[PATCH] ARM: STi: DT: STiH41x: Convert all uppercase non-defines to lowercase
Lee Jones
lee.jones at linaro.org
Wed Jun 25 07:53:54 PDT 2014
> Suggested-by: Olof Johansson <olof at lixom.net>
> Signed-off-by: Lee Jones <lee.jones at linaro.org>
> ---
> arch/arm/boot/dts/stih415-pinctrl.dtsi | 340 +++++++++++++++---------------
> arch/arm/boot/dts/stih416-b2020-revE.dts | 6 +-
> arch/arm/boot/dts/stih416-pinctrl.dtsi | 342 +++++++++++++++----------------
> arch/arm/boot/dts/stih41x-b2000.dtsi | 6 +-
> arch/arm/boot/dts/stih41x-b2020.dtsi | 6 +-
> 5 files changed, 350 insertions(+), 350 deletions(-)
What happened to this Maxime?
It was Acked by Olof, then died. Did it slip through the net?
> diff --git a/arch/arm/boot/dts/stih415-pinctrl.dtsi b/arch/arm/boot/dts/stih415-pinctrl.dtsi
> index caeac7e..1e0255d 100644
> --- a/arch/arm/boot/dts/stih415-pinctrl.dtsi
> +++ b/arch/arm/boot/dts/stih415-pinctrl.dtsi
> @@ -11,33 +11,33 @@
> / {
>
> aliases {
> - gpio0 = &PIO0;
> - gpio1 = &PIO1;
> - gpio2 = &PIO2;
> - gpio3 = &PIO3;
> - gpio4 = &PIO4;
> - gpio5 = &PIO5;
> - gpio6 = &PIO6;
> - gpio7 = &PIO7;
> - gpio8 = &PIO8;
> - gpio9 = &PIO9;
> - gpio10 = &PIO10;
> - gpio11 = &PIO11;
> - gpio12 = &PIO12;
> - gpio13 = &PIO13;
> - gpio14 = &PIO14;
> - gpio15 = &PIO15;
> - gpio16 = &PIO16;
> - gpio17 = &PIO17;
> - gpio18 = &PIO18;
> - gpio19 = &PIO100;
> - gpio20 = &PIO101;
> - gpio21 = &PIO102;
> - gpio22 = &PIO103;
> - gpio23 = &PIO104;
> - gpio24 = &PIO105;
> - gpio25 = &PIO106;
> - gpio26 = &PIO107;
> + gpio0 = &pio0;
> + gpio1 = &pio1;
> + gpio2 = &pio2;
> + gpio3 = &pio3;
> + gpio4 = &pio4;
> + gpio5 = &pio5;
> + gpio6 = &pio6;
> + gpio7 = &pio7;
> + gpio8 = &pio8;
> + gpio9 = &pio9;
> + gpio10 = &pio10;
> + gpio11 = &pio11;
> + gpio12 = &pio12;
> + gpio13 = &pio13;
> + gpio14 = &pio14;
> + gpio15 = &pio15;
> + gpio16 = &pio16;
> + gpio17 = &pio17;
> + gpio18 = &pio18;
> + gpio19 = &pio100;
> + gpio20 = &pio101;
> + gpio21 = &pio102;
> + gpio22 = &pio103;
> + gpio23 = &pio104;
> + gpio24 = &pio105;
> + gpio25 = &pio106;
> + gpio26 = &pio107;
> };
>
> soc {
> @@ -52,7 +52,7 @@
> interrupts-names = "irqmux";
> ranges = <0 0xfe610000 0x5000>;
>
> - PIO0: gpio at fe610000 {
> + pio0: gpio at fe610000 {
> gpio-controller;
> #gpio-cells = <1>;
> interrupt-controller;
> @@ -60,7 +60,7 @@
> reg = <0 0x100>;
> st,bank-name = "PIO0";
> };
> - PIO1: gpio at fe611000 {
> + pio1: gpio at fe611000 {
> gpio-controller;
> #gpio-cells = <1>;
> interrupt-controller;
> @@ -68,7 +68,7 @@
> reg = <0x1000 0x100>;
> st,bank-name = "PIO1";
> };
> - PIO2: gpio at fe612000 {
> + pio2: gpio at fe612000 {
> gpio-controller;
> #gpio-cells = <1>;
> interrupt-controller;
> @@ -76,7 +76,7 @@
> reg = <0x2000 0x100>;
> st,bank-name = "PIO2";
> };
> - PIO3: gpio at fe613000 {
> + pio3: gpio at fe613000 {
> gpio-controller;
> #gpio-cells = <1>;
> interrupt-controller;
> @@ -84,7 +84,7 @@
> reg = <0x3000 0x100>;
> st,bank-name = "PIO3";
> };
> - PIO4: gpio at fe614000 {
> + pio4: gpio at fe614000 {
> gpio-controller;
> #gpio-cells = <1>;
> interrupt-controller;
> @@ -96,8 +96,8 @@
> sbc_serial1 {
> pinctrl_sbc_serial1:sbc_serial1 {
> st,pins {
> - tx = <&PIO2 6 ALT3 OUT>;
> - rx = <&PIO2 7 ALT3 IN>;
> + tx = <&pio2 6 ALT3 OUT>;
> + rx = <&pio2 7 ALT3 IN>;
> };
> };
> };
> @@ -105,15 +105,15 @@
> keyscan {
> pinctrl_keyscan: keyscan {
> st,pins {
> - keyin0 = <&PIO0 2 ALT2 IN>;
> - keyin1 = <&PIO0 3 ALT2 IN>;
> - keyin2 = <&PIO0 4 ALT2 IN>;
> - keyin3 = <&PIO2 6 ALT2 IN>;
> -
> - keyout0 = <&PIO1 6 ALT2 OUT>;
> - keyout1 = <&PIO1 7 ALT2 OUT>;
> - keyout2 = <&PIO0 6 ALT2 OUT>;
> - keyout3 = <&PIO2 7 ALT2 OUT>;
> + keyin0 = <&pio0 2 ALT2 IN>;
> + keyin1 = <&pio0 3 ALT2 IN>;
> + keyin2 = <&pio0 4 ALT2 IN>;
> + keyin3 = <&pio2 6 ALT2 IN>;
> +
> + keyout0 = <&pio1 6 ALT2 OUT>;
> + keyout1 = <&pio1 7 ALT2 OUT>;
> + keyout2 = <&pio0 6 ALT2 OUT>;
> + keyout3 = <&pio2 7 ALT2 OUT>;
> };
> };
> };
> @@ -121,8 +121,8 @@
> sbc_i2c0 {
> pinctrl_sbc_i2c0_default: sbc_i2c0-default {
> st,pins {
> - sda = <&PIO4 6 ALT1 BIDIR>;
> - scl = <&PIO4 5 ALT1 BIDIR>;
> + sda = <&pio4 6 ALT1 BIDIR>;
> + scl = <&pio4 5 ALT1 BIDIR>;
> };
> };
> };
> @@ -130,8 +130,8 @@
> sbc_i2c1 {
> pinctrl_sbc_i2c1_default: sbc_i2c1-default {
> st,pins {
> - sda = <&PIO3 2 ALT2 BIDIR>;
> - scl = <&PIO3 1 ALT2 BIDIR>;
> + sda = <&pio3 2 ALT2 BIDIR>;
> + scl = <&pio3 1 ALT2 BIDIR>;
> };
> };
> };
> @@ -139,7 +139,7 @@
> rc{
> pinctrl_ir: ir0 {
> st,pins {
> - ir = <&PIO4 0 ALT2 IN>;
> + ir = <&pio4 0 ALT2 IN>;
> };
> };
> };
> @@ -147,49 +147,49 @@
> gmac1 {
> pinctrl_mii1: mii1 {
> st,pins {
> - txd0 = <&PIO0 0 ALT1 OUT SE_NICLK_IO 0 CLK_A>;
> - txd1 = <&PIO0 1 ALT1 OUT SE_NICLK_IO 0 CLK_A>;
> - txd2 = <&PIO0 2 ALT1 OUT SE_NICLK_IO 0 CLK_A>;
