>
+
+#include <dt-bindings/phy/phy-miphy365x.h>
+
+#define HFC_TIMEOUT 50
+
+#define SYSCFG_2521 0x824
+#define SYSCFG_2522 0x828
+#define SYSCFG_PCIE_SATA_MASK BIT(1)
+#define SYSCFG_PCIE_SATA_POS 1
+
+/* MiPHY365x register definitiona */
+#define RESET_REG 0x00
+#define RST_PLL BIT(1)
+#define RST_PLL_CAL BIT(2)
+#define RST_RX BIT(4)
+#define RST_MACRO BIT(7)
+
+#define STATUS_REG 0x01
+#define IDLL_RDY BIT(0)
+#define PLL_RDY BIT(1)
+#define DES_BIT_LOCK BIT(2)
+#define DES_SYMBOL_LOCK BIT(3)
+
+#define CTRL_REG 0x02
+#define TERM_EN BIT(0)
+#define PCI_EN BIT(2)
+#define DES_BIT_LOCK_EN BIT(3)
+#define TX_POL BIT(5)
+
+#define INT_CTRL_REG 0x03
+
+#define BOUNDARY1_REG 0x10
+#define SPDSEL_SEL BIT(0)
+
+#define BOUNDARY3_REG 0x12
+#define TX_SPDSEL_GEN1_VAL 0
+#define TX_SPDSEL_GEN2_VAL 0x01
+#define TX_SPDSEL_GEN3_VAL 0x02
+#define RX_SPDSEL_GEN1_VAL 0
+#define RX_SPDSEL_GEN2_VAL (0x01 << 3)
+#define RX_SPDSEL_GEN3_VAL (0x02 << 3)
+
+#define PCIE_REG 0x16
+
+#define BUF_SEL_REG 0x20
+#define CONF_GEN_SEL_GEN3 0x02
+#define CONF_GEN_SEL_GEN2 0x01
+#define PD_VDDTFILTER BIT(4)
+
+#define TXBUF1_REG 0x21
+#define SWING_VAL 0x04
+#define SWING_VAL_GEN1 0x03
+#define PREEMPH_VAL (0x3 << 5)
+
+#define TXBUF2_REG 0x22
+#define TXSLEW_VAL 0x2
+#define TXSLEW_VAL_GEN1 0x4
+
+#define RXBUF_OFFSET_CTRL_REG 0x23
+
+#define RXBUF_REG 0x25
+#define SDTHRES_VAL 0x01
+#define EQ_ON3 (0x03 << 4)
+#define EQ_ON1 (0x01 << 4)
+
+#define COMP_CTRL1_REG 0x40
+#define START_COMSR BIT(0)
+#define START_COMZC BIT(1)
+#define COMSR_DONE BIT(2)
+#define COMZC_DONE BIT(3)
+#define COMP_AUTO_LOAD BIT(4)
+
+#define COMP_CTRL2_REG 0x41
+#define COMP_2MHZ_RAT_GEN1 0x1e
+#define COMP_2MHZ_RAT 0xf
+
+#define COMP_CTRL3_REG 0x42
+#define COMSR_COMP_REF 0x33
+
+#define COMP_IDLL_REG 0x47
+#define COMZC_IDLL 0x2a
+
+#define PLL_CTRL1_REG 0x50
+#define PLL_START_CAL BIT(0)
+#define BUF_EN BIT(2)
+#define SYNCHRO_TX BIT(3)
+#define SSC_EN BIT(6)
+#define CONFIG_PLL BIT(7)
+
+#define PLL_CTRL2_REG 0x51
+#define BYPASS_PLL_CAL BIT(1)
+
+#define PLL_RAT_REG 0x52
+
+#define PLL_SSC_STEP_MSB_REG 0x56
+#define PLL_SSC_STEP_MSB_VAL 0x03
+
+#define PLL_SSC_STEP_LSB_REG 0x57
+#define PLL_SSC_STEP_LSB_VAL 0x63
+
+#define PLL_SSC_PER_MSB_REG 0x58
+#define PLL_SSC_PER_MSB_VAL 0
+
+#define PLL_SSC_PER_LSB_REG 0x59
+#define PLL_SSC_PER_LSB_VAL 0xf1
+
+#define IDLL_TEST_REG 0x72
+#define START_CLK_HF BIT(6)
+
+#define DES_BITLOCK_REG 0x86
+#define BIT_LOCK_LEVEL 0x01
+#define BIT_LOCK_CNT_512 (0x03 << 5)
+
+static u8 ports[] = { MIPHY_PORT_0, MIPHY_PORT_1 };
+
+struct miphy365x {
+ struct phy *phy;
+ void __iomem *base;
+ void __iomem *sata;
+ void __iomem *pcie;
+ u8 type;
+ u8 port;
+};
+
+struct miphy365x_dev {
+ struct device *dev;
+ struct mutex miphy_mutex;
+ struct miphy365x phys[ARRAY_SIZE(ports)];
+ bool pcie_tx_pol_inv;
+ bool sata_tx_pol_inv;
+ u32 sata_gen;
+ struct regmap *regmap;
+};
+
+/*
+ * These values are represented in Device tree. They are considered to be ABI
+ * and although they can be extended any existing values must not change.
