mainline boot: 64 boots: 62 pass, 2 fail (v3.16-rc1-2-gebe0618)

[Laura Abbott]

On 6/25/2014 5:13 AM, Tushar Behera wrote:
> On 06/25/2014 03:59 AM, Laura Abbott wrote:
>> On 6/24/2014 10:47 AM, Laura Abbott wrote:
>>> On 6/23/2014 11:32 AM, Kevin Hilman wrote:
>>>> On Sun, Jun 22, 2014 at 8:56 PM, Tushar Behera <trblinux at gmail.com> wrote:
>>>>> Adding linux-samsung-soc and linux-arm-kernel ML for wider audience.
>>>>>
>>>>> On 06/19/2014 04:12 PM, Tushar Behera wrote:
>>>>>> On 06/19/2014 03:02 PM, Tushar Behera wrote:
>>>>>>> On 06/18/2014 09:22 AM, Kevin Hilman wrote:
>>>>>>>> On Tue, Jun 17, 2014 at 8:26 PM, Tushar Behera <trblinux at gmail.com> wrote:
>>>>>>>>> On 06/17/2014 10:23 PM, Kevin Hilman wrote:
>>>>>>>>>> Sachin,
>>>>>>>>>>
>>>>>>>>>> On Mon, Jun 16, 2014 at 11:16 PM, Kevin's boot bot <khilman at linaro.org> wrote:
>>>>>>>>>>>
>>>>>>>>>>> Tree/Branch: mainline
>>>>>>>>>>> Git describe: v3.16-rc1-2-gebe0618
>>>>>>>>>>> Failed boot tests (console logs at the end)
>>>>>>>>>>> ===========================================
>>>>>>>>>>>      exynos5420-arndale-octa:     FAIL:    arm-exynos_defconfig
>>>>>>>>>>>                 ste-snowball:     FAIL:    arm-u8500_defconfig
>>>>>>>>>>
>>>>>>>>>> FYI... these failures are getting more consistent on my octa board,
>>>>>>>>>> but still not failing every time.
>>>>>>>>>>
>>>>>>>>>> Kevin
>>>>>>>>>>
>>>>>>>>>
>>>>>>>>> Hi Kevin,
>>>>>>>>>
>>>>>>>>> Same here.
>>>>>>>>>
>>>>>>>>> Observation: If you soft-reset the board (through the jumpers) after
>>>>>>>>> getting this problem, the problem keeps repeating. But if you hard-reset
>>>>>>>>> the board (by removing the power cord), the problem doesn't occur during
>>>>>>>>> next iteration.
>>>>>>>>
>>>>>>>> I don't ever use the soft-reset, I only toggle the wall power.  I
>>>>>>>> don't ever actually remove the power cord though, I'm using a
>>>>>>>> USB-controlled relay to toggle the wall power.
>>>>>>>>
>>>>>>>> Kevin
>>>>>>>>
>>>>>>>
>>>>>>> Laura,
>>>>>>>
>>>>>>> We are getting following kernel panic [1] (not always, but quite
>>>>>>> regularly) while booting Arndale-Octa (based on Samsung's Exynos5420)
>>>>>>> board with upstream kernel. I haven't observed this issue with other
>>>>>>> boards yet.
>>>>>>>
>>>>>>> This issue is observed when I am booting with uImage + dtb (within
>>>>>>> roughly ~10 iterations).
>>>>>>>
>>>>>>
>>>>>> Some more information:
>>>>>>
>>>>>> The boot logs are provided in pastebin, okay[2] and failed[3].
>>>>>>
>>>>>> In case of boot failures, I am getting a higher value for vm_total_pages
>>>>>> (684424 in [3]). In case of successful boot on my board, it is always
>>>>>> 521232 [2] on my board.
>>>>
>>>> I can confirm that reverting the "Get rid of meminfo" patch gets the
>>>> Octa board booting reliably again for me also.
>>>>
>>>> In case it helps, some boot logs for failures from the last copule
>>>> linux-next build/boot cycles can be seen here:
>>>> http://armcloud.us/kernel-ci/next/next-20140623/arm-exynos_defconfig/boot-exynos5420-arndale-octa.log
>>>> http://armcloud.us/kernel-ci/next/next-20140620/arm-exynos_defconfig/boot-exynos5420-arndale-octa.log
>>>>
>>>
>>> Sorry, I missed this yesterday. I'm going to take a look.
>>>
>>
>> Were all of 
>>
>> http://pastebin.com/1iLaizuL
>> http://pastebin.com/5tdDt4GL
>> http://armcloud.us/kernel-ci/next/next-20140623/arm-exynos_defconfig/boot-exynos5420-arndale-octa.log
>> http://armcloud.us/kernel-ci/next/next-20140620/arm-exynos_defconfig/boot-exynos5420-arndale-octa.log
>>
>> collected on the same type of board with the same amount of DRAM? I'm seeing a
>> different amount of total pages across all those logs. All the logs have the
>> same lowmem limit so it seems like the upper bound was being calculated
>> incorrectly for passing to free_area_init_node. Nothing is immediately jumping
>> out at me so can you boot up with a small debug patch?
>>
>> diff --git a/arch/arm/mm/init.c b/arch/arm/mm/init.c
>> index 659c75d..88eac1f 100644
>> --- a/arch/arm/mm/init.c
>> +++ b/arch/arm/mm/init.c
>> @@ -187,6 +187,8 @@ static void __init zone_sizes_init(unsigned long min, unsigned long max_low,
>>         unsigned long zone_size[MAX_NR_ZONES], zhole_size[MAX_NR_ZONES];
>>         struct memblock_region *reg;
>>  
>> +       pr_err("XXXXXXX min %lx max_low %lx max_high %lx\n", min, max_low, max_high);
>> +       __memblock_dump_all();
>>         /*
>>          * initialise the zones.
>>          */
>>
>> It would be helpful to do this across a few bootups to see if the values are
>> actually consistent. I'll keep looking in the meantime.
>>
>> Thanks,
>> Laura
>>
> 
> Thanks Laura for the pointer. In case of error, I am getting some random
> memblock_add() calls from drivers/of/fdt.c:early_init_dt_scan_memory.
> 
> The issue seems to be from u-boot, where it is not updating the memory
> subnode properly. I have got a fix for the u-boot, which I am testing
> right now. I will update tomorrow after I do some more test.
> 

I'm concerned my change can stay as is if this is exposing an issue
in u-boot. Asking people to change bootloaders rarely ends well. Can
you elaborate on what u-boot is doing that would be exposing this
issue?

Thanks,
Laura


-- 
Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum,
hosted by The Linux Foundation