> - txd3 = <&PIO0 3 ALT1 OUT SE_NICLK_IO 0 CLK_A>;
> - txer = <&PIO0 4 ALT1 OUT SE_NICLK_IO 0 CLK_A>;
> - txen = <&PIO0 5 ALT1 OUT SE_NICLK_IO 0 CLK_A>;
> - txclk = <&PIO0 6 ALT1 IN NICLK 0 CLK_A>;
> - col = <&PIO0 7 ALT1 IN BYPASS 1000>;
> - mdio = <&PIO1 0 ALT1 OUT BYPASS 0>;
> - mdc = <&PIO1 1 ALT1 OUT NICLK 0 CLK_A>;
> - crs = <&PIO1 2 ALT1 IN BYPASS 1000>;
> - mdint = <&PIO1 3 ALT1 IN BYPASS 0>;
> - rxd0 = <&PIO1 4 ALT1 IN SE_NICLK_IO 0 CLK_A>;
> - rxd1 = <&PIO1 5 ALT1 IN SE_NICLK_IO 0 CLK_A>;
> - rxd2 = <&PIO1 6 ALT1 IN SE_NICLK_IO 0 CLK_A>;
> - rxd3 = <&PIO1 7 ALT1 IN SE_NICLK_IO 0 CLK_A>;
> - rxdv = <&PIO2 0 ALT1 IN SE_NICLK_IO 0 CLK_A>;
> - rx_er = <&PIO2 1 ALT1 IN SE_NICLK_IO 0 CLK_A>;
> - rxclk = <&PIO2 2 ALT1 IN NICLK 0 CLK_A>;
> - phyclk = <&PIO2 3 ALT1 IN NICLK 1000 CLK_A>;
> + txd0 = <&pio0 0 ALT1 OUT SE_NICLK_IO 0 CLK_A>;
> + txd1 = <&pio0 1 ALT1 OUT SE_NICLK_IO 0 CLK_A>;
> + txd2 = <&pio0 2 ALT1 OUT SE_NICLK_IO 0 CLK_A>;
> + txd3 = <&pio0 3 ALT1 OUT SE_NICLK_IO 0 CLK_A>;
> + txer = <&pio0 4 ALT1 OUT SE_NICLK_IO 0 CLK_A>;
> + txen = <&pio0 5 ALT1 OUT SE_NICLK_IO 0 CLK_A>;
> + txclk = <&pio0 6 ALT1 IN NICLK 0 CLK_A>;
> + col = <&pio0 7 ALT1 IN BYPASS 1000>;
> + mdio = <&pio1 0 ALT1 OUT BYPASS 0>;
> + mdc = <&pio1 1 ALT1 OUT NICLK 0 CLK_A>;
> + crs = <&pio1 2 ALT1 IN BYPASS 1000>;
> + mdint = <&pio1 3 ALT1 IN BYPASS 0>;
> + rxd0 = <&pio1 4 ALT1 IN SE_NICLK_IO 0 CLK_A>;
> + rxd1 = <&pio1 5 ALT1 IN SE_NICLK_IO 0 CLK_A>;
> + rxd2 = <&pio1 6 ALT1 IN SE_NICLK_IO 0 CLK_A>;
> + rxd3 = <&pio1 7 ALT1 IN SE_NICLK_IO 0 CLK_A>;
> + rxdv = <&pio2 0 ALT1 IN SE_NICLK_IO 0 CLK_A>;
> + rx_er = <&pio2 1 ALT1 IN SE_NICLK_IO 0 CLK_A>;
> + rxclk = <&pio2 2 ALT1 IN NICLK 0 CLK_A>;
> + phyclk = <&pio2 3 ALT1 IN NICLK 1000 CLK_A>;
> };
> };
>
> pinctrl_rgmii1: rgmii1-0 {
> st,pins {
> - txd0 = <&PIO0 0 ALT1 OUT DE_IO 1000 CLK_A>;
> - txd1 = <&PIO0 1 ALT1 OUT DE_IO 1000 CLK_A>;
> - txd2 = <&PIO0 2 ALT1 OUT DE_IO 1000 CLK_A>;
> - txd3 = <&PIO0 3 ALT1 OUT DE_IO 1000 CLK_A>;
> - txen = <&PIO0 5 ALT1 OUT DE_IO 0 CLK_A>;
> - txclk = <&PIO0 6 ALT1 IN NICLK 0 CLK_A>;
> - mdio = <&PIO1 0 ALT1 OUT BYPASS 0>;
> - mdc = <&PIO1 1 ALT1 OUT NICLK 0 CLK_A>;
> - rxd0 = <&PIO1 4 ALT1 IN DE_IO 0 CLK_A>;
> - rxd1 = <&PIO1 5 ALT1 IN DE_IO 0 CLK_A>;
> - rxd2 = <&PIO1 6 ALT1 IN DE_IO 0 CLK_A>;
> - rxd3 = <&PIO1 7 ALT1 IN DE_IO 0 CLK_A>;
> -
> - rxdv = <&PIO2 0 ALT1 IN DE_IO 500 CLK_A>;
> - rxclk = <&PIO2 2 ALT1 IN NICLK 0 CLK_A>;
> - phyclk = <&PIO2 3 ALT4 OUT NICLK 0 CLK_B>;
> -
> - clk125= <&PIO3 7 ALT4 IN NICLK 0 CLK_A>;
> + txd0 = <&pio0 0 ALT1 OUT DE_IO 1000 CLK_A>;
> + txd1 = <&pio0 1 ALT1 OUT DE_IO 1000 CLK_A>;
> + txd2 = <&pio0 2 ALT1 OUT DE_IO 1000 CLK_A>;
> + txd3 = <&pio0 3 ALT1 OUT DE_IO 1000 CLK_A>;
> + txen = <&pio0 5 ALT1 OUT DE_IO 0 CLK_A>;
> + txclk = <&pio0 6 ALT1 IN NICLK 0 CLK_A>;
> + mdio = <&pio1 0 ALT1 OUT BYPASS 0>;
> + mdc = <&pio1 1 ALT1 OUT NICLK 0 CLK_A>;
> + rxd0 = <&pio1 4 ALT1 IN DE_IO 0 CLK_A>;
> + rxd1 = <&pio1 5 ALT1 IN DE_IO 0 CLK_A>;
> + rxd2 = <&pio1 6 ALT1 IN DE_IO 0 CLK_A>;
> + rxd3 = <&pio1 7 ALT1 IN DE_IO 0 CLK_A>;
> +
> + rxdv = <&pio2 0 ALT1 IN DE_IO 500 CLK_A>;
> + rxclk = <&pio2 2 ALT1 IN NICLK 0 CLK_A>;
> + phyclk = <&pio2 3 ALT4 OUT NICLK 0 CLK_B>;
> +
> + clk125= <&pio3 7 ALT4 IN NICLK 0 CLK_A>;
> };
> };
> };
> @@ -206,7 +206,7 @@
> interrupts-names = "irqmux";
> ranges = <0 0xfee00000 0x8000>;
>
> - PIO5: gpio at fee00000 {
> + pio5: gpio at fee00000 {
> gpio-controller;
> #gpio-cells = <1>;
> interrupt-controller;
> @@ -214,7 +214,7 @@
> reg = <0 0x100>;
> st,bank-name = "PIO5";
> };
> - PIO6: gpio at fee01000 {
> + pio6: gpio at fee01000 {
> gpio-controller;
> #gpio-cells = <1>;
> interrupt-controller;
> @@ -222,7 +222,7 @@
> reg = <0x1000 0x100>;
> st,bank-name = "PIO6";
> };
> - PIO7: gpio at fee02000 {
> + pio7: gpio at fee02000 {
> gpio-controller;
> #gpio-cells = <1>;
> interrupt-controller;
> @@ -230,7 +230,7 @@
> reg = <0x2000 0x100>;
> st,bank-name = "PIO7";
> };
> - PIO8: gpio at fee03000 {
> + pio8: gpio at fee03000 {
> gpio-controller;
> #gpio-cells = <1>;
> interrupt-controller;
> @@ -238,7 +238,7 @@
> reg = <0x3000 0x100>;
> st,bank-name = "PIO8";
> };
> - PIO9: gpio at fee04000 {
> + pio9: gpio at fee04000 {
> gpio-controller;
> #gpio-cells = <1>;
> interrupt-controller;
> @@ -246,7 +246,7 @@
> reg = <0x4000 0x100>;
> st,bank-name = "PIO9";
> };
> - PIO10: gpio at fee05000 {
> + pio10: gpio at fee05000 {
> gpio-controller;
> #gpio-cells = <1>;
> interrupt-controller;
> @@ -254,7 +254,7 @@
> reg = <0x5000 0x100>;
> st,bank-name = "PIO10";
> };
> - PIO11: gpio at fee06000 {
> + pio11: gpio at fee06000 {
> gpio-controller;
> #gpio-cells = <1>;
> interrupt-controller;
> @@ -262,7 +262,7 @@
> reg = <0x6000 0x100>;
> st,bank-name = "PIO11";
> };
> - PIO12: gpio at fee07000 {