+ */
+enum miphy_sata_gen {
+ SATA_GEN1 = 1,
+ SATA_GEN2,
+ SATA_GEN3
+};
+
+static u8 rx_tx_spd[] = {
+ TX_SPDSEL_GEN1_VAL | RX_SPDSEL_GEN1_VAL,
+ TX_SPDSEL_GEN2_VAL | RX_SPDSEL_GEN2_VAL,
+ TX_SPDSEL_GEN3_VAL | RX_SPDSEL_GEN3_VAL
+};
+
+#define miphy365x_phy_to_dev(inst) \
+ container_of((inst), struct miphy365x_dev, phys[(inst)->port]);
+
+/*
+ * This function selects the system configuration,
+ * either two SATA, one SATA and one PCIe, or two PCIe lanes.
+ */
+static int miphy365x_set_path(struct miphy365x *miphy_phy,
+ struct miphy365x_dev *miphy_dev)
+{
+ u8 config = miphy_phy->type | miphy_phy->port;
+ u32 mask = SYSCFG_PCIE_SATA_MASK;
+ u32 reg;
+ bool sata;
+
+ switch (config) {
+ case MIPHY_SATA_PORT0:
+ reg = SYSCFG_2521;
+ sata = true;
+ break;
+ case MIPHY_PCIE_PORT1:
+ reg = SYSCFG_2522;
+ sata = false;
+ break;
+ default:
+ dev_err(miphy_dev->dev, "Configuration not supported\n");
+ return -EINVAL;
+ }
+
+ return regmap_update_bits(miphy_dev->regmap, reg, mask,
+ sata << SYSCFG_PCIE_SATA_POS);
+}
+
+static void miphy365x_init_pcie_port(struct miphy365x *miphy_phy,
+ struct miphy365x_dev *miphy_dev)
+{
+ u8 val;
+
+ if (!miphy_dev->pcie_tx_pol_inv)
+ return;
+
+ /* Invert Tx polarity and clear pci_txdetect_pol bit */
+ val = TERM_EN | PCI_EN | DES_BIT_LOCK_EN | TX_POL;
+ writeb_relaxed(val, miphy_phy->base + CTRL_REG);
+ writeb_relaxed(0x00, miphy_phy->base + PCIE_REG);
+}
+
+static inline int miphy365x_hfc_not_rdy(struct miphy365x *miphy_phy,
+ struct miphy365x_dev *miphy_dev)
+{
+ int timeout = HFC_TIMEOUT;
+ u8 mask = IDLL_RDY | PLL_RDY;
+ u8 regval;
+
+ do {
+ regval = readb_relaxed(miphy_phy->base + STATUS_REG);
+ usleep_range(2000, 2500);
+ } while (timeout-- && (regval & mask));
+
+ if (timeout < 0) {
+ dev_err(miphy_dev->dev, "HFC ready timeout!\n");
+ return -EBUSY;
+ }
+
+ return 0;
+}
+
+static inline int miphy365x_rdy(struct miphy365x *miphy_phy,
+ struct miphy365x_dev *miphy_dev)
+{
+ int timeout = HFC_TIMEOUT;
+ u8 mask = IDLL_RDY | PLL_RDY;
+ u8 regval;
+
+ do {
+ regval = readb_relaxed(miphy_phy->base + STATUS_REG);
+ usleep_range(2000, 2500);
+ } while (timeout-- && ((regval & mask) != mask));
+
+ if (timeout < 0) {
+ dev_err(miphy_dev->dev, "PHY not ready timeout!\n");
+ return -EBUSY;
+ }
+
+ return 0;
+}
+
+static inline void miphy365x_set_comp(struct miphy365x *miphy_phy,
+ struct miphy365x_dev *miphy_dev)
+{
+ u8 val, mask;
+
+ if (miphy_dev->sata_gen == SATA_GEN1)
+ writeb_relaxed(COMP_2MHZ_RAT_GEN1,
