[PATCH v2 05/12] usb: phy: add the Berlin USB PHY driver
Felipe Balbi
balbi at ti.com
Fri Jun 27 08:56:22 PDT 2014
On Tue, Jun 24, 2014 at 12:35:14PM +0200, Antoine Ténart wrote:
> Add the driver driving the Marvell Berlin USB PHY. This allows to
> initialize the PHY and to use it from the USB driver later.
>
> Signed-off-by: Antoine Ténart <antoine.tenart at free-electrons.com>
since this is a brand new driver, it should go to drivers/phy instead.
> ---
> drivers/usb/phy/Kconfig | 9 ++
> drivers/usb/phy/Makefile | 1 +
> drivers/usb/phy/phy-berlin-usb.c | 211 +++++++++++++++++++++++++++++++++++++++
> 3 files changed, 221 insertions(+)
> create mode 100644 drivers/usb/phy/phy-berlin-usb.c
>
> diff --git a/drivers/usb/phy/Kconfig b/drivers/usb/phy/Kconfig
> index e253fa05be68..9a47cc1c73fe 100644
> --- a/drivers/usb/phy/Kconfig
> +++ b/drivers/usb/phy/Kconfig
> @@ -18,6 +18,15 @@ config AB8500_USB
> This transceiver supports high and full speed devices plus,
> in host mode, low speed.
>
> +config BERLIN_USBPHY
> + tristate "Marvell Berlin USB Transceiver Driver"
> + depends on ARCH_BERLIN
> + select USB_PHY
> + help
> + Enable this to support the USB tranceiver on Marvell Berlin
> + SoCs.
> +
> +
> config FSL_USB2_OTG
> bool "Freescale USB OTG Transceiver Driver"
> depends on USB_EHCI_FSL && USB_FSL_USB2 && USB_OTG_FSM && PM_RUNTIME
> diff --git a/drivers/usb/phy/Makefile b/drivers/usb/phy/Makefile
> index 24a91332d4ad..450ac91c5e20 100644
> --- a/drivers/usb/phy/Makefile
> +++ b/drivers/usb/phy/Makefile
> @@ -7,6 +7,7 @@ obj-$(CONFIG_OF) += of.o
> # transceiver drivers, keep the list sorted
>
> obj-$(CONFIG_AB8500_USB) += phy-ab8500-usb.o
> +obj-$(CONFIG_BERLIN_USBPHY) += phy-berlin-usb.o
> obj-$(CONFIG_FSL_USB2_OTG) += phy-fsl-usb.o
> obj-$(CONFIG_ISP1301_OMAP) += phy-isp1301-omap.o
> obj-$(CONFIG_NOP_USB_XCEIV) += phy-generic.o
> diff --git a/drivers/usb/phy/phy-berlin-usb.c b/drivers/usb/phy/phy-berlin-usb.c
> new file mode 100644
> index 000000000000..276d28f5cb83
> --- /dev/null
> +++ b/drivers/usb/phy/phy-berlin-usb.c
> @@ -0,0 +1,211 @@
> +/*
> + * Copyright (C) 2014 Marvell Technology Group Ltd.
> + *
> + * Antoine Ténart <antoine.tenart at free-electrons.com>
> + * Jisheng Zhang <jszhang at marvell.com>
> + *
> + * This file is licensed under the terms of the GNU General Public
> + * License version 2. This program is licensed "as is" without any
> + * warranty of any kind, whether express or implied.