> + pio12: gpio at fee07000 {
> gpio-controller;
> #gpio-cells = <1>;
> interrupt-controller;
> @@ -274,8 +274,8 @@
> i2c0 {
> pinctrl_i2c0_default: i2c0-default {
> st,pins {
> - sda = <&PIO9 3 ALT1 BIDIR>;
> - scl = <&PIO9 2 ALT1 BIDIR>;
> + sda = <&pio9 3 ALT1 BIDIR>;
> + scl = <&pio9 2 ALT1 BIDIR>;
> };
> };
> };
> @@ -283,8 +283,8 @@
> i2c1 {
> pinctrl_i2c1_default: i2c1-default {
> st,pins {
> - sda = <&PIO12 1 ALT1 BIDIR>;
> - scl = <&PIO12 0 ALT1 BIDIR>;
> + sda = <&pio12 1 ALT1 BIDIR>;
> + scl = <&pio12 0 ALT1 BIDIR>;
> };
> };
> };
> @@ -301,7 +301,7 @@
> interrupts-names = "irqmux";
> ranges = <0 0xfe820000 0x8000>;
>
> - PIO13: gpio at fe820000 {
> + pio13: gpio at fe820000 {
> gpio-controller;
> #gpio-cells = <1>;
> interrupt-controller;
> @@ -309,7 +309,7 @@
> reg = <0 0x100>;
> st,bank-name = "PIO13";
> };
> - PIO14: gpio at fe821000 {
> + pio14: gpio at fe821000 {
> gpio-controller;
> #gpio-cells = <1>;
> interrupt-controller;
> @@ -317,7 +317,7 @@
> reg = <0x1000 0x100>;
> st,bank-name = "PIO14";
> };
> - PIO15: gpio at fe822000 {
> + pio15: gpio at fe822000 {
> gpio-controller;
> #gpio-cells = <1>;
> interrupt-controller;
> @@ -325,7 +325,7 @@
> reg = <0x2000 0x100>;
> st,bank-name = "PIO15";
> };
> - PIO16: gpio at fe823000 {
> + pio16: gpio at fe823000 {
> gpio-controller;
> #gpio-cells = <1>;
> interrupt-controller;
> @@ -333,7 +333,7 @@
> reg = <0x3000 0x100>;
> st,bank-name = "PIO16";
> };
> - PIO17: gpio at fe824000 {
> + pio17: gpio at fe824000 {
> gpio-controller;
> #gpio-cells = <1>;
> interrupt-controller;
> @@ -341,7 +341,7 @@
> reg = <0x4000 0x100>;
> st,bank-name = "PIO17";
> };
> - PIO18: gpio at fe825000 {
> + pio18: gpio at fe825000 {
> gpio-controller;
> #gpio-cells = <1>;
> interrupt-controller;
> @@ -353,8 +353,8 @@
> serial2 {
> pinctrl_serial2: serial2-0 {
> st,pins {
> - tx = <&PIO17 4 ALT2 OUT>;
> - rx = <&PIO17 5 ALT2 IN>;
> + tx = <&pio17 4 ALT2 OUT>;
> + rx = <&pio17 5 ALT2 IN>;
> };
> };
> };
> @@ -362,68 +362,68 @@
> gmac0{
> pinctrl_mii0: mii0 {
> st,pins {
> - mdint = <&PIO13 6 ALT2 IN BYPASS 0>;
> - txen = <&PIO13 7 ALT2 OUT SE_NICLK_IO 0 CLK_A>;
> -
> - txd0 = <&PIO14 0 ALT2 OUT SE_NICLK_IO 0 CLK_A>;
> - txd1 = <&PIO14 1 ALT2 OUT SE_NICLK_IO 0 CLK_A>;
> - txd2 = <&PIO14 2 ALT2 OUT SE_NICLK_IO 0 CLK_B>;
> - txd3 = <&PIO14 3 ALT2 OUT SE_NICLK_IO 0 CLK_B>;
> -
> - txclk = <&PIO15 0 ALT2 IN NICLK 0 CLK_A>;
> - txer = <&PIO15 1 ALT2 OUT SE_NICLK_IO 0 CLK_A>;
> - crs = <&PIO15 2 ALT2 IN BYPASS 1000>;
> - col = <&PIO15 3 ALT2 IN BYPASS 1000>;
> - mdio = <&PIO15 4 ALT2 OUT BYPASS 3000>;
> - mdc = <&PIO15 5 ALT2 OUT NICLK 0 CLK_B>;
> -
> - rxd0 = <&PIO16 0 ALT2 IN SE_NICLK_IO 0 CLK_A>;
> - rxd1 = <&PIO16 1 ALT2 IN SE_NICLK_IO 0 CLK_A>;
> - rxd2 = <&PIO16 2 ALT2 IN SE_NICLK_IO 0 CLK_A>;
> - rxd3 = <&PIO16 3 ALT2 IN SE_NICLK_IO 0 CLK_A>;
> - rxdv = <&PIO15 6 ALT2 IN SE_NICLK_IO 0 CLK_A>;
> - rx_er = <&PIO15 7 ALT2 IN SE_NICLK_IO 0 CLK_A>;
> - rxclk = <&PIO17 0 ALT2 IN NICLK 0 CLK_A>;
> - phyclk = <&PIO13 5 ALT2 OUT NICLK 1000 CLK_A>;
> + mdint = <&pio13 6 ALT2 IN BYPASS 0>;
> + txen = <&pio13 7 ALT2 OUT SE_NICLK_IO 0 CLK_A>;
> +
> + txd0 = <&pio14 0 ALT2 OUT SE_NICLK_IO 0 CLK_A>;
> + txd1 = <&pio14 1 ALT2 OUT SE_NICLK_IO 0 CLK_A>;
> + txd2 = <&pio14 2 ALT2 OUT SE_NICLK_IO 0 CLK_B>;
> + txd3 = <&pio14 3 ALT2 OUT SE_NICLK_IO 0 CLK_B>;
> +
> + txclk = <&pio15 0 ALT2 IN NICLK 0 CLK_A>;
> + txer = <&pio15 1 ALT2 OUT SE_NICLK_IO 0 CLK_A>;
> + crs = <&pio15 2 ALT2 IN BYPASS 1000>;
> + col = <&pio15 3 ALT2 IN BYPASS 1000>;
> + mdio = <&pio15 4 ALT2 OUT BYPASS 3000>;
> + mdc = <&pio15 5 ALT2 OUT NICLK 0 CLK_B>;
> +
> + rxd0 = <&pio16 0 ALT2 IN SE_NICLK_IO 0 CLK_A>;
> + rxd1 = <&pio16 1 ALT2 IN SE_NICLK_IO 0 CLK_A>;
> + rxd2 = <&pio16 2 ALT2 IN SE_NICLK_IO 0 CLK_A>;
> + rxd3 = <&pio16 3 ALT2 IN SE_NICLK_IO 0 CLK_A>;
> + rxdv = <&pio15 6 ALT2 IN SE_NICLK_IO 0 CLK_A>;
> + rx_er = <&pio15 7 ALT2 IN SE_NICLK_IO 0 CLK_A>;
> + rxclk = <&pio17 0 ALT2 IN NICLK 0 CLK_A>;
> + phyclk = <&pio13 5 ALT2 OUT NICLK 1000 CLK_A>;
>
> };
> };
>
> pinctrl_gmii0: gmii0 {
> st,pins {
> - mdint = <&PIO13 6 ALT2 IN BYPASS 0>;
> - mdio = <&PIO15 4 ALT2 OUT BYPASS 3000>;
> - mdc = <&PIO15 5 ALT2 OUT NICLK 0 CLK_B>;
> - txen = <&PIO13 7 ALT2 OUT SE_NICLK_IO 3000 CLK_A>;
> -
> - txd0 = <&PIO14 0 ALT2 OUT SE_NICLK_IO 3000 CLK_A>;
> - txd1 = <&PIO14 1 ALT2 OUT SE_NICLK_IO 3000 CLK_A>;
> - txd2 = <&PIO14 2 ALT2 OUT SE_NICLK_IO 3000 CLK_B>;
> - txd3 = <&PIO14 3 ALT2 OUT SE_NICLK_IO 3000 CLK_B>;
> - txd4 = <&PIO14 4 ALT2 OUT SE_NICLK_IO 3000 CLK_B>;
> - txd5 = <&PIO14 5 ALT2 OUT SE_NICLK_IO 3000 CLK_B>;
> - txd6 = <&PIO14 6 ALT2 OUT SE_NICLK_IO 3000 CLK_B>;
> - txd7 = <&PIO14 7 ALT2 OUT SE_NICLK_IO 3000 CLK_B>;
> -
> - txclk = <&PIO15 0 ALT2 IN NICLK 0 CLK_A>;