+ miphy_phy->base + COMP_CTRL2_REG);
+ else
+ writeb_relaxed(COMP_2MHZ_RAT,
+ miphy_phy->base + COMP_CTRL2_REG);
+
+ if (miphy_dev->sata_gen != SATA_GEN3) {
+ writeb_relaxed(COMSR_COMP_REF,
+ miphy_phy->base + COMP_CTRL3_REG);
+ /*
+ * Force VCO current to value defined by address 0x5A
+ * and disable PCIe100Mref bit
+ * Enable auto load compensation for pll_i_bias
+ */
+ writeb_relaxed(BYPASS_PLL_CAL, miphy_phy->base + PLL_CTRL2_REG);
+ writeb_relaxed(COMZC_IDLL, miphy_phy->base + COMP_IDLL_REG);
+ }
+
+ /*
+ * Force restart compensation and enable auto load
+ * for Comzc_Tx, Comzc_Rx and Comsr on macro
+ */
+ val = START_COMSR | START_COMZC | COMP_AUTO_LOAD;
+ writeb_relaxed(val, miphy_phy->base + COMP_CTRL1_REG);
+
+ mask = COMSR_DONE | COMZC_DONE;
+ while ((readb_relaxed(miphy_phy->base + COMP_CTRL1_REG) & mask) != mask)
+ cpu_relax();
+}
+
+static inline void miphy365x_set_ssc(struct miphy365x *miphy_phy,
+ struct miphy365x_dev *miphy_dev)
+{
+ u8 val;
+
+ /*
+ * SSC Settings. SSC will be enabled through Link
+ * SSC Ampl. = 0.4%
+ * SSC Freq = 31KHz
+ */
+ writeb_relaxed(PLL_SSC_STEP_MSB_VAL,
+ miphy_phy->base + PLL_SSC_STEP_MSB_REG);
+ writeb_relaxed(PLL_SSC_STEP_LSB_VAL,
+ miphy_phy->base + PLL_SSC_STEP_LSB_REG);
+ writeb_relaxed(PLL_SSC_PER_MSB_VAL,
+ miphy_phy->base + PLL_SSC_PER_MSB_REG);
+ writeb_relaxed(PLL_SSC_PER_LSB_VAL,
+ miphy_phy->base + PLL_SSC_PER_LSB_REG);
+
+ /* SSC Settings complete */
+ if (miphy_dev->sata_gen == SATA_GEN1) {
+ val = PLL_START_CAL | BUF_EN | SYNCHRO_TX | CONFIG_PLL;
+ writeb_relaxed(val, miphy_phy->base + PLL_CTRL1_REG);
+ } else {
+ val = SSC_EN | PLL_START_CAL | BUF_EN | SYNCHRO_TX | CONFIG_PLL;
+ writeb_relaxed(val, miphy_phy->base + PLL_CTRL1_REG);
+ }
+}
+
+static int miphy365x_init_sata_port(struct miphy365x *miphy_phy,
+ struct miphy365x_dev *miphy_dev)
+{
+ int ret;
+ u8 val;
+
+ /*
+ * Force PHY macro reset, PLL calibration reset, PLL reset
+ * and assert Deserializer Reset
+ */
+ val = RST_PLL | RST_PLL_CAL | RST_RX | RST_MACRO;
+ writeb_relaxed(val, miphy_phy->base + RESET_REG);
+
+ if (miphy_dev->sata_tx_pol_inv)
+ writeb_relaxed(TX_POL, miphy_phy->base + CTRL_REG);
+
+ /*
+ * Force macro1 to use rx_lspd, tx_lspd
+ * Force Rx_Clock on first I-DLL phase
+ * Force Des in HP mode on macro, rx_lspd, tx_lspd for Gen2/3
+ */
+ writeb_relaxed(SPDSEL_SEL, miphy_phy->base + BOUNDARY1_REG);
+ writeb_relaxed(START_CLK_HF, miphy_phy->base + IDLL_TEST_REG);
+ val = rx_tx_spd[miphy_dev->sata_gen];