> + */
> +
> +#include <linux/gpio.h>
> +#include <linux/io.h>
> +#include <linux/module.h>
> +#include <linux/of_device.h>
> +#include <linux/of_gpio.h>
> +#include <linux/platform_device.h>
> +#include <linux/reset.h>
> +#include <linux/usb/phy.h>
> +
> +#define USB_PHY_PLL 0x04
> +#define USB_PHY_PLL_CONTROL 0x08
> +#define USB_PHY_TX_CTRL0 0x10
> +#define USB_PHY_TX_CTRL1 0x14
> +#define USB_PHY_TX_CTRL2 0x18
> +#define USB_PHY_RX_CTRL 0x20
> +#define USB_PHY_ANALOG 0x34
> +
> +/* USB_PHY_PLL */
> +#define CLK_REF_DIV(x) ((x) << 4)
> +#define FEEDBACK_CLK_DIV(x) ((x) << 8)
> +
> +/* USB_PHY_PLL_CONTROL */
> +#define CLK_STABLE BIT(0)
> +#define PLL_CTRL_PIN BIT(1)
> +#define PLL_CTRL_REG BIT(2)
> +#define PLL_ON BIT(3)
> +#define PHASE_OFF_TOL_125 (0x0 << 5)
> +#define PHASE_OFF_TOL_250 BIT(5)
> +#define KVC0_CALIB (0x0 << 9)
> +#define KVC0_REG_CTRL BIT(9)
> +#define KVC0_HIGH (0x0 << 10)
> +#define KVC0_LOW (0x3 << 10)
> +#define CLK_BLK_EN BIT(13)
> +
> +/* USB_PHY_TX_CTRL0 */
> +#define EXT_HS_RCAL_EN BIT(3)
> +#define EXT_FS_RCAL_EN BIT(4)
> +#define IMPCAL_VTH_DIV(x) ((x) << 5)
> +#define EXT_RS_RCAL_DIV(x) ((x) << 8)
> +#define EXT_FS_RCAL_DIV(x) ((x) << 12)
> +
> +/* USB_PHY_TX_CTRL1 */
> +#define TX_VDD15_14 (0x0 << 4)
> +#define TX_VDD15_15 BIT(4)
> +#define TX_VDD15_16 (0x2 << 4)
> +#define TX_VDD15_17 (0x3 << 4)
> +#define TX_VDD12_VDD (0x0 << 6)
> +#define TX_VDD12_11 BIT(6)
> +#define TX_VDD12_12 (0x2 << 6)
> +#define TX_VDD12_13 (0x3 << 6)
> +#define LOW_VDD_EN BIT(8)
> +#define TX_OUT_AMP(x) ((x) << 9)
> +
> +/* USB_PHY_TX_CTRL2 */
> +#define TX_CHAN_CTRL_REG(x) ((x) << 0)
> +#define DRV_SLEWRATE(x) ((x) << 4)
> +#define IMP_CAL_FS_HS_DLY_0 (0x0 << 6)
> +#define IMP_CAL_FS_HS_DLY_1 BIT(6)
> +#define IMP_CAL_FS_HS_DLY_2 (0x2 << 6)
> +#define IMP_CAL_FS_HS_DLY_3 (0x3 << 6)
> +#define FS_DRV_EN_MASK(x) ((x) << 8)
> +#define HS_DRV_EN_MASK(x) ((x) << 12)
> +
> +/* USB_PHY_RX_CTRL */
> +#define PHASE_FREEZE_DLY_2_CL (0x0 << 0)
> +#define PHASE_FREEZE_DLY_4_CL BIT(0)
> +#define ACK_LENGTH_8_CL (0x0 << 2)
> +#define ACK_LENGTH_12_CL BIT(2)
> +#define ACK_LENGTH_16_CL (0x2 << 2)
> +#define ACK_LENGTH_20_CL (0x3 << 2)
> +#define SQ_LENGTH_3 (0x0 << 4)
> +#define SQ_LENGTH_6 BIT(4)
> +#define SQ_LENGTH_9 (0x2 << 4)
> +#define SQ_LENGTH_12 (0x3 << 4)
> +#define DISCON_THRESHOLD_260 (0x0 << 6)
> +#define DISCON_THRESHOLD_270 BIT(6)
> +#define DISCON_THRESHOLD_280 (0x2 << 6)
> +#define DISCON_THRESHOLD_290 (0x3 << 6)
> +#define SQ_THRESHOLD(x) ((x) << 8)
> +#define LPF_COEF(x) ((x) << 12)
> +#define INTPL_CUR_10 (0x0 << 14)
> +#define INTPL_CUR_20 BIT(14)
> +#define INTPL_CUR_30 (0x2 << 14)
> +#define INTPL_CUR_40 (0x3 << 14)
> +
> +/* USB_PHY_ANALOG */
> +#define ANA_PWR_UP BIT(1)
> +#define ANA_PWR_DOWN BIT(2)
> +#define V2I_VCO_RATIO(x) ((x) << 7)
> +#define R_ROTATE_90 (0x0 << 10)
> +#define R_ROTATE_0 BIT(10)
> +#define MODE_TEST_EN BIT(11)
> +#define ANA_TEST_DC_CTRL(x) ((x) << 12)
> +
> +#define to_berlin_phy_priv(p) container_of((p), struct berlin_phy_priv, phy)
> +
> +static const u32 phy_berlin_pll_dividers[] = {
> + /* Berlin 2 */
> + CLK_REF_DIV(0xc) | FEEDBACK_CLK_DIV(0x54),
> + /* Berlin 2CD */
> + CLK_REF_DIV(0x6) | FEEDBACK_CLK_DIV(0x55),
> +};
> +
> +struct berlin_phy_priv {
> + void __iomem *base;
> + struct usb_phy phy;