> - txer = <&PIO15 1 ALT2 OUT SE_NICLK_IO 3000 CLK_A>;
> - crs = <&PIO15 2 ALT2 IN BYPASS 1000>;
> - col = <&PIO15 3 ALT2 IN BYPASS 1000>;
> - rxdv = <&PIO15 6 ALT2 IN SE_NICLK_IO 1500 CLK_A>;
> - rx_er = <&PIO15 7 ALT2 IN SE_NICLK_IO 1500 CLK_A>;
> -
> - rxd0 = <&PIO16 0 ALT2 IN SE_NICLK_IO 1500 CLK_A>;
> - rxd1 = <&PIO16 1 ALT2 IN SE_NICLK_IO 1500 CLK_A>;
> - rxd2 = <&PIO16 2 ALT2 IN SE_NICLK_IO 1500 CLK_A>;
> - rxd3 = <&PIO16 3 ALT2 IN SE_NICLK_IO 1500 CLK_A>;
> - rxd4 = <&PIO16 4 ALT2 IN SE_NICLK_IO 1500 CLK_A>;
> - rxd5 = <&PIO16 5 ALT2 IN SE_NICLK_IO 1500 CLK_A>;
> - rxd6 = <&PIO16 6 ALT2 IN SE_NICLK_IO 1500 CLK_A>;
> - rxd7 = <&PIO16 7 ALT2 IN SE_NICLK_IO 1500 CLK_A>;
> -
> - rxclk = <&PIO17 0 ALT2 IN NICLK 0 CLK_A>;
> - clk125 = <&PIO17 6 ALT1 IN NICLK 0 CLK_A>;
> - phyclk = <&PIO13 5 ALT4 OUT NICLK 0 CLK_B>;
> + mdint = <&pio13 6 ALT2 IN BYPASS 0>;
> + mdio = <&pio15 4 ALT2 OUT BYPASS 3000>;
> + mdc = <&pio15 5 ALT2 OUT NICLK 0 CLK_B>;
> + txen = <&pio13 7 ALT2 OUT SE_NICLK_IO 3000 CLK_A>;
> +
> + txd0 = <&pio14 0 ALT2 OUT SE_NICLK_IO 3000 CLK_A>;
> + txd1 = <&pio14 1 ALT2 OUT SE_NICLK_IO 3000 CLK_A>;
> + txd2 = <&pio14 2 ALT2 OUT SE_NICLK_IO 3000 CLK_B>;
> + txd3 = <&pio14 3 ALT2 OUT SE_NICLK_IO 3000 CLK_B>;
> + txd4 = <&pio14 4 ALT2 OUT SE_NICLK_IO 3000 CLK_B>;
> + txd5 = <&pio14 5 ALT2 OUT SE_NICLK_IO 3000 CLK_B>;
> + txd6 = <&pio14 6 ALT2 OUT SE_NICLK_IO 3000 CLK_B>;
> + txd7 = <&pio14 7 ALT2 OUT SE_NICLK_IO 3000 CLK_B>;
> +
> + txclk = <&pio15 0 ALT2 IN NICLK 0 CLK_A>;
> + txer = <&pio15 1 ALT2 OUT SE_NICLK_IO 3000 CLK_A>;
> + crs = <&pio15 2 ALT2 IN BYPASS 1000>;
> + col = <&pio15 3 ALT2 IN BYPASS 1000>;
> + rxdv = <&pio15 6 ALT2 IN SE_NICLK_IO 1500 CLK_A>;
> + rx_er = <&pio15 7 ALT2 IN SE_NICLK_IO 1500 CLK_A>;
> +
> + rxd0 = <&pio16 0 ALT2 IN SE_NICLK_IO 1500 CLK_A>;
> + rxd1 = <&pio16 1 ALT2 IN SE_NICLK_IO 1500 CLK_A>;
> + rxd2 = <&pio16 2 ALT2 IN SE_NICLK_IO 1500 CLK_A>;
> + rxd3 = <&pio16 3 ALT2 IN SE_NICLK_IO 1500 CLK_A>;
> + rxd4 = <&pio16 4 ALT2 IN SE_NICLK_IO 1500 CLK_A>;
> + rxd5 = <&pio16 5 ALT2 IN SE_NICLK_IO 1500 CLK_A>;
> + rxd6 = <&pio16 6 ALT2 IN SE_NICLK_IO 1500 CLK_A>;
> + rxd7 = <&pio16 7 ALT2 IN SE_NICLK_IO 1500 CLK_A>;
> +
> + rxclk = <&pio17 0 ALT2 IN NICLK 0 CLK_A>;
> + clk125 = <&pio17 6 ALT1 IN NICLK 0 CLK_A>;
> + phyclk = <&pio13 5 ALT4 OUT NICLK 0 CLK_B>;
>
>
> };
> @@ -442,7 +442,7 @@
> interrupts-names = "irqmux";
> ranges = <0 0xfd6b0000 0x3000>;
>
> - PIO100: gpio at fd6b0000 {
> + pio100: gpio at fd6b0000 {
> gpio-controller;
> #gpio-cells = <1>;
> interrupt-controller;
> @@ -450,7 +450,7 @@
> reg = <0 0x100>;
> st,bank-name = "PIO100";
> };
> - PIO101: gpio at fd6b1000 {
> + pio101: gpio at fd6b1000 {
> gpio-controller;
> #gpio-cells = <1>;
> interrupt-controller;
> @@ -458,7 +458,7 @@
> reg = <0x1000 0x100>;
> st,bank-name = "PIO101";
> };
> - PIO102: gpio at fd6b2000 {
> + pio102: gpio at fd6b2000 {
> gpio-controller;
> #gpio-cells = <1>;
> interrupt-controller;
> @@ -479,7 +479,7 @@
> interrupts-names = "irqmux";
> ranges = <0 0xfd330000 0x5000>;
>
> - PIO103: gpio at fd330000 {
> + pio103: gpio at fd330000 {
> gpio-controller;
> #gpio-cells = <1>;
> interrupt-controller;
> @@ -487,7 +487,7 @@
> reg = <0 0x100>;
> st,bank-name = "PIO103";
> };
> - PIO104: gpio at fd331000 {
> + pio104: gpio at fd331000 {
> gpio-controller;
> #gpio-cells = <1>;
> interrupt-controller;
> @@ -495,7 +495,7 @@
> reg = <0x1000 0x100>;
> st,bank-name = "PIO104";
> };
> - PIO105: gpio at fd332000 {
> + pio105: gpio at fd332000 {
> gpio-controller;
> #gpio-cells = <1>;
> interrupt-controller;
> @@ -503,7 +503,7 @@
> reg = <0x2000 0x100>;
> st,bank-name = "PIO105";
> };
> - PIO106: gpio at fd333000 {
> + pio106: gpio at fd333000 {
> gpio-controller;
> #gpio-cells = <1>;
> interrupt-controller;
> @@ -511,7 +511,7 @@
> reg = <0x3000 0x100>;
> st,bank-name = "PIO106";
> };
> - PIO107: gpio at fd334000 {
> + pio107: gpio at fd334000 {
> gpio-controller;
> #gpio-cells = <1>;
> interrupt-controller;
> diff --git a/arch/arm/boot/dts/stih416-b2020-revE.dts b/arch/arm/boot/dts/stih416-b2020-revE.dts
> index ba0fa2c..d72e5c7 100644
> --- a/arch/arm/boot/dts/stih416-b2020-revE.dts
> +++ b/arch/arm/boot/dts/stih416-b2020-revE.dts
> @@ -19,17 +19,17 @@
> red {
> #gpio-cells = <1>;
> label = "Front Panel LED";
> - gpios = <&PIO4 1>;
> + gpios = <&pio4 1>;
> linux,default-trigger = "heartbeat";
> };
> green {
> - gpios = <&PIO1 3>;
> + gpios = <&pio1 3>;
> default-state = "off";
> };
> };
>
> ethernet1: dwmac at fef08000 {
> - snps,reset-gpio = <&PIO0 7>;
> + snps,reset-gpio = <&pio0 7>;
> };
> };
> };
> diff --git a/arch/arm/boot/dts/stih416-pinctrl.dtsi b/arch/arm/boot/dts/stih416-pinctrl.dtsi
> index 6252188..3e06d7f 100644
> --- a/arch/arm/boot/dts/stih416-pinctrl.dtsi