+ writeb_relaxed(val, miphy_phy->base + BOUNDARY3_REG);
+
+ /* Wait for HFC_READY = 0 */
+ ret = miphy365x_hfc_not_rdy(miphy_phy, miphy_dev);
+ if (ret)
+ return ret;
+
+ /* Compensation Recalibration */
+ miphy365x_set_comp(miphy_phy, miphy_dev);
+
+ switch (miphy_dev->sata_gen) {
+ case SATA_GEN3:
+ /*
+ * TX Swing target 550-600mv peak to peak diff
+ * Tx Slew target 90-110ps rising/falling time
+ * Rx Eq ON3, Sigdet threshold SDTH1
+ */
+ val = PD_VDDTFILTER | CONF_GEN_SEL_GEN3;
+ writeb_relaxed(val, miphy_phy->base + BUF_SEL_REG);
+ val = SWING_VAL | PREEMPH_VAL;
+ writeb_relaxed(val, miphy_phy->base + TXBUF1_REG);
+ writeb_relaxed(TXSLEW_VAL, miphy_phy->base + TXBUF2_REG);
+ writeb_relaxed(0x00, miphy_phy->base + RXBUF_OFFSET_CTRL_REG);
+ val = SDTHRES_VAL | EQ_ON3;
+ writeb_relaxed(val, miphy_phy->base + RXBUF_REG);
+ break;
+ case SATA_GEN2:
+ /*
+ * conf gen sel=0x1 to program Gen2 banked registers
+ * VDDT filter ON
+ * Tx Swing target 550-600mV peak-to-peak diff
+ * Tx Slew target 90-110 ps rising/falling time
+ * RX Equalization ON1, Sigdet threshold SDTH1
+ */
+ writeb_relaxed(CONF_GEN_SEL_GEN2,
+ miphy_phy->base + BUF_SEL_REG);
+ writeb_relaxed(SWING_VAL, miphy_phy->base + TXBUF1_REG);
+ writeb_relaxed(TXSLEW_VAL, miphy_phy->base + TXBUF2_REG);
+ val = SDTHRES_VAL | EQ_ON1;
+ writeb_relaxed(val, miphy_phy->base + RXBUF_REG);
+ break;
+ case SATA_GEN1:
+ /*
+ * conf gen sel = 00b to program Gen1 banked registers
+ * VDDT filter ON
+ * Tx Swing target 500-550mV peak-to-peak diff
+ * Tx Slew target120-140 ps rising/falling time
+ */
+ writeb_relaxed(PD_VDDTFILTER, miphy_phy->base + BUF_SEL_REG);
+ writeb_relaxed(SWING_VAL_GEN1, miphy_phy->base + TXBUF1_REG);
+ writeb_relaxed(TXSLEW_VAL_GEN1, miphy_phy->base + TXBUF2_REG);
+ break;
+ default:
+ break;
+ }
+
+ /* Force Macro1 in partial mode & release pll cal reset */
+ writeb_relaxed(RST_RX, miphy_phy->base + RESET_REG);
+ usleep_range(100, 150);
+
+ miphy365x_set_ssc(miphy_phy, miphy_dev);
+
+ /* Wait for phy_ready */
+ ret = miphy365x_rdy(miphy_phy, miphy_dev);
+ if (ret)
+ return ret;
+
+ /*
+ * Enable macro1 to use rx_lspd & tx_lspd
+ * Release Rx_Clock on first I-DLL phase on macro1
+ * Assert deserializer reset
+ * des_bit_lock_en is set
+ * bit lock detection strength
+ * Deassert deserializer reset
+ */
+ writeb_relaxed(0x00, miphy_phy->base + BOUNDARY1_REG);
+ writeb_relaxed(0x00, miphy_phy->base + IDLL_TEST_REG);
+ writeb_relaxed(RST_RX, miphy_phy->base + RESET_REG);
+ val = miphy_dev->sata_tx_pol_inv ?
