[PATCH v14 04/10] imx-drm: use defines for clock polarity settings

Sascha Hauer s.hauer at pengutronix.de
Tue Jun 24 21:48:45 PDT 2014


On Mon, Jun 16, 2014 at 12:11:18PM +0200, Denis Carikli wrote:
> Signed-off-by: Denis Carikli <denis at eukrea.com>
> ---
> ChangeLog v13->v14:
> - Rebased
> ChangeLog 12->v13:
> - No changes
> ChangeLog 11->v12:
> - Improved the define names to match the hardware:
>   ENABLE_POL is not a clock signal but instead an enable signal.
> 
> ChangeLog v9->v10:
> - New patch which was splitted out from:
>   "staging: imx-drm: Use de-active and pixelclk-active display-timings.".
> - Fixes many issues in "staging: imx-drm: Use de-active and pixelclk-active
>   display-timings.":
>   - More clear meaning of the polarity settings.
>   - The SET_CLK_POL and SET_DE_POL masks are not
>     needed anymore.
> ---
>  drivers/gpu/ipu-v3/ipu-di.c          |    4 ++--
>  drivers/staging/imx-drm/ipuv3-crtc.c |    4 ++--
>  include/video/imx-ipu-v3.h           |    8 +++++++-
>  3 files changed, 11 insertions(+), 5 deletions(-)
> 
> diff --git a/drivers/gpu/ipu-v3/ipu-di.c b/drivers/gpu/ipu-v3/ipu-di.c
> index c490ba4..d00f357 100644
> --- a/drivers/gpu/ipu-v3/ipu-di.c
> +++ b/drivers/gpu/ipu-v3/ipu-di.c
> @@ -595,7 +595,7 @@ int ipu_di_init_sync_panel(struct ipu_di *di, struct ipu_di_signal_cfg *sig)
>  		}
>  	}
>  
> -	if (sig->clk_pol)
> +	if (sig->clk_pol == CLK_POL_POSEDGE)
>  		di_gen |= DI_GEN_POLARITY_DISP_CLK;
>  
>  	ipu_di_write(di, di_gen, DI_GENERAL);
> @@ -606,7 +606,7 @@ int ipu_di_init_sync_panel(struct ipu_di *di, struct ipu_di_signal_cfg *sig)
>  	reg = ipu_di_read(di, DI_POL);
>  	reg &= ~(DI_POL_DRDY_DATA_POLARITY | DI_POL_DRDY_POLARITY_15);
>  
> -	if (sig->enable_pol)
> +	if (sig->enable_pol == ENABLE_POL_HIGH)
>  		reg |= DI_POL_DRDY_POLARITY_15;
>  	if (sig->data_pol)
>  		reg |= DI_POL_DRDY_DATA_POLARITY;
> diff --git a/drivers/staging/imx-drm/ipuv3-crtc.c b/drivers/staging/imx-drm/ipuv3-crtc.c
> index 720868b..7fec438 100644
> --- a/drivers/staging/imx-drm/ipuv3-crtc.c
> +++ b/drivers/staging/imx-drm/ipuv3-crtc.c
> @@ -165,8 +165,8 @@ static int ipu_crtc_mode_set(struct drm_crtc *crtc,
>  	if (mode->flags & DRM_MODE_FLAG_PVSYNC)
>  		sig_cfg.Vsync_pol = 1;
>  
> -	sig_cfg.enable_pol = 1;
> -	sig_cfg.clk_pol = 0;
> +	sig_cfg.enable_pol = ENABLE_POL_HIGH;
> +	sig_cfg.clk_pol = CLK_POL_NEGEDGE;
>  	sig_cfg.width = mode->hdisplay;
>  	sig_cfg.height = mode->vdisplay;
>  	sig_cfg.pixel_fmt = out_pixel_fmt;
> diff --git a/include/video/imx-ipu-v3.h b/include/video/imx-ipu-v3.h
> index 3e43e22..8888305 100644
> --- a/include/video/imx-ipu-v3.h
> +++ b/include/video/imx-ipu-v3.h
> @@ -27,6 +27,12 @@ enum ipuv3_type {
>  
>  #define IPU_PIX_FMT_GBR24	v4l2_fourcc('G', 'B', 'R', '3')
>  
> +#define CLK_POL_NEGEDGE		0
> +#define CLK_POL_POSEDGE		1
> +
> +#define ENABLE_POL_LOW		0
> +#define ENABLE_POL_HIGH		1

Adding defines without a proper namespace (IPU_) outside a driver
private header file is not nice. Anyway, instead of adding the
defines ...

> +
>  /*
>   * Bitfield of Display Interface signal polarities.
>   */
> @@ -37,7 +43,7 @@ struct ipu_di_signal_cfg {
>  	unsigned clksel_en:1;
>  	unsigned clkidle_en:1;
>  	unsigned data_pol:1;	/* true = inverted */
> -	unsigned clk_pol:1;	/* true = rising edge */
> +	unsigned clk_pol:1;
>  	unsigned enable_pol:1;
>  	unsigned Hsync_pol:1;	/* true = active high */
>  	unsigned Vsync_pol:1;

...can we rename the flags to more meaningful names instead?

	unsigned clk_pol_rising_edge:1;
	unsigned enable_pol_high:1;
	unsigned hsync_active_high:1;
	unsigned vsync_active_high:1;

Sascha

-- 
Pengutronix e.K.                           |                             |
Industrial Linux Solutions                 | http://www.pengutronix.de/  |
Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0    |
Amtsgericht Hildesheim, HRA 2686           | Fax:   +49-5121-206917-5555 |



More information about the linux-arm-kernel mailing list