> +++ b/arch/arm/boot/dts/stih416-pinctrl.dtsi
> @@ -12,36 +12,36 @@
> / {
>
> aliases {
> - gpio0 = &PIO0;
> - gpio1 = &PIO1;
> - gpio2 = &PIO2;
> - gpio3 = &PIO3;
> - gpio4 = &PIO4;
> - gpio5 = &PIO40;
> - gpio6 = &PIO5;
> - gpio7 = &PIO6;
> - gpio8 = &PIO7;
> - gpio9 = &PIO8;
> - gpio10 = &PIO9;
> - gpio11 = &PIO10;
> - gpio12 = &PIO11;
> - gpio13 = &PIO12;
> - gpio14 = &PIO30;
> - gpio15 = &PIO31;
> - gpio16 = &PIO13;
> - gpio17 = &PIO14;
> - gpio18 = &PIO15;
> - gpio19 = &PIO16;
> - gpio20 = &PIO17;
> - gpio21 = &PIO18;
> - gpio22 = &PIO100;
> - gpio23 = &PIO101;
> - gpio24 = &PIO102;
> - gpio25 = &PIO103;
> - gpio26 = &PIO104;
> - gpio27 = &PIO105;
> - gpio28 = &PIO106;
> - gpio29 = &PIO107;
> + gpio0 = &pio0;
> + gpio1 = &pio1;
> + gpio2 = &pio2;
> + gpio3 = &pio3;
> + gpio4 = &pio4;
> + gpio5 = &pio40;
> + gpio6 = &pio5;
> + gpio7 = &pio6;
> + gpio8 = &pio7;
> + gpio9 = &pio8;
> + gpio10 = &pio9;
> + gpio11 = &pio10;
> + gpio12 = &pio11;
> + gpio13 = &pio12;
> + gpio14 = &pio30;
> + gpio15 = &pio31;
> + gpio16 = &pio13;
> + gpio17 = &pio14;
> + gpio18 = &pio15;
> + gpio19 = &pio16;
> + gpio20 = &pio17;
> + gpio21 = &pio18;
> + gpio22 = &pio100;
> + gpio23 = &pio101;
> + gpio24 = &pio102;
> + gpio25 = &pio103;
> + gpio26 = &pio104;
> + gpio27 = &pio105;
> + gpio28 = &pio106;
> + gpio29 = &pio107;
> };
>
> soc {
> @@ -56,7 +56,7 @@
> interrupts-names = "irqmux";
> ranges = <0 0xfe610000 0x6000>;
>
> - PIO0: gpio at fe610000 {
> + pio0: gpio at fe610000 {
> gpio-controller;
> #gpio-cells = <1>;
> interrupt-controller;
> @@ -64,7 +64,7 @@
> reg = <0 0x100>;
> st,bank-name = "PIO0";
> };
> - PIO1: gpio at fe611000 {
> + pio1: gpio at fe611000 {
> gpio-controller;
> #gpio-cells = <1>;
> interrupt-controller;
> @@ -72,7 +72,7 @@
> reg = <0x1000 0x100>;
> st,bank-name = "PIO1";
> };
> - PIO2: gpio at fe612000 {
> + pio2: gpio at fe612000 {
> gpio-controller;
> #gpio-cells = <1>;
> interrupt-controller;
> @@ -80,7 +80,7 @@
> reg = <0x2000 0x100>;
> st,bank-name = "PIO2";
> };
> - PIO3: gpio at fe613000 {
> + pio3: gpio at fe613000 {
> gpio-controller;
> #gpio-cells = <1>;
> interrupt-controller;
> @@ -88,7 +88,7 @@
> reg = <0x3000 0x100>;
> st,bank-name = "PIO3";
> };
> - PIO4: gpio at fe614000 {
> + pio4: gpio at fe614000 {
> gpio-controller;
> #gpio-cells = <1>;
> interrupt-controller;
> @@ -96,7 +96,7 @@
> reg = <0x4000 0x100>;
> st,bank-name = "PIO4";
> };
> - PIO40: gpio at fe615000 {
> + pio40: gpio at fe615000 {
> gpio-controller;
> #gpio-cells = <1>;
> interrupt-controller;
> @@ -109,15 +109,15 @@
> rc{
> pinctrl_ir: ir0 {
> st,pins {
> - ir = <&PIO4 0 ALT2 IN>;
> + ir = <&pio4 0 ALT2 IN>;
> };
> };
> };
> sbc_serial1 {
> pinctrl_sbc_serial1: sbc_serial1 {
> st,pins {
> - tx = <&PIO2 6 ALT3 OUT>;
> - rx = <&PIO2 7 ALT3 IN>;
> + tx = <&pio2 6 ALT3 OUT>;
> + rx = <&pio2 7 ALT3 IN>;
> };
> };
> };
> @@ -125,15 +125,15 @@
> keyscan {
> pinctrl_keyscan: keyscan {
> st,pins {
> - keyin0 = <&PIO0 2 ALT2 IN>;
> - keyin1 = <&PIO0 3 ALT2 IN>;
> - keyin2 = <&PIO0 4 ALT2 IN>;
> - keyin3 = <&PIO2 6 ALT2 IN>;
> -
> - keyout0 = <&PIO1 6 ALT2 OUT>;
> - keyout1 = <&PIO1 7 ALT2 OUT>;
> - keyout2 = <&PIO0 6 ALT2 OUT>;
> - keyout3 = <&PIO2 7 ALT2 OUT>;
> + keyin0 = <&pio0 2 ALT2 IN>;
> + keyin1 = <&pio0 3 ALT2 IN>;
> + keyin2 = <&pio0 4 ALT2 IN>;
> + keyin3 = <&pio2 6 ALT2 IN>;
> +
> + keyout0 = <&pio1 6 ALT2 OUT>;
> + keyout1 = <&pio1 7 ALT2 OUT>;
> + keyout2 = <&pio0 6 ALT2 OUT>;
> + keyout3 = <&pio2 7 ALT2 OUT>;
> };
> };
> };
> @@ -141,8 +141,8 @@
> sbc_i2c0 {
> pinctrl_sbc_i2c0_default: sbc_i2c0-default {
> st,pins {
> - sda = <&PIO4 6 ALT1 BIDIR>;
> - scl = <&PIO4 5 ALT1 BIDIR>;
> + sda = <&pio4 6 ALT1 BIDIR>;
> + scl = <&pio4 5 ALT1 BIDIR>;
> };
> };
> };
> @@ -150,8 +150,8 @@
> sbc_i2c1 {
> pinctrl_sbc_i2c1_default: sbc_i2c1-default {
> st,pins {
> - sda = <&PIO3 2 ALT2 BIDIR>;
> - scl = <&PIO3 1 ALT2 BIDIR>;
> + sda = <&pio3 2 ALT2 BIDIR>;
> + scl = <&pio3 1 ALT2 BIDIR>;
> };
> };
> };
> @@ -159,51 +159,51 @@
> gmac1 {
> pinctrl_mii1: mii1 {
> st,pins {
> - txd0 = <&PIO0 0 ALT1 OUT SE_NICLK_IO 0 CLK_A>;
> - txd1 = <&PIO0 1 ALT1 OUT SE_NICLK_IO 0 CLK_A>;
> - txd2 = <&PIO0 2 ALT1 OUT SE_NICLK_IO 0 CLK_A>;
> - txd3 = <&PIO0 3 ALT1 OUT SE_NICLK_IO 0 CLK_A>;
> - txer = <&PIO0 4 ALT1 OUT SE_NICLK_IO 0 CLK_A>;
> - txen = <&PIO0 5 ALT1 OUT SE_NICLK_IO 0 CLK_A>;
> - txclk = <&PIO0 6 ALT1 IN NICLK 0 CLK_A>;
> - col = <&PIO0 7 ALT1 IN BYPASS 1000>;
> -
> - mdio = <&PIO1 0 ALT1 OUT BYPASS 1500>;
> - mdc = <&PIO1 1 ALT1 OUT NICLK 0 CLK_A>;
> - crs = <&PIO1 2 ALT1 IN BYPASS 1000>;
> - mdint = <&PIO1 3 ALT1 IN BYPASS 0>;
> - rxd0 = <&PIO1 4 ALT1 IN SE_NICLK_IO 0 CLK_A>;
> - rxd1 = <&PIO1 5 ALT1 IN SE_NICLK_IO 0 CLK_A>;
> - rxd2 = <&PIO1 6 ALT1 IN SE_NICLK_IO 0 CLK_A>;
> - rxd3 = <&PIO1 7 ALT1 IN SE_NICLK_IO 0 CLK_A>;