> + struct reset_control *rst_ctrl;
> + u32 pll_divider;
> +};
> +
> +static int berlin_phy_init(struct usb_phy *phy)
> +{
> + struct berlin_phy_priv *priv = to_berlin_phy_priv(phy);
> +
> + reset_control_reset(priv->rst_ctrl);
> +
> + writel(priv->pll_divider,
> + priv->base + USB_PHY_PLL);
> + writel(CLK_STABLE | PLL_CTRL_REG | PHASE_OFF_TOL_250 | KVC0_REG_CTRL |
> + CLK_BLK_EN, priv->base + USB_PHY_PLL_CONTROL);
> + writel(V2I_VCO_RATIO(0x5) | R_ROTATE_0 | ANA_TEST_DC_CTRL(0x5),
> + priv->base + USB_PHY_ANALOG);
> + writel(PHASE_FREEZE_DLY_4_CL | ACK_LENGTH_16_CL | SQ_LENGTH_12 |
> + DISCON_THRESHOLD_260 | SQ_THRESHOLD(0xa) | LPF_COEF(0x2) |
> + INTPL_CUR_30, priv->base + USB_PHY_RX_CTRL);
> +
> + writel(TX_VDD12_13 | TX_OUT_AMP(0x3), priv->base + USB_PHY_TX_CTRL1);
> + writel(EXT_HS_RCAL_EN | IMPCAL_VTH_DIV(0x3) | EXT_RS_RCAL_DIV(0x4),
> + priv->base + USB_PHY_TX_CTRL0);
> +
> + writel(EXT_HS_RCAL_EN | IMPCAL_VTH_DIV(0x3) | EXT_RS_RCAL_DIV(0x4) |
> + EXT_FS_RCAL_DIV(0x2), priv->base + USB_PHY_TX_CTRL0);
> +
> + writel(EXT_HS_RCAL_EN | IMPCAL_VTH_DIV(0x3) | EXT_RS_RCAL_DIV(0x4),
> + priv->base + USB_PHY_TX_CTRL0);
> + writel(TX_CHAN_CTRL_REG(0xf) | DRV_SLEWRATE(0x3) | IMP_CAL_FS_HS_DLY_3 |
> + FS_DRV_EN_MASK(0xd), priv->base + USB_PHY_TX_CTRL2);
> +
> + return 0;
> +}
> +
> +static const struct of_device_id phy_berlin_sata_of_match[] = {
> + {
> + .compatible = "marvell,berlin2-usb-phy",
> + .data = &phy_berlin_pll_dividers[0],
> + },
> + {
> + .compatible = "marvell,berlin2cd-usb-phy",
> + .data = &phy_berlin_pll_dividers[1],
> + },
> + { },
> +};
> +MODULE_DEVICE_TABLE(of, phy_berlin_sata_of_match);
> +
> +static int berlin_phy_probe(struct platform_device *pdev)
> +{
> + const struct of_device_id *match =
> + of_match_device(phy_berlin_sata_of_match, &pdev->dev);
> + struct berlin_phy_priv *priv;
> + struct resource *res;
> +
> + priv = devm_kzalloc(&pdev->dev, sizeof(*priv), GFP_KERNEL);
> + if (!priv)
> + return -ENOMEM;
> +
> + res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> + priv->base = devm_ioremap_resource(&pdev->dev, res);
> + if (IS_ERR(priv->base))
> + return PTR_ERR(priv->base);
> +
> + priv->rst_ctrl = devm_reset_control_get(&pdev->dev, NULL);
> + if (IS_ERR(priv->rst_ctrl))
> + return PTR_ERR(priv->rst_ctrl);
> +
> + priv->pll_divider = *((u32 *)match->data);
> +
> + priv->phy.io_priv = priv->base;
> + priv->phy.dev = &pdev->dev;
> + priv->phy.label = "phy-berlin-usb";
> + priv->phy.init = berlin_phy_init;
> + priv->phy.type = USB_PHY_TYPE_USB2;
> +
> + platform_set_drvdata(pdev, priv);
> +
> + return usb_add_phy_dev(&priv->phy);
> +}
> +
> +static struct platform_driver phy_berlin_usb_driver = {
> + .probe = berlin_phy_probe,
> + .driver = {
> + .name = "phy-berlin-usb",
> + .owner = THIS_MODULE,
> + .of_match_table = phy_berlin_sata_of_match,
> + },
> +};
> +module_platform_driver(phy_berlin_usb_driver);
> +
> +MODULE_AUTHOR("Antoine Ténart <antoine.tenart at free-electrons.com>");
> +MODULE_DESCRIPTION("Marvell Berlin USB PHY driver");
> +MODULE_LICENSE("GPL");
> --
> 1.9.1
>
--
balbi
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 819 bytes
Desc: Digital signature
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20140627/845cf3a3/attachment-0001.sig>
More information about the linux-arm-kernel
mailing list