+ (TX_POL | DES_BIT_LOCK_EN) : DES_BIT_LOCK_EN;
+ writeb_relaxed(val, miphy_phy->base + CTRL_REG);
+
+ val = BIT_LOCK_CNT_512 | BIT_LOCK_LEVEL;
+ writeb_relaxed(val, miphy_phy->base + DES_BITLOCK_REG);
+ writeb_relaxed(0x00, miphy_phy->base + RESET_REG);
+
+ return 0;
+}
+
+static int miphy365x_init(struct phy *phy)
+{
+ int ret = 0;
+ struct miphy365x *miphy_phy = phy_get_drvdata(phy);
+ struct miphy365x_dev *miphy_dev = miphy365x_phy_to_dev(miphy_phy);
+
+ mutex_lock(&miphy_dev->miphy_mutex);
+
+ ret = miphy365x_set_path(miphy_phy, miphy_dev);
+ if (ret) {
+ mutex_unlock(&miphy_dev->miphy_mutex);
+ return ret;
+ }
+
+ /* Initialise Miphy for PCIe or SATA */
+ if (miphy_phy->type == MIPHY_TYPE_PCIE)
+ miphy365x_init_pcie_port(miphy_phy, miphy_dev);
+ else
+ ret = miphy365x_init_sata_port(miphy_phy, miphy_dev);
+
+ mutex_unlock(&miphy_dev->miphy_mutex);
+
+ return ret;
+}
+
+static struct phy *miphy365x_xlate(struct device *dev,
+ struct of_phandle_args *args)
+{
+ struct miphy365x_dev *state = dev_get_drvdata(dev);
+ u8 port, type;
+
+ if (args->count != 2) {
+ dev_err(dev, "Invalid number of cells in 'phy' property\n");
+ return ERR_PTR(-EINVAL);
+ }
+
+ if (args->args[0] & 0xFFFFFF00 || args->args[1] & 0xFFFFFF00) {
+ dev_err(dev, "Unsupported flags set in 'phy' property\n");
+ return ERR_PTR(-EINVAL);
+ }
+
+ port = args->args[0];
+ type = args->args[1];
+
+ if (WARN_ON(port >= ARRAY_SIZE(ports)))
+ return ERR_PTR(-EINVAL);
+
+ if (type == MIPHY_TYPE_SATA)
+ state->phys[port].base = state->phys[port].sata;
+ else if (type == MIPHY_TYPE_PCIE)
+ state->phys[port].base = state->phys[port].pcie;
+ else {
+ WARN(1, "Invalid type specified in DT");
+ return ERR_PTR(-EINVAL);
+ }
+
+ state->phys[port].type = type;
+
+ return state->phys[port].phy;
+}
+
+static struct phy_ops miphy365x_ops = {
+ .init = miphy365x_init,
+ .owner = THIS_MODULE,
+};
+
+static int miphy365x_get_base_addr(struct platform_device *pdev,
+ struct miphy365x_phy *phy, u8 port)
+{
+ struct resource *res;
+ char type[6];
+
+ sprintf(type, "sata%d", port);
+
+ res = platform_get_resource_byname(pdev, IORESOURCE_MEM, type);
+ if (!res)
+ return -ENODEV;
+
+ phy->sata = devm_ioremap(&pdev->dev, res->start, resource_size(res));
+ if (!phy->sata)
+ return -ENOMEM;
+
+ sprintf(type, "pcie%d", port);
+
+ res = platform_get_resource_byname(pdev, IORESOURCE_MEM, type);
+ if (!res)
+ return -ENODEV;
+
+ phy->pcie = devm_ioremap(&pdev->dev, res->start, resource_size(res));