> -
> - rxdv = <&PIO2 0 ALT1 IN SE_NICLK_IO 0 CLK_A>;
> - rx_er = <&PIO2 1 ALT1 IN SE_NICLK_IO 0 CLK_A>;
> - rxclk = <&PIO2 2 ALT1 IN NICLK 0 CLK_A>;
> - phyclk = <&PIO2 3 ALT1 OUT NICLK 0 CLK_A>;
> + txd0 = <&pio0 0 ALT1 OUT SE_NICLK_IO 0 CLK_A>;
> + txd1 = <&pio0 1 ALT1 OUT SE_NICLK_IO 0 CLK_A>;
> + txd2 = <&pio0 2 ALT1 OUT SE_NICLK_IO 0 CLK_A>;
> + txd3 = <&pio0 3 ALT1 OUT SE_NICLK_IO 0 CLK_A>;
> + txer = <&pio0 4 ALT1 OUT SE_NICLK_IO 0 CLK_A>;
> + txen = <&pio0 5 ALT1 OUT SE_NICLK_IO 0 CLK_A>;
> + txclk = <&pio0 6 ALT1 IN NICLK 0 CLK_A>;
> + col = <&pio0 7 ALT1 IN BYPASS 1000>;
> +
> + mdio = <&pio1 0 ALT1 OUT BYPASS 1500>;
> + mdc = <&pio1 1 ALT1 OUT NICLK 0 CLK_A>;
> + crs = <&pio1 2 ALT1 IN BYPASS 1000>;
> + mdint = <&pio1 3 ALT1 IN BYPASS 0>;
> + rxd0 = <&pio1 4 ALT1 IN SE_NICLK_IO 0 CLK_A>;
> + rxd1 = <&pio1 5 ALT1 IN SE_NICLK_IO 0 CLK_A>;
> + rxd2 = <&pio1 6 ALT1 IN SE_NICLK_IO 0 CLK_A>;
> + rxd3 = <&pio1 7 ALT1 IN SE_NICLK_IO 0 CLK_A>;
> +
> + rxdv = <&pio2 0 ALT1 IN SE_NICLK_IO 0 CLK_A>;
> + rx_er = <&pio2 1 ALT1 IN SE_NICLK_IO 0 CLK_A>;
> + rxclk = <&pio2 2 ALT1 IN NICLK 0 CLK_A>;
> + phyclk = <&pio2 3 ALT1 OUT NICLK 0 CLK_A>;
> };
> };
> pinctrl_rgmii1: rgmii1-0 {
> st,pins {
> - txd0 = <&PIO0 0 ALT1 OUT DE_IO 500 CLK_A>;
> - txd1 = <&PIO0 1 ALT1 OUT DE_IO 500 CLK_A>;
> - txd2 = <&PIO0 2 ALT1 OUT DE_IO 500 CLK_A>;
> - txd3 = <&PIO0 3 ALT1 OUT DE_IO 500 CLK_A>;
> - txen = <&PIO0 5 ALT1 OUT DE_IO 0 CLK_A>;
> - txclk = <&PIO0 6 ALT1 IN NICLK 0 CLK_A>;
> -
> - mdio = <&PIO1 0 ALT1 OUT BYPASS 0>;
> - mdc = <&PIO1 1 ALT1 OUT NICLK 0 CLK_A>;
> - rxd0 = <&PIO1 4 ALT1 IN DE_IO 500 CLK_A>;
> - rxd1 = <&PIO1 5 ALT1 IN DE_IO 500 CLK_A>;
> - rxd2 = <&PIO1 6 ALT1 IN DE_IO 500 CLK_A>;
> - rxd3 = <&PIO1 7 ALT1 IN DE_IO 500 CLK_A>;
> -
> - rxdv = <&PIO2 0 ALT1 IN DE_IO 500 CLK_A>;
> - rxclk = <&PIO2 2 ALT1 IN NICLK 0 CLK_A>;
> - phyclk = <&PIO2 3 ALT4 OUT NICLK 0 CLK_B>;
> -
> - clk125= <&PIO3 7 ALT4 IN NICLK 0 CLK_A>;
> + txd0 = <&pio0 0 ALT1 OUT DE_IO 500 CLK_A>;
> + txd1 = <&pio0 1 ALT1 OUT DE_IO 500 CLK_A>;
> + txd2 = <&pio0 2 ALT1 OUT DE_IO 500 CLK_A>;
> + txd3 = <&pio0 3 ALT1 OUT DE_IO 500 CLK_A>;
> + txen = <&pio0 5 ALT1 OUT DE_IO 0 CLK_A>;
> + txclk = <&pio0 6 ALT1 IN NICLK 0 CLK_A>;
> +
> + mdio = <&pio1 0 ALT1 OUT BYPASS 0>;
> + mdc = <&pio1 1 ALT1 OUT NICLK 0 CLK_A>;
> + rxd0 = <&pio1 4 ALT1 IN DE_IO 500 CLK_A>;
> + rxd1 = <&pio1 5 ALT1 IN DE_IO 500 CLK_A>;
> + rxd2 = <&pio1 6 ALT1 IN DE_IO 500 CLK_A>;
> + rxd3 = <&pio1 7 ALT1 IN DE_IO 500 CLK_A>;
> +
> + rxdv = <&pio2 0 ALT1 IN DE_IO 500 CLK_A>;
> + rxclk = <&pio2 2 ALT1 IN NICLK 0 CLK_A>;
> + phyclk = <&pio2 3 ALT4 OUT NICLK 0 CLK_B>;
> +
> + clk125= <&pio3 7 ALT4 IN NICLK 0 CLK_A>;
> };
> };
> };
> @@ -220,7 +220,7 @@
> interrupts-names = "irqmux";
> ranges = <0 0xfee00000 0x10000>;
>
> - PIO5: gpio at fee00000 {
> + pio5: gpio at fee00000 {
> gpio-controller;
> #gpio-cells = <1>;
> interrupt-controller;
> @@ -228,7 +228,7 @@
> reg = <0 0x100>;
> st,bank-name = "PIO5";
> };
> - PIO6: gpio at fee01000 {
> + pio6: gpio at fee01000 {
> gpio-controller;
> #gpio-cells = <1>;
> interrupt-controller;
> @@ -236,7 +236,7 @@
> reg = <0x1000 0x100>;
> st,bank-name = "PIO6";
> };
> - PIO7: gpio at fee02000 {
> + pio7: gpio at fee02000 {
> gpio-controller;
> #gpio-cells = <1>;
> interrupt-controller;
> @@ -244,7 +244,7 @@
> reg = <0x2000 0x100>;
> st,bank-name = "PIO7";
> };
> - PIO8: gpio at fee03000 {
> + pio8: gpio at fee03000 {
> gpio-controller;
> #gpio-cells = <1>;
> interrupt-controller;
> @@ -252,7 +252,7 @@
> reg = <0x3000 0x100>;
> st,bank-name = "PIO8";
> };
> - PIO9: gpio at fee04000 {
> + pio9: gpio at fee04000 {
> gpio-controller;
> #gpio-cells = <1>;
> interrupt-controller;
> @@ -260,7 +260,7 @@
> reg = <0x4000 0x100>;
> st,bank-name = "PIO9";
> };
> - PIO10: gpio at fee05000 {
> + pio10: gpio at fee05000 {
> gpio-controller;
> #gpio-cells = <1>;
> interrupt-controller;
> @@ -268,7 +268,7 @@
> reg = <0x5000 0x100>;
> st,bank-name = "PIO10";
> };
> - PIO11: gpio at fee06000 {
> + pio11: gpio at fee06000 {
> gpio-controller;
> #gpio-cells = <1>;
> interrupt-controller;
> @@ -276,7 +276,7 @@
> reg = <0x6000 0x100>;
> st,bank-name = "PIO11";
> };
> - PIO12: gpio at fee07000 {
> + pio12: gpio at fee07000 {
> gpio-controller;
> #gpio-cells = <1>;
> interrupt-controller;
> @@ -284,7 +284,7 @@
> reg = <0x7000 0x100>;
> st,bank-name = "PIO12";
> };
> - PIO30: gpio at fee08000 {
> + pio30: gpio at fee08000 {
> gpio-controller;
> #gpio-cells = <1>;
> interrupt-controller;
> @@ -292,7 +292,7 @@
> reg = <0x8000 0x100>;
> st,bank-name = "PIO30";
> };
> - PIO31: gpio at fee09000 {
> + pio31: gpio at fee09000 {
> gpio-controller;
> #gpio-cells = <1>;
> interrupt-controller;
> @@ -304,7 +304,7 @@
> serial2-oe {