+ if (!phy->pcie)
+ return -ENOMEM;
+
+ return 0;
+}
+
+static int miphy365x_of_probe(struct device_node *np,
+ struct miphy365x_dev *phy_dev)
+{
+ phy_dev->regmap = syscon_regmap_lookup_by_phandle(np, "st,syscfg");
+ if (IS_ERR(phy_dev->regmap)) {
+ dev_err(phy_dev->dev, "No syscfg phandle specified\n");
+ return PTR_ERR(phy_dev->regmap);
+ }
+
+ of_property_read_u32(np, "st,sata-gen", &phy_dev->sata_gen);
+ if (!phy_dev->sata_gen)
+ phy_dev->sata_gen = SATA_GEN1;
+
+ phy_dev->pcie_tx_pol_inv =
+ of_property_read_bool(np, "st,pcie-tx-pol-inv");
+
+ phy_dev->sata_tx_pol_inv =
+ of_property_read_bool(np, "st,sata-tx-pol-inv");
+
+ return 0;
+}
+
+static int miphy365x_probe(struct platform_device *pdev)
+{
+ struct device_node *np = pdev->dev.of_node;
+ struct miphy365x_dev *phy_dev;
+ struct device *dev = &pdev->dev;
+ struct phy_provider *provider;
+ u8 port;
+ int ret;
+
+ if (!np) {
+ dev_err(dev, "No DT node found\n");
+ return -EINVAL;
+ }
+
+ phy_dev = devm_kzalloc(dev, sizeof(*phy_dev), GFP_KERNEL);
+ if (!phy_dev)
+ return -ENOMEM;
+
+ ret = miphy365x_of_probe(np, phy_dev);
+ if (ret)
+ return ret;
+
+ phy_dev->dev = dev;
+
+ dev_set_drvdata(dev, phy_dev);
+
+ mutex_init(&phy_dev->miphy_mutex);
+
+ for (port = 0; port < ARRAY_SIZE(ports); port++) {
+ struct phy *phy;
+
+ phy = devm_phy_create(dev, &miphy365x_ops, NULL);
+ if (IS_ERR(phy)) {
+ dev_err(dev, "failed to create PHY on port %d\n", port);
+ return PTR_ERR(phy);
+ }
+
+ phy_dev->phys[port].phy = phy;
+ phy_dev->phys[port].port = port;
+
+ ret = miphy365x_get_base_addr(pdev,
+ &phy_dev->phys[port], port);
+ if (ret)
+ return ret;
+
+ phy_set_drvdata(phy, &phy_dev->phys[port]);
+ }
+
+ provider = devm_of_phy_provider_register(dev, miphy365x_xlate);
+ if (IS_ERR(provider))
+ return PTR_ERR(provider);
+
+ return 0;
+}
+
+static const struct of_device_id miphy365x_of_match[] = {
+ { .compatible = "st,miphy365x-phy", },
+ { },
+};
+MODULE_DEVICE_TABLE(of, miphy365x_of_match);
+
+static struct platform_driver miphy365x_driver = {
+ .probe = miphy365x_probe,
+ .driver = {
+ .name = "miphy365x-phy",
+ .owner = THIS_MODULE,
+ .of_match_table = miphy365x_of_match,
+ }
+};
+module_platform_driver(miphy365x_driver);
+
+MODULE_AUTHOR("Alexandre Torgue <alexandre.torgue at st.com>");
+MODULE_DESCRIPTION("STMicroelectronics miphy365x driver");
+MODULE_LICENSE("GPL v2");
--
1.8.3.2
More information about the linux-arm-kernel
mailing list