> pinctrl_serial2_oe: serial2-1 {
> st,pins {
> - output-enable = <&PIO11 3 ALT2 OUT>;
> + output-enable = <&pio11 3 ALT2 OUT>;
> };
> };
> };
> @@ -312,8 +312,8 @@
> i2c0 {
> pinctrl_i2c0_default: i2c0-default {
> st,pins {
> - sda = <&PIO9 3 ALT1 BIDIR>;
> - scl = <&PIO9 2 ALT1 BIDIR>;
> + sda = <&pio9 3 ALT1 BIDIR>;
> + scl = <&pio9 2 ALT1 BIDIR>;
> };
> };
> };
> @@ -321,8 +321,8 @@
> i2c1 {
> pinctrl_i2c1_default: i2c1-default {
> st,pins {
> - sda = <&PIO12 1 ALT1 BIDIR>;
> - scl = <&PIO12 0 ALT1 BIDIR>;
> + sda = <&pio12 1 ALT1 BIDIR>;
> + scl = <&pio12 0 ALT1 BIDIR>;
> };
> };
> };
> @@ -330,12 +330,12 @@
> fsm {
> pinctrl_fsm: fsm {
> st,pins {
> - spi-fsm-clk = <&PIO12 2 ALT1 OUT>;
> - spi-fsm-cs = <&PIO12 3 ALT1 OUT>;
> - spi-fsm-mosi = <&PIO12 4 ALT1 OUT>;
> - spi-fsm-miso = <&PIO12 5 ALT1 IN>;
> - spi-fsm-hol = <&PIO12 6 ALT1 OUT>;
> - spi-fsm-wp = <&PIO12 7 ALT1 OUT>;
> + spi-fsm-clk = <&pio12 2 ALT1 OUT>;
> + spi-fsm-cs = <&pio12 3 ALT1 OUT>;
> + spi-fsm-mosi = <&pio12 4 ALT1 OUT>;
> + spi-fsm-miso = <&pio12 5 ALT1 IN>;
> + spi-fsm-hol = <&pio12 6 ALT1 OUT>;
> + spi-fsm-wp = <&pio12 7 ALT1 OUT>;
> };
> };
> };
> @@ -352,7 +352,7 @@
> interrupts-names = "irqmux";
> ranges = <0 0xfe820000 0x6000>;
>
> - PIO13: gpio at fe820000 {
> + pio13: gpio at fe820000 {
> gpio-controller;
> #gpio-cells = <1>;
> interrupt-controller;
> @@ -360,7 +360,7 @@
> reg = <0 0x100>;
> st,bank-name = "PIO13";
> };
> - PIO14: gpio at fe821000 {
> + pio14: gpio at fe821000 {
> gpio-controller;
> #gpio-cells = <1>;
> interrupt-controller;
> @@ -368,7 +368,7 @@
> reg = <0x1000 0x100>;
> st,bank-name = "PIO14";
> };
> - PIO15: gpio at fe822000 {
> + pio15: gpio at fe822000 {
> gpio-controller;
> #gpio-cells = <1>;
> interrupt-controller;
> @@ -376,7 +376,7 @@
> reg = <0x2000 0x100>;
> st,bank-name = "PIO15";
> };
> - PIO16: gpio at fe823000 {
> + pio16: gpio at fe823000 {
> gpio-controller;
> #gpio-cells = <1>;
> interrupt-controller;
> @@ -384,7 +384,7 @@
> reg = <0x3000 0x100>;
> st,bank-name = "PIO16";
> };
> - PIO17: gpio at fe824000 {
> + pio17: gpio at fe824000 {
> gpio-controller;
> #gpio-cells = <1>;
> interrupt-controller;
> @@ -392,7 +392,7 @@
> reg = <0x4000 0x100>;
> st,bank-name = "PIO17";
> };
> - PIO18: gpio at fe825000 {
> + pio18: gpio at fe825000 {
> gpio-controller;
> #gpio-cells = <1>;
> interrupt-controller;
> @@ -405,8 +405,8 @@
> serial2 {
> pinctrl_serial2: serial2-0 {
> st,pins {
> - tx = <&PIO17 4 ALT2 OUT>;
> - rx = <&PIO17 5 ALT2 IN>;
> + tx = <&pio17 4 ALT2 OUT>;
> + rx = <&pio17 5 ALT2 IN>;
> };
> };
> };
> @@ -414,28 +414,28 @@
> gmac0 {
> pinctrl_mii0: mii0 {
> st,pins {
> - mdint = <&PIO13 6 ALT2 IN BYPASS 0>;
> - txen = <&PIO13 7 ALT2 OUT SE_NICLK_IO 0 CLK_A>;
> - txd0 = <&PIO14 0 ALT2 OUT SE_NICLK_IO 0 CLK_A>;
> - txd1 = <&PIO14 1 ALT2 OUT SE_NICLK_IO 0 CLK_A>;
> - txd2 = <&PIO14 2 ALT2 OUT SE_NICLK_IO 0 CLK_B>;
> - txd3 = <&PIO14 3 ALT2 OUT SE_NICLK_IO 0 CLK_B>;
> -
> - txclk = <&PIO15 0 ALT2 IN NICLK 0 CLK_A>;
> - txer = <&PIO15 1 ALT2 OUT SE_NICLK_IO 0 CLK_A>;
> - crs = <&PIO15 2 ALT2 IN BYPASS 1000>;
> - col = <&PIO15 3 ALT2 IN BYPASS 1000>;
> - mdio= <&PIO15 4 ALT2 OUT BYPASS 1500>;
> - mdc = <&PIO15 5 ALT2 OUT NICLK 0 CLK_B>;
> -
> - rxd0 = <&PIO16 0 ALT2 IN SE_NICLK_IO 0 CLK_A>;
> - rxd1 = <&PIO16 1 ALT2 IN SE_NICLK_IO 0 CLK_A>;
> - rxd2 = <&PIO16 2 ALT2 IN SE_NICLK_IO 0 CLK_A>;
> - rxd3 = <&PIO16 3 ALT2 IN SE_NICLK_IO 0 CLK_A>;
> - rxdv = <&PIO15 6 ALT2 IN SE_NICLK_IO 0 CLK_A>;
> - rx_er = <&PIO15 7 ALT2 IN SE_NICLK_IO 0 CLK_A>;
> - rxclk = <&PIO17 0 ALT2 IN NICLK 0 CLK_A>;
> - phyclk = <&PIO13 5 ALT2 OUT NICLK 0 CLK_B>;
> + mdint = <&pio13 6 ALT2 IN BYPASS 0>;
> + txen = <&pio13 7 ALT2 OUT SE_NICLK_IO 0 CLK_A>;
> + txd0 = <&pio14 0 ALT2 OUT SE_NICLK_IO 0 CLK_A>;
> + txd1 = <&pio14 1 ALT2 OUT SE_NICLK_IO 0 CLK_A>;
> + txd2 = <&pio14 2 ALT2 OUT SE_NICLK_IO 0 CLK_B>;
> + txd3 = <&pio14 3 ALT2 OUT SE_NICLK_IO 0 CLK_B>;
> +
> + txclk = <&pio15 0 ALT2 IN NICLK 0 CLK_A>;
> + txer = <&pio15 1 ALT2 OUT SE_NICLK_IO 0 CLK_A>;
> + crs = <&pio15 2 ALT2 IN BYPASS 1000>;
> + col = <&pio15 3 ALT2 IN BYPASS 1000>;
> + mdio= <&pio15 4 ALT2 OUT BYPASS 1500>;
> + mdc = <&pio15 5 ALT2 OUT NICLK 0 CLK_B>;
> +
> + rxd0 = <&pio16 0 ALT2 IN SE_NICLK_IO 0 CLK_A>;
> + rxd1 = <&pio16 1 ALT2 IN SE_NICLK_IO 0 CLK_A>;
> + rxd2 = <&pio16 2 ALT2 IN SE_NICLK_IO 0 CLK_A>;
> + rxd3 = <&pio16 3 ALT2 IN SE_NICLK_IO 0 CLK_A>;
> + rxdv = <&pio15 6 ALT2 IN SE_NICLK_IO 0 CLK_A>;
> + rx_er = <&pio15 7 ALT2 IN SE_NICLK_IO 0 CLK_A>;
> + rxclk = <&pio17 0 ALT2 IN NICLK 0 CLK_A>;
> + phyclk = <&pio13 5 ALT2 OUT NICLK 0 CLK_B>;
> };
> };
>
> @@ -445,25 +445,25 @@
> };
> pinctrl_rgmii0: rgmii0 {
> st,pins {
> - phyclk = <&PIO13 5 ALT4 OUT NICLK 0 CLK_B>;
> - txen = <&PIO13 7 ALT2 OUT DE_IO 0 CLK_A>;
> - txd0 = <&PIO14 0 ALT2 OUT DE_IO 500 CLK_A>;
> - txd1 = <&PIO14 1 ALT2 OUT DE_IO 500 CLK_A>;
> - txd2 = <&PIO14 2 ALT2 OUT DE_IO 500 CLK_B>;
> - txd3 = <&PIO14 3 ALT2 OUT DE_IO 500 CLK_B>;
> - txclk = <&PIO15 0 ALT2 IN NICLK 0 CLK_A>;
> -
> - mdio = <&PIO15 4 ALT2 OUT BYPASS 0>;
> - mdc = <&PIO15 5 ALT2 OUT NICLK 0 CLK_B>;
> -
> - rxdv = <&PIO15 6 ALT2 IN DE_IO 500 CLK_A>;
> - rxd0 =<&PIO16 0 ALT2 IN DE_IO 500 CLK_A>;
> - rxd1 =<&PIO16 1 ALT2 IN DE_IO 500 CLK_A>;
> - rxd2 =<&PIO16 2 ALT2 IN DE_IO 500 CLK_A>;
> - rxd3 =<&PIO16 3 ALT2 IN DE_IO 500 CLK_A>;
> - rxclk =<&PIO17 0 ALT2 IN NICLK 0 CLK_A>;
> -
> - clk125=<&PIO17 6 ALT1 IN NICLK 0 CLK_A>;
> + phyclk = <&pio13 5 ALT4 OUT NICLK 0 CLK_B>;
> + txen = <&pio13 7 ALT2 OUT DE_IO 0 CLK_A>;
> + txd0 = <&pio14 0 ALT2 OUT DE_IO 500 CLK_A>;
> + txd1 = <&pio14 1 ALT2 OUT DE_IO 500 CLK_A>;
> + txd2 = <&pio14 2 ALT2 OUT DE_IO 500 CLK_B>;
> + txd3 = <&pio14 3 ALT2 OUT DE_IO 500 CLK_B>;
> + txclk = <&pio15 0 ALT2 IN NICLK 0 CLK_A>;
> +
> + mdio = <&pio15 4 ALT2 OUT BYPASS 0>;
> + mdc = <&pio15 5 ALT2 OUT NICLK 0 CLK_B>;
> +
> + rxdv = <&pio15 6 ALT2 IN DE_IO 500 CLK_A>;
> + rxd0 =<&pio16 0 ALT2 IN DE_IO 500 CLK_A>;
> + rxd1 =<&pio16 1 ALT2 IN DE_IO 500 CLK_A>;
> + rxd2 =<&pio16 2 ALT2 IN DE_IO 500 CLK_A>;
> + rxd3 =<&pio16 3 ALT2 IN DE_IO 500 CLK_A>;
> + rxclk =<&pio17 0 ALT2 IN NICLK 0 CLK_A>;
> +
> + clk125=<&pio17 6 ALT1 IN NICLK 0 CLK_A>;
> };
> };
> };
> @@ -480,7 +480,7 @@
> interrupts-names = "irqmux";
> ranges = <0 0xfd6b0000 0x3000>;
>
> - PIO100: gpio at fd6b0000 {
> + pio100: gpio at fd6b0000 {
> gpio-controller;
> #gpio-cells = <1>;
> interrupt-controller;
> @@ -488,7 +488,7 @@
> reg = <0 0x100>;
> st,bank-name = "PIO100";
> };
> - PIO101: gpio at fd6b1000 {
> + pio101: gpio at fd6b1000 {
> gpio-controller;
> #gpio-cells = <1>;
> interrupt-controller;
> @@ -496,7 +496,7 @@
> reg = <0x1000 0x100>;
> st,bank-name = "PIO101";
> };
> - PIO102: gpio at fd6b2000 {
> + pio102: gpio at fd6b2000 {
> gpio-controller;
> #gpio-cells = <1>;
> interrupt-controller;
> @@ -517,7 +517,7 @@
> interrupts-names = "irqmux";
> ranges = <0 0xfd330000 0x5000>;
>
> - PIO103: gpio at fd330000 {
> + pio103: gpio at fd330000 {
> gpio-controller;
> #gpio-cells = <1>;
> interrupt-controller;
> @@ -525,7 +525,7 @@
> reg = <0 0x100>;
> st,bank-name = "PIO103";
> };
> - PIO104: gpio at fd331000 {
> + pio104: gpio at fd331000 {
> gpio-controller;
> #gpio-cells = <1>;
> interrupt-controller;
> @@ -533,7 +533,7 @@
> reg = <0x1000 0x100>;
> st,bank-name = "PIO104";
> };
> - PIO105: gpio at fd332000 {
> + pio105: gpio at fd332000 {
> gpio-controller;
> #gpio-cells = <1>;
> interrupt-controller;
> @@ -541,7 +541,7 @@
> reg = <0x2000 0x100>;
> st,bank-name = "PIO105";
> };
> - PIO106: gpio at fd333000 {
> + pio106: gpio at fd333000 {
> gpio-controller;
> #gpio-cells = <1>;
> interrupt-controller;
> @@ -550,7 +550,7 @@
> st,bank-name = "PIO106";
> };
>
> - PIO107: gpio at fd334000 {
> + pio107: gpio at fd334000 {
> gpio-controller;
> #gpio-cells = <1>;
> interrupt-controller;
> diff --git a/arch/arm/boot/dts/stih41x-b2000.dtsi b/arch/arm/boot/dts/stih41x-b2000.dtsi
> index b3dd6ca..5f91f45 100644
> --- a/arch/arm/boot/dts/stih41x-b2000.dtsi
> +++ b/arch/arm/boot/dts/stih41x-b2000.dtsi
> @@ -35,7 +35,7 @@
> fp_led {
> #gpio-cells = <1>;
> label = "Front Panel LED";
> - gpios = <&PIO105 7>;
> + gpios = <&pio105 7>;
> linux,default-trigger = "heartbeat";
> };
> };
> @@ -55,7 +55,7 @@
> phy-mode = "mii";
> pinctrl-0 = <&pinctrl_mii0>;
>
> - snps,reset-gpio = <&PIO106 2>;
> + snps,reset-gpio = <&pio106 2>;
> snps,reset-active-low;
> snps,reset-delays-us = <0 10000 10000>;
> };
> @@ -65,7 +65,7 @@
> phy-mode = "mii";
> st,tx-retime-src = "txclk";
>
> - snps,reset-gpio = <&PIO4 7>;
> + snps,reset-gpio = <&pio4 7>;
> snps,reset-active-low;
> snps,reset-delays-us = <0 10000 10000>;
> };
> diff --git a/arch/arm/boot/dts/stih41x-b2020.dtsi b/arch/arm/boot/dts/stih41x-b2020.dtsi
> index d8a8429..c0f50e9 100644
> --- a/arch/arm/boot/dts/stih41x-b2020.dtsi
> +++ b/arch/arm/boot/dts/stih41x-b2020.dtsi
> @@ -32,11 +32,11 @@
> red {
> #gpio-cells = <1>;
> label = "Front Panel LED";
> - gpios = <&PIO4 1>;
> + gpios = <&pio4 1>;
> linux,default-trigger = "heartbeat";
> };
> green {
> - gpios = <&PIO4 7>;
> + gpios = <&pio4 7>;
> default-state = "off";
> };
> };
> @@ -68,7 +68,7 @@
> phy-mode = "rgmii-id";
> max-speed = <1000>;
> st,tx-retime-src = "clk_125";
> - snps,reset-gpio = <&PIO3 0>;
> + snps,reset-gpio = <&pio3 0>;
> snps,reset-active-low;
> snps,reset-delays-us = <0 10000 10000>;
>
--
Lee Jones
Linaro STMicroelectronics Landing Team Lead
Linaro.org │ Open source software for ARM SoCs
Follow Linaro: Facebook | Twitter | Blog
More information about the linux-arm-kernel
